78798-001 Prod Spec Datasheet by Molex

> molexz” C SAS/ PCle RIGHT ANGLE SMT RECEPTACLE Product Name Series Number REVISION. ECR/ECN INFORMATION. TITLE. SHEET No. ECM. DATE. 2.85mm HEIGHT DOCUMENT NUMBER. CREATED / REVISED BY. CHECKED BY. APPROVED BY. PS-78798-001
PRODUCT SPECIFICATION
REVISION:
ECR/ECN INFORMATION:
TITLE:
SAS/ PCIe
RIGHT ANGLE SMT RECEPTACLE
2.85mm HEIGHT
SHEET No.
A
ECM:
109385
1 of 8
DATE:
2016/10/17
CREATED / REVISED BY:
CHECKED BY:
APPROVED BY:
PS-78798-001
SKANG
CWANG25
SHONG
TEMPLATE FILENAME: PRODUCT_SPEC[SIZE_A4](V.1).DOC
SAS/ PCIe RIGHT ANGLE SMT RECEPTACLE
1.0 SCOPE
This Product Specification covers the performance requirements of the SAS/PCIe High Speed
Serialized Receptacle connector.
2.0 PRODUCT DESCRIPTION
2.1 PRODUCT NAME AND SERIES NUMBER(S)
Product Name Series Number
SAS/PCIE, RIGHT ANGLE RECEPTACLE, SMT 78798
2.2 DIMENSIONS, MATERIALS, PLATINGS AND MARKINGS
See the appropriate Sales Drawing for information on dimensions, materials, platings and
markings.
2.3 SAFETY AGENCY APPROVALS
UL FILE : E29179 VOL 10
CSA : 1422869 (LR19980)
TENTATIVE RELEASE:
THIS SPECIFICATION IS BASED ON DESIGN OBJECTIVES AND IS STRICTLY TENTATIVE.
PRELIMINARY TEST DATA MAY EXIST, BUT THIS SPECIFICATION IS SUBJECT TO CHANGE
BASED ON THE RESULTS OF ADDITIONAL TESTING AND EVALUATION.
> molexz” C REVTSION. ECR/ECN INFORMATION. TTTLE. SHEET No. ECM. DATE. 2.85mm HEIGHT DOCUMENT NUMBER. CREATED / REVTSED BY. CHECKED av. APPROVED BY. PS-78798-001
PRODUCT SPECIFICATION
REVISION:
ECR/ECN INFORMATION:
TITLE:
SAS/ PCIe
RIGHT ANGLE SMT RECEPTACLE
2.85mm HEIGHT
SHEET No.
A
ECM:
109385
2 of 8
DATE:
2016/10/17
CREATED / REVISED BY:
CHECKED BY:
APPROVED BY:
PS-78798-001
SKANG
CWANG25
SHONG
TEMPLATE FILENAME: PRODUCT_SPEC[SIZE_A4](V.1).DOC
3.0 APPLICABLE DOCUMENTS AND SPECIFICATIONS
The following documents form a part of this specification to the extend specified herewith. In the
event of conflict between the requirements of this specification and the product drawing, the
product drawing shall take precedence. In addition, in event of conflict between the requirements
of this specification and the referenced documents, this specification shall take precedence.
4.0 RATINGS
4.1 VOLTAGE
30 Volts Max.
4.2 CURRENT
Power section (per pin):
- Continuous Current 1.5A DC
- Peak Current 2.5A for 1.5s
- Peak Current Pre-charge 6A for 1ms
Signal section (per pin):
- Continuous current 500mA
4.3 TEMPERATURE
Operating: 0°C to + 55°C
Non-Operating: -40°C to + 85°C
5.0 PERFORMANCE
5.1 ELECTRICAL REQUIREMENTS
ITEM
DESCRIPTION
TEST CONDITION
REQUIREMENT
1
Low Level Contact
Resistance
(LLCR)
Subject mated contacts assembled in
housing to 20 mV maximum open circuit
at 100 mA maximum.
