3310 Series Datasheet by Bourns Inc.

Datasheet Feedback/Errors

3310 – 9 mm Square Sealed Panel Control

Features

n Conductive plastic

n PC board and bushing mount

n Plastic or metal bushing and plastic shaft

n Withstands typical industrial washing

processes

n Compact package saves board and panel

space

Electrical Characteristics1

Standard Resistance Range - Linear �� 1 K ohms to 1 megohm

Total Resistance Tolerance - Linear Tapers �� ±20 %

Independent Linearity �� ±5 %

End Resistance ��2 % or 2 ohms maximum (whichever is greater)

Effective Electrical Angle ��270 ° ±15 °

Contact Resistance Variation �� 1 % or 1 ohm (whichever is greater)

Dielectric Withstanding Voltage (MIL-STD-202 – Method 301)

Sea Level ��900 VAC minimum

70,000 Feet ��350 VAC minimum

Insulation Resistance ��1,000 megohms minimum

Power Rating @ 70 °C (Derate to 0 at 125 °C - Voltage Limited By Power Dissipation or 200 VAC, Whichever is Less) �� 0�25 watts

Theoretical Resolution �� Essentially infinite

Environmental Characteristics

Operating Temperature Range �� -40 °C to +125 °C (-40 °F to +257 °F)

Storage Temperature Range ��-55 °C to +125 °C (-67 °F to +257 °F)

Temperature Coefficient Over Storage Temperature Range �� ±1,000 ppm/°C

Vibration ��30 G

Total Resistance Shift ��±1 % maximum

Voltage Ratio Shift ��±1 % maximum

Shock��100 G

Total Resistance Shift ��±1 % maximum

Voltage Ratio Shift ��±1 % maximum

Load Life �� 1,000 hours

Total Resistance Shift ��±10 % TRS maximum

Rotational Life (No Load)�� 50,000 cycles

Total Resistance Shift ��±5 % TRS maximum

Contact Resistance Variation ��3 % or 3 ohms (whichever is greater)

Moisture Resistance �� MIL-STD-202, Method 103, Condition B

Total Resistance Shift ��±10 % TRS maximum

IP Rating �� IP67

Moisture Sensitivity Level �� 1

ESD Classification (HBM)��N/A

Mechanical Characteristics

Stop Strength��5�65 N-cm (8 oz�-in�)

Mechanical Angle �� 300 ° nominal

Torque

Starting �� 3�53 N-cm (5�0 oz�-in�) maximum

Running �� 3�53 N-cm (5�0 oz�-in�) maximum

Mounting (Torque on Bushing) ��45 N-cm (4�0 lb�-in�) max [plastic bushing]; 79 N-cm (7�0 lb�-in�) max [metal bushing]

Weight (Single Section) �� 4�5 grams

(Each Additional Section) �� 2�5 grams

Terminals ��Solderable pins

Soldering Condition

Manual Soldering �� 96�5Sn/3�0Ag/0�5Cu solid wire or no-clean rosin cored wire; 370 °C (700 °F) max� for 3 seconds

Wave Soldering ��96�5Sn/3�0Ag/0�5Cu solder with no-clean flux; 260 °C (500 °F) max� for 5 seconds

Wash Processes ��For recommended wash processes, please refer to http://www�bourns�com/pdfs/sldclen�pdf

Marking �� Manufacturer’s trademark, model number, product code, terminal style, resistance code and date code

Ganging �� 2 cups maximum

Hardware ��One lockwasher (H-37-5) and one mounting nut (H-38-1) is shipped with each potentiometer, except bushingless versions

Flammability ��Conforms to UL94V-0

Epoxy��Conforms to UL 94V-1

IP Rating �� IP67

Switch Characteristics

Switch Life ��10K cycles

Contact Resistance ��2 ohms max�

Dielectric Strength ��350 VDC

Detent Torque ��0�5 oz-in min�

Power Rating (Resistive Load) �� 100 mA @ 16 VDC

1Electrical specifications tested at 60 RPM, at room ambient: +25 °C nominal�

WARNING

Cancer and Reproductive Harm

www.P65Warnings.ca.gov

*RoHS Directive 2015/863, Mar 31, 2015 and Annex.

Specifications are subject to change without notice. Users should verify actual device performance in their specific

applications. The products described herein and this document are subject to specific legal disclaimers as set forth on the

last page of this document, and at www.bourns.com/docs/legal/disclaimer.pdf.

BOURNS 200900 500900 ‘ ‘uoo‘ouo YVWWM 31 F V 001 10 L

3310 – 9 mm Square Sealed Panel Control

Additional Features

n Audio taper versions available as special order

n RoHS compliant*

Standard Resistance Table

Resistance Resistance

(Ohms) Code

1,000 102

2,000 202

5,000 502

10,000 103

20,000 203

50,000 503

100,000 104

200,000 204

500,000 504

1,000,000 105

Popular values listed in boldface� Consult factory

for special resistances�

How To Order

3310 Y - 0 0 1 - 103 L

Model Number Designator

3310 = 9 mm Panel Control

Terminal Style Designator

Single Cup:

C = In-line Straight Terminals Side Exit 2�54 mm centers

R = In-line Terminals Rear Exit 2�54 mm centers

P = 5�08 mm x 2�54 mm Triangular Pattern Rear Exit

Y = 5�08 mm x 5�08 mm Triangular Pattern Rear Exit

Dual Cup (Pot/Pot or Pot/Switch):

H = Dual In-line Straight Terminals Rear Exit 2�54 mm centers

Shaft End Designator

0 = Shaft End Slotted

1 = Shaft End Flatted

Shaft Length Designator

0 = 12�7 mm FMS Long Plastic Shaft (Available w/bushing only)

1 = 19�05 mm FMS Long Plastic Shaft (Available w/bushing only)

2 = 5�59 mm FMS Long Plastic Shaft (Bushingless version only)

Bushing Designator

Pot (or Pot/Pot):

1 = 6�35 mm x 6�35 mm Plastic

2 = 6�35 mm x 6�35 mm Ni Plated Brass

5 = Bushingless (Board Level Control)

Pot/Switch Bushing Designator (use with “H” terminal style only�)

3 = 6�35 mm x 6�35 mm Plastic

4 = 6�35 mm x 6�35 mm Ni Plated Brass

6 = Bushingless (Board Level)

Resistance Code

(1st 2 digits are significant, 3rd digit is number of 0s to follow)

RoHS Identifier

L = Compliant

Specifications are subject to change without notice.

Users should verify actual device performance in their specific applications.

The products described herein and this document are subject to specific legal disclaimers as set forth on the last page of this document, and at www.bourns.com/docs/legal/disclaimer.pdf.

Date Code Description

YY = LAST TWO DIGITS OF YEAR

MANUFACTURED

WW = WEEK NUMBER

M = COUNTRY OF MANUFACTURE

(MEXICO)

YWWM

BOURNS 5‘ 2 n5 \u2n2 n02] ’2‘ (72:5 935; 2522 25 2542 25 [m02 um (um: mu; 32 m5] *1 2232 25 H9" , run] 535 M ’

3310 – 9 mm Square Sealed Panel Control

Specifications are subject to change without notice.

Users should verify actual device performance in their specific applications.

The products described herein and this document are subject to specific legal disclaimers as set forth on the last page of this document, and at www.bourns.com/docs/legal/disclaimer.pdf.

Product Dimensions

COMMON DIMENSIONS

3310-001

Plastic Bushing

Slotted Shaft

MOUNTING HOLE PATTERN

COMMON DIMENSIONS

3310C-101

Plastic Flatted Shaft

3310C-001 3310Y-001

3310P-001

3310R-001

9.53 ± .25

(.375 ± .010)

9.53 ± .25

(.375 ± .010)

9.53 ± .25

(.375 ± .010)

9.53 ± .25

(.375 ± .010)

9.53 ± .25

(.375 ± .010)

.391 ± .38

(.154 ± .015)

9.53 ± .25

(.375 ± .010)

5.97 ± .89

(.235 ± .035)

2.54 ± .25

(.100 ± .010)

2.54 ± .25

(.100 ± .010)

2.54 ± .25

(.100 ± .010)

2.54 ± .38

(.100 ± .015)

MOUNTING

SURFACE

4.83

(.190)

2.39

(.094)

5.08 ± .25

(.200 ± .010)

5.97 ± .89

(.235 ± .035)

2.54 ± .25

(.100 ± .010)

2.54 ± .25

(.100 ± .010)

2.54 ± .25

(.100 ± .010)

2.54 ± .25

(.100 ± .010)

2.54 ± .25

(.100 ± .010)

2.54 ± .25

(.100 ± .010)

5.97 ± .89

(.235 ± .035)

5.97 ± .89

(.235 ± .035)

2.54 ± .25

(.100 ± .010)

.51 ± .05

(.020 ± .002)

SOLDER PLATED

COPPER PINS

DIA.