(EIA 364-23)
45 m MAXIMUM
[Initial]
15 m MAXIMUM
[Delta change from Initial]
> PS-78798-001 e REVTSION. ECR/ECN INFORMATION. TTTLE. SHEET No. ECM. DATE. 2.85mm HEIGHT DOCUMENT NUMBER. CREATED / REVTSED BY. CHECKED av. APPROVED BY.
PRODUCT SPECIFICATION
REVISION:
ECR/ECN INFORMATION:
TITLE:
SAS/ PCIe
RIGHT ANGLE SMT RECEPTACLE
2.85mm HEIGHT
SHEET No.
A
ECM:
109385
3 of 8
DATE:
2016/10/17
CREATED / REVISED BY:
CHECKED BY:
APPROVED BY:
PS-78798-001
SKANG
CWANG25
SHONG
TEMPLATE FILENAME: PRODUCT_SPEC[SIZE_A4](V.1).DOC
2
Temperature Rise
(via current
cycling)
(Power Segment)
Mount connector to a test PCB with ½ oz
copper layer.
Wire power pins P1, P2, P8 and P9 in
parallel for power.
Wire ground pins P4, P5, P6, P10 and
P12 in parallel for return.
Supply 6A total DC current to the power
pins in parallel, returning from the parallel
ground pins.
Measure and record temperature after 96
hours (45 minutes ON and 15 minutes
OFF per hour).
1.5 A per pin
MINIMUM
Temperature rise shall not
exceed 30°C at any point in the
connector when contacts are
powered
Still Air at Ambient temperature
25±3 °C
3
Insulation
Resistance
Subject a voltage of 500 VDC for 1
minute, measure the insulation resistance
between adjacent terminals of the mated
and unmated connector assemblies.
(EIA 364-21)
1000 Megohms
MINIMUM
4
Dielectric
Withstanding
Voltage
Subject a voltage of 500 VAC for
1 minute between adjacent terminals of
mated and unmated connector at sea
level.
(EIA 364-20 Method B)
No breakdown
5.2 MECHANICAL REQUIREMENTS
ITEM
DESCRIPTION
TEST CONDITION
REQUIREMENT
5
Connector Mate
and
Unmate Forces
Mate and Unmate connector assemblies
at a rate of 25.4 mm per minute.
(EIA 364-13)
Mate force - 50 N MAXIMUM
Unmate force - 5 N MINIMUM
[Initial & After durability]
6
Durability
25 cycles for cable application;
500 cycles for backplane application.
All at a maximum rate of 200 cycles/hr.
(EIA 364-09)
No Physical damage
15 m
MAXIMUM
[Delta change from Initial]
7
Terminal Retention
Force
Apply axial pull out force on terminal in the
housing at a rate of 25.4 mm per minute.
Port 1: 3.50 N MINIMUM
Port 2: 2.20 N MINIMUM
[Before and after
Preconditioning]
> PS-78798-001 Insulation Resistance Dielectric Withstanding Voltage REV‘SION. ECR/ECN INFORMATION. T‘TLE. SHEET N0. ECM. DATE. 2.85mm HEIGHT DOCUMENT NUMBER. CREATED / REV‘SED BY. CHECKED EV. APPROVED BY.
PRODUCT SPECIFICATION
REVISION:
ECR/ECN INFORMATION:
TITLE:
SAS/ PCIe
RIGHT ANGLE SMT RECEPTACLE
2.85mm HEIGHT
SHEET No.
A
ECM:
109385
4 of 8
DATE:
2016/10/17
CREATED / REVISED BY:
CHECKED BY:
APPROVED BY:
PS-78798-001
SKANG
CWANG25
SHONG
TEMPLATE FILENAME: PRODUCT_SPEC[SIZE_A4](V.1).DOC
8
Physical Shock
Subject mated connector to 50 g’s
half-sine shock pulses of 11 msec
duration. Three shocks in each direction
applied along three mutually
perpendicular planes for a total of 18
shocks.