3.18 ± .05

(.125 ± .002)

DIA.

.64 ± .10

(.025 ± .004) WIDE

.76 ± .25

(.030 ± .010) DEEPX

.51

(.020) 4 PLACES

DIA. MOUNTING

SURFACE

1.70 ± 0.03

(.067 ± .001)

DIA.

6.53 ± 0.03

(.257 ± .001)

DIA.

4.78

(.188)

4.78

(.188)

7.62

(.300)

.38

(.015)

MIN.

STANDOFF

.76 ± .05 X .76

(.030 ± .002 X .030)

ANTI-ROTATION

BOSS

HIGHR

6.35 ± .08

(.250 ± .003)

MOUNTING

DIA.

4.83 ± .25

(.190 ± .010)

4.83 ± .38

(.190 ± .015) 6.35 ± .08

(.250 ± .003)

MOUNTING DIA.

12.70 ± .64

(.500 ± .025)

FROM MOUNTING

SURFACE

5.18 ± .38

(.204 ± .015)

12.70 ± .64

(.500 ± .025)

ADJUSTMENT SLOT

4.75

(.187)

MIN. FULL

THREAD

6.35

(.250)

.38

(.015)

MIN.

STANDOFF

1/4-32 UNEF-2A

THREADED PLASTIC

BUSHING

MOUNTING

SURFACE

DIMENSIONS: MM

(INCHES)

BOURNS COMMON DIMENSIONS 331 0-00; Mekal Bushing ass (Tam 535 m ‘ mm 64 (259,» 925; mm: H25: 7 5x a? [030 a DD? X DEE) 7 52 Tum i \DVS) Tl a 1 mm 33109-00; 331 op-oz_5« Bush glass (sun mm; 5 35 1 2n \25n1 ans, 5p m m2 ianm’ 5mm mmiuzsy' 559 > 32 (229 m5; (2551on ‘ (3951 m2] {375% may (4433 mm) "Him n2, (mum;

3310 – 9 mm Square Sealed Panel Control

Product Dimensions

6.35 ± .08

(.250 ± .003)

MOUNTING DIA.

7.62 ± .20

(.300 ± .008) DIA.

6.35 ± .20

(.250 ± .008) DIA.

.51 ± .10

(.020 ± .004)

5.18 ± .64

(.204 ± .025)

5.59 ± .38

(.220 ± .015)

4.83 ± .25

(.190 ± .009)

6.35 ± .64

(.250 ± .025)

12.70 ± .64

(.500 ± .025)

.38

(.015)

MIN. STANDOFF

.38

(.015)

MIN. STANDOFF

.38

(.015)

MIN. STANDOFF

.76

(.030)

6.35

(.250)

1/4-32 UNEF-2A

THREADED METAL

BUSHING

MOUNTING

SURFACE

.76 ± .05 X .97

(.030 ± .002 X .038)

ANTI-ROTATION

BOSS

HIGHR

DIA. MOUNTING

SURFACE

7.62

(.300)

.38

(.015)

MIN.

STANDOFF

.51

(.020) 2 PLACES

5.08 ± .51

(.200 ± .020)

BC A

NOTE:

* Only recommended shaft length

for bushingless version

DIMENSIONS: MM

(INCHES)

Specifications are subject to change without notice.

Users should verify actual device performance in their specific applications.

The products described herein and this document are subject to specific legal disclaimers as set forth on the last page of this document, and at www.bourns.com/docs/legal/disclaimer.pdf.

Hardware

LOCKWASHER H-37-5

6.5 ± 0.23

(.256 ± .011)

10.06 ± 0.31

(.396 ± .012)

0.46 ± 0.05

(.018 ± .002)

DIMENSIONS: MM

(INCHES)

NUT H-38-1

9.53 +0/-0.38

(.375 +0/-.015)

11 +0/-0.43

(.433 +0/-.017)

2.36 ± 0.25

(.093 ± .01)

30 ° ± 5 °

TYP.

1/4-32 UNEF

BOURNS COMMON DIMENSIONS 331 03-00; (3531 5] iii an , \ms) 43 w (mg; 5‘105 7 aa \n2n1002y 33 (m5, ‘ ‘ T‘s) E News (”Dr “251m,“ 77,, “2125 [02ﬂ1mmr Wiv 11 g,, 17‘ ¢ 7 36 1 m (T25 N 597159 (WW) .2723? 3:5 (mm may ' ( U ) ﬁg ‘ H7 76 1 DE 54 1 m 7 7[ an 1 mm) 70731 um, \n251 n04] m3,» rm] 7 ﬂ 1 (n 25 1» HUS)

3310 – 9 mm Square Sealed Panel Control

Product Dimensions

DIMENSIONS: MM

(INCHES)

Specifications are subject to change without notice.

Users should verify actual device performance in their specific applications.

The products described herein and this document are subject to specific legal disclaimers as set forth on the last page of this document, and at www.bourns.com/docs/legal/disclaimer.pdf.

COMMON DIMENSIONS

3310H-003

Pot/Switch Dual Cup

Plastic Bushing

3310H-025*

Pot/Pot Dual Cup

Bushingless

Pot/Pot Dual Cup Pot/Switch Dual Cup

Pot Single Cup

3310H-002

Pot/Pot Dual Cup

Metal Bushing

9.53 ± .25

(.375 ± .010)

PRIMARY

ELEMENT

PRIMARY

ELEMENT

SECONDARY

ELEMENT

SWITCH

32 1

BC A

32 1

65 4

PRIMARY

ELEMENT

SECONDARY

ELEMENT

MOUNTING

SURFACE

ANTI-ROTATION LU

1/4-32 UNEF-2A

THREADED

METAL BUSHING

32 1

65 4

2.54 ± .25

(0.10 ± .010)

5.08 ± .25

(0.20 ± .010)

7.54 ± .64

(0.297 ± .025)

12.70 ± .64

(0.50 ± .025)

6.35 ± .08

(0.25 ± .003)

MOUNTING DIA.

5.59 ± .38

(0.220 ± .015)

PRIMARY

WIPER

SECONDARY

CWCCW

CLOCKWISE

PRIMARY

CWCCW

COMMON

SWITCH

CCW

CLOCKWISE

PRIMARY

CWCCW

CLOCKWISE

6.35 ± .08

(0.25 ± .003) MOUNTING DIA.

.36 ± .10

(0.14 ± .004)

12.70 ± .64

(0.50 ± .025)

7.62 ± .64

(0.29 ± .025)

5.97 ± .89

(0.235 ± .035)

.64 ± .10

(.025 ± .004)

ADJ. SLOT DEEPWIDE X .76 ± .08

(.03 ± .004)

.69 ± .10

(.027 ± .004)

ADJ. SLOT DEEPWIDE X .76 ± .08

(.03 ± .004)

5.97 ± .89

(.235 ± .035)

2.54 ± .25

(0.10 ± .010)

3.18 ± .05

(.125 ± .002)

DIA.

9.75 ± .38

(.383 ± .015)

.38

(.015)

MIN.

STANDOFF

.38

(.015)

MIN.

STANDOFF

.38

(.015)

MIN.

STANDOFF

.76

(.03) 6.35

(0.25)

7.62

(0.30) TYP.

1.14

(0.045)TYP.

6.35

(0.25)

.51 ± .05

(.020 ± .002)

TIN PLATED

COPPER PINS

MOUNTING

SURFACE

ANTI-ROTATION LUG

1/4-32 UNEF-2A

THREADED

PLASTIC BUSHING

DIA.

.48

(.019)

4 PLCS.

NOTE: * Only recommended shaft length

for bushingless version

7.62 ± .20

(0.30 ± .008)

MOUNTING

SURFACE

DIA. 3.18 ± .05

(.125 ± .002)

DIA.