(EIA 364-27 Condition A)
Test set-up per Section 8.0
No Physical damage
No discontinuities of 1 s or
longer duration
15 mMAXIMUM
[Delta change from Initial]
9
Random Vibration
Subject mated connector to 3.10 g’s
RMS. 15 minutes in each of the three
mutually perpendicular planes.
(EIA 364-28 Test Condition VII Test letter
D)
Test set-up per Section 8.0
No discontinuities of 1 s or
longer duration
15 mMAXIMUM
[Delta change from Initial]
5.3 ENVIRONMENTAL REQUIREMENTS
ITEM
DESCRIPTION
TEST CONDITION
REQUIREMENT
10
Humidity
Subject the connector to temperature and
humidity of 40°C with 90% to 95% RH for
96 hours.
(EIA 364-31 Method II Test Condition A)
No Physical damage
Insulation Resistance
1000 Megohms
MINIMUM
[Initial & after test]
Dielectric Withstanding
Voltage
No breakdown
11
Solderability
Unmated Connector.
Steam age for 8 hours +/- 15 minutes.
Solder Time: 3 0.5 seconds
Solder Temperature: 260 5°C
Flux type: ROL0
(JESD 22-B-102 Condition C)
95% MININUM
Solder coverage
12
Temperature Life
Subject mated connector to temperature
life at +85°C for 500 hours.
(EIA 364-17 Method A Test Condition 3)
No Physical damage
15 m
MAXIMUM
[Delta change from Initial]
13
Thermal Shock
Subject connector to 10 cycles between
-55°C and +85°C.
(EIA 364-32 Method A Test Condition I)
No Physical damage
> molexz” C REVTSION. ECR/ECN INFORMATION. TTTLE. SHEET No. ECM. DATE. 2.85mm HEIGHT DOCUMENT NUMBER. CREATED / REVTSED BY. CHECKED av. APPROVED BY. PS-78798-001
PRODUCT SPECIFICATION
REVISION:
ECR/ECN INFORMATION:
TITLE:
SAS/ PCIe
RIGHT ANGLE SMT RECEPTACLE
2.85mm HEIGHT
SHEET No.
A
ECM:
109385
5 of 8
DATE:
2016/10/17
CREATED / REVISED BY:
CHECKED BY:
APPROVED BY:
PS-78798-001
SKANG
CWANG25
SHONG
TEMPLATE FILENAME: PRODUCT_SPEC[SIZE_A4](V.1).DOC
14
Mixed Flowing Gas
Subject connector to the following condition:
SO₂ gas concentration: 0.1 ppm.
NO₂ gas concentration: 0.2 ppm.
H₂S gas concentration: 0.01 ppm.
CL₂ gas concentration: 0.01 ppm.
Temperature: 30 ± 1 °C
Relative Humidity: 70 ± 2 %
Half of the samples are exposed unmated
for 7 days, then mated for the remaining 7
days. The other half of the samples mated
for full 14 days test period.
(EIA 364-65, Class IIA)
No Physical damage
15 mMAXIMUM
[Delta change from Initial]
15
Resistance to
Soldering Heat
Refer to Section 9.0 for Soldering profile
No damage in
appearance of connector
6.0 PACKAGING
Parts shall be packaged to protect against damage during handling, transit and storage.
> molex” C REVTSION. ECR/ECN INFORMATION. TTTLE. SHEET No. ECM. DATE. 2.85mm HEIGHT DOCUMENT NUMBER. CREATED / REVTSED BY. CHECKED av. APPROVED BY. PS-78798-001
PRODUCT SPECIFICATION
REVISION:
ECR/ECN INFORMATION:
TITLE:
SAS/ PCIe
RIGHT ANGLE SMT RECEPTACLE
2.85mm HEIGHT
SHEET No.