REV� 10/20

BOURNS Page hlfQI/A/I/WW.[mum5.Com/IﬁaI/dlsC/almersrtenﬁsindrgu/Icres mtg/MW.boums.cum/docs/Legal/disclaimel Ed!

Legal Disclaimer Notice

This legal disclaimer applies to purchasers and users of Bourns® products manufactured by or on behalf of Bourns, Inc. and

P[ZHɉSPH[LZJVSSLJ[P]LS`¸)V\YUZ¹

Unless otherwise expressly indicated in writing, Bourns® products and data sheets relating thereto are subject to change

^P[OV\[UV[PJL<ZLYZZOV\SKJOLJRMVYHUKVI[HPU[OLSH[LZ[YLSL]HU[PUMVYTH[PVUHUK]LYPM`[OH[Z\JOPUMVYTH[PVUPZJ\YYLU[

and complete before placing orders for Bourns® products.

The characteristics and parameters of a Bourns® product set forth in its data sheet are based on laboratory conditions, and

statements regarding the suitability of products for certain types of applications are based on Bourns’ knowledge of typical

requirements in generic applications. The characteristics and parameters of a Bourns®WYVK\J[PUH\ZLYHWWSPJH[PVUTH`]HY`

MYVT[OLKH[HZOLL[JOHYHJ[LYPZ[PJZHUKWHYHTL[LYZK\L[VP[OLJVTIPUH[PVUVM[OL)V\YUZ® product with other components

PU[OL\ZLY»ZHWWSPJH[PVUVYPP[OLLU]PYVUTLU[VM[OL\ZLYHWWSPJH[PVUP[ZLSM;OLJOHYHJ[LYPZ[PJZHUKWHYHTL[LYZVMH)V\YUZ®

WYVK\J[HSZVJHUHUKKV]HY`PUKPɈLYLU[HWWSPJH[PVUZHUKHJ[\HSWLYMVYTHUJLTH`]HY`V]LY[PTL<ZLYZZOV\SKHS^H`Z]LYPM`

the actual performance of the Bourns®WYVK\J[PU[OLPYZWLJPÄJKL]PJLZHUKHWWSPJH[PVUZHUKTHRL[OLPYV^UPUKLWLUKLU[

Q\KNTLU[ZYLNHYKPUN[OLHTV\U[VMHKKP[PVUHS[LZ[THYNPU[VKLZPNUPU[V[OLPYKL]PJLVYHWWSPJH[PVU[VJVTWLUZH[LMVY

KPɈLYLUJLZIL[^LLUSHIVYH[VY`HUKYLHS^VYSKJVUKP[PVUZ

<USLZZ)V\YUZOHZL_WSPJP[S`KLZPNUH[LKHUPUKP]PK\HS)V\YUZ® product as meeting the requirements of a particular industry

Z[HUKHYKLN0:6;:  VYHWHY[PJ\SHYX\HSPÄJH[PVULN<3SPZ[LKVYYLJVNUPaLK)V\YUZPZUV[YLZWVUZPISLMVYHU`

MHPS\YLVMHUPUKP]PK\HS)V\YUZ®WYVK\J[[VTLL[[OLYLX\PYLTLU[ZVMZ\JOPUK\Z[Y`Z[HUKHYKVYWHY[PJ\SHYX\HSPÄJH[PVU<ZLYZ

of Bourns® products are responsible for ensuring compliance with safety-related requirements and standards applicable to

[OLPYKL]PJLZVYHWWSPJH[PVUZ

Bourns®WYVK\J[ZHYLUV[YLJVTTLUKLKH\[OVYPaLKVYPU[LUKLKMVY\ZLPUU\JSLHYSPMLZH]PUNSPMLJYP[PJHSVYSPMLZ\Z[HPUPUN

HWWSPJH[PVUZUVYPUHU`V[OLYHWWSPJH[PVUZ^OLYLMHPS\YLVYTHSM\UJ[PVUTH`YLZ\S[PUWLYZVUHSPUQ\Y`KLH[OVYZL]LYLWYVWLY[`

VYLU]PYVUTLU[HSKHTHNL<USLZZL_WYLZZS`HUKZWLJPÄJHSS`HWWYV]LKPU^YP[PUNI`[^VH\[OVYPaLK)V\YUZYLWYLZLU[H[P]LZ

on a case-by-case basis, use of any Bourns®WYVK\J[ZPUZ\JO\UH\[OVYPaLKHWWSPJH[PVUZTPNO[UV[ILZHMLHUK[O\ZPZH[

[OL\ZLY»ZZVSLYPZR3PMLJYP[PJHSHWWSPJH[PVUZPUJS\KLKL]PJLZPKLU[PÄLKI`[OL<:-VVKHUK+Y\N(KTPUPZ[YH[PVUHZ*SHZZ000

KL]PJLZHUKNLULYHSS`LX\P]HSLU[JSHZZPÄJH[PVUZV\[ZPKLVM[OL<UP[LK:[H[LZ

)V\YUZL_WYLZZS`PKLU[PÄLZ[OVZL)V\YUZ®Z[HUKHYKWYVK\J[Z[OH[HYLZ\P[HISLMVY\ZLPUH\[VTV[P]LHWWSPJH[PVUZVUZ\JO

WYVK\J[Z»KH[HZOLL[ZPU[OLZLJ[PVULU[P[SLK¸(WWSPJH[PVUZ¹<USLZZL_WYLZZS`HUKZWLJPÄJHSS`HWWYV]LKPU^YP[PUNI`[^V

H\[OVYPaLK)V\YUZYLWYLZLU[H[P]LZVUHJHZLI`JHZLIHZPZ\ZLVMHU`V[OLY)V\YUZ®Z[HUKHYKWYVK\J[ZPUHUH\[VTV[P]L

HWWSPJH[PVUTPNO[UV[ILZHMLHUK[O\ZPZUV[YLJVTTLUKLKH\[OVYPaLKVYPU[LUKLKHUKPZH[[OL\ZLY»ZZVSLYPZR0M)V\YUZ

L_WYLZZS`PKLU[PÄLZHZ\IJH[LNVY`VMH\[VTV[P]LHWWSPJH[PVUPU[OLKH[HZOLL[MVYP[ZZ[HUKHYKWYVK\J[ZZ\JOHZPUMV[HPUTLU[

VYSPNO[PUNZ\JOPKLU[PÄJH[PVUTLHUZ[OH[)V\YUZOHZYL]PL^LKP[ZZ[HUKHYKWYVK\J[HUKOHZKL[LYTPULK[OH[PMZ\JO)V\YUZ®

Z[HUKHYKWYVK\J[PZJVUZPKLYLKMVYWV[LU[PHS\ZLPUH\[VTV[P]LHWWSPJH[PVUZP[ZOV\SKVUS`IL\ZLKPUZ\JOZ\IJH[LNVY`VM

H\[VTV[P]LHWWSPJH[PVUZ(U`YLMLYLUJL[V)V\YUZ®Z[HUKHYKWYVK\J[PU[OLKH[HZOLL[HZJVTWSPHU[^P[O[OL(,*8Z[HUKHYK

VY¸H\[VTV[P]LNYHKL¹KVLZUV[I`P[ZLSMTLHU[OH[)V\YUZOHZHWWYV]LKZ\JOWYVK\J[MVY\ZLPUHUH\[VTV[P]LHWWSPJH[PVU

Bourns®Z[HUKHYKWYVK\J[ZHYLUV[[LZ[LK[VJVTWS`^P[O<UP[LK:[H[LZ-LKLYHS(]PH[PVU(KTPUPZ[YH[PVUZ[HUKHYKZNLULYHSS`

VYHU`V[OLYNLULYHSS`LX\P]HSLU[NV]LYUTLU[HSVYNHUPaH[PVUZ[HUKHYKHWWSPJHISL[VWYVK\J[ZKLZPNULKVYTHU\MHJ[\YLKMVY

\ZLPUHPYJYHM[VYZWHJLHWWSPJH[PVUZ)V\YUZL_WYLZZS`PKLU[PÄLZ)V\YUZ® standard products that are suitable for use in aircraft

VYZWHJLHWWSPJH[PVUZVUZ\JOWYVK\J[Z»KH[HZOLL[ZPU[OLZLJ[PVULU[P[SLK¸(WWSPJH[PVUZ¹<USLZZL_WYLZZS`HUKZWLJPÄJHSS`

HWWYV]LKPU^YP[PUNI`[^VH\[OVYPaLK)V\YUZYLWYLZLU[H[P]LZVUHJHZLI`JHZLIHZPZ\ZLVMHU`V[OLY)V\YUZ® standard

WYVK\J[PUHUHPYJYHM[VYZWHJLHWWSPJH[PVUTPNO[UV[ILZHMLHUK[O\ZPZUV[YLJVTTLUKLKH\[OVYPaLKVYPU[LUKLKHUKPZH[

the user’s sole risk.

;OL\ZLHUKSL]LSVM[LZ[PUNHWWSPJHISL[V)V\YUZ® custom products shall be negotiated on a case-by-case basis by Bourns

and the user for which such Bourns®J\Z[VTWYVK\J[ZHYLZWLJPHSS`KLZPNULK(IZLU[H^YP[[LUHNYLLTLU[IL[^LLU)V\YUZ

HUK[OL\ZLYYLNHYKPUN[OL\ZLHUKSL]LSVMZ\JO[LZ[PUN[OLHIV]LWYV]PZPVUZHWWSPJHISL[V)V\YUZ® standard products shall

also apply to such Bourns® custom products.

Users shall not sell, transfer, export or re-export any Bourns®WYVK\J[ZVY[LJOUVSVN`MVY\ZLPUHJ[P]P[PLZ^OPJOPU]VS]L[OL

KLZPNUKL]LSVWTLU[WYVK\J[PVU\ZLVYZ[VJRWPSPUNVMU\JSLHYJOLTPJHSVYIPVSVNPJHS^LHWVUZVYTPZZPSLZUVYZOHSS[OL`\ZL

Bourns®WYVK\J[ZVY[LJOUVSVN`PUHU`MHJPSP[`^OPJOLUNHNLZPUHJ[P]P[PLZYLSH[PUN[VZ\JOKL]PJLZ;OLMVYLNVPUNYLZ[YPJ[PVUZ

HWWS`[VHSS\ZLZHUKHWWSPJH[PVUZ[OH[]PVSH[LUH[PVUHSVYPU[LYUH[PVUHSWYVOPIP[PVUZPUJS\KPUNLTIHYNVZVYPU[LYUH[PVUHS

YLN\SH[PVUZ-\Y[OLY)V\YUZ® products and Bourns technology and technical data may not under any circumstance be

exported or re-exported to countries subject to international sanctions or embargoes. Bourns® products may not, without

WYPVYH\[OVYPaH[PVUMYVT)V\YUZHUKVY[OL<:.V]LYUTLU[ILYLZVSK[YHUZMLYYLKVYYLL_WVY[LK[VHU`WHY[`UV[LSPNPISL

[VYLJLP]L<:JVTTVKP[PLZZVM[^HYLHUK[LJOUPJHSKH[H

;V[OLTH_PT\TL_[LU[WLYTP[[LKI`HWWSPJHISLSH^)V\YUZKPZJSHPTZPHU`HUKHSSSPHIPSP[`MVYZWLJPHSW\UP[P]LJVUZLX\LU[PHS

PUJPKLU[HSVYPUKPYLJ[KHTHNLZVYSVZ[YL]LU\LZVYSVZ[WYVÄ[ZHUKPPHU`HUKHSSPTWSPLK^HYYHU[PLZPUJS\KPUNPTWSPLK^HYYHU[PLZ

VMÄ[ULZZMVYWHY[PJ\SHYW\YWVZLUVUPUMYPUNLTLU[HUKTLYJOHU[HIPSP[`

)RU\RXUFRQYHQLHQFHFRSLHVRIWKLV/HJDO'LVFODLPHU1RWLFHZLWK*HUPDQ6SDQLVK-DSDQHVH7UDGLWLRQDO&KLQHVHDQG6LPSOLÀHG&KLQHVH

bilingual versions are available at:

Web Page: http://www.bourns.com/legal/disclaimers-terms-and-policies

PDF: http://www.bourns.com/docs/Legal/disclaimer.pdf

*9

3310 Series Datasheet by Bourns Inc.

INFORMATION

HELP

CONTACT US

FOLLOW US