A
ECM:
109385
6 of 8
DATE:
2016/10/17
CREATED / REVISED BY:
CHECKED BY:
APPROVED BY:
PS-78798-001
SKANG
CWANG25
SHONG
TEMPLATE FILENAME: PRODUCT_SPEC[SIZE_A4](V.1).DOC
7.0 TEST SEQUENCES
Test Group A to E are covered by SAS Specification.
Test Group
A
B
C
D
E
F
G
Test or Examination
Examination of the connector(s)
1,5
1,9
1,8
1,8
1,8
1
Low Level Contact Resistance
(LLCR)
2,4
3,7
2,4,6
2,5,7
Insulation Resistance
2,6
Dielectric Withstanding Voltage
3,7
Current Rating (Temperature Rise)
7
Mate Force
2
Unmate Force
8
Durability
3
4(a)
3(a)
Physical Shock
6
Vibration
5
Humidity
5
Temperature Life
3
Reseating
(manually unplug/plug three times)
5
6
Thermal Shock
4
Mixed Flowing Gas
4
Resistance to Soldering Heat
3
Terminal Retention Force
2,4
Solderability
1
Note – (a) Preconditioning, 50 cycles for the 500-durability cycles requirement. The mate and unmate
cycle is at a maximum rate of 200 cycles per hour.
> molexz” C O O O CO O O .IIHHI‘ O ()0 00 —I U 0 En} 0 o O O O O O O 0 oz '00@ \x O A Momg Rm 3—!— REVISION. ECR/ECN INFORMATION. TITLE. SHEET No. ECM. DATE. 2.85mm HEIGHT DOCUMENT NUMBER. CREATED / REVISED BY. CHECKED BY. APPROVED BY. PS-78798-001
PRODUCT SPECIFICATION
REVISION:
ECR/ECN INFORMATION:
TITLE:
SAS/ PCIe
RIGHT ANGLE SMT RECEPTACLE
2.85mm HEIGHT
SHEET No.
A
ECM:
109385
7 of 8
DATE:
2016/10/17
CREATED / REVISED BY:
CHECKED BY:
APPROVED BY:
PS-78798-001
SKANG
CWANG25
SHONG
TEMPLATE FILENAME: PRODUCT_SPEC[SIZE_A4](V.1).DOC
8.0 VIBRATION/SHOCK TEST SET-UP
SAS/PCIe Receptacle mated with SAS/PCIe Plug (For Reference Only)
SAS/PCIe Receptacle
PC Board
Nut
Angle Plate Fixture
Screw
Vibration / Shock Table
Mounting Fixture
SAS/PCIe Plug
Screw
PC Board
Spacer
> molexz” C Time to Peak Temperature Temp eralure Time at Peak Temperature Peak Temperature Ramp Rate Peak Tern perature —— Cool Dawn Ramp Rate Liqumus Tem perature —— Preheat Temperatule Ramp Rate Time at Prehea‘ Tempera‘ure Preheat Tem peramre —— Time Wlihln 5°C 0' Peak Room Temperature I Time E Time Above : 3‘— Liquidus _>i Temperature REVISION. ECR/ECN INFORMATION. TITLE. SHEET No. ECM. DATE. 2.85mm HEIGHT DOCUMENT NUMBER. CREATED / REVISED BY. CHECKED av. APPROVED BY. PS-78798-001
PRODUCT SPECIFICATION
REVISION:
ECR/ECN INFORMATION:
TITLE:
SAS/ PCIe
RIGHT ANGLE SMT RECEPTACLE
2.85mm HEIGHT
SHEET No.
A
ECM:
109385
8 of 8
DATE:
2016/10/17
CREATED / REVISED BY:
CHECKED BY:
APPROVED BY:
PS-78798-001
SKANG
CWANG25
SHONG
TEMPLATE FILENAME: PRODUCT_SPEC[SIZE_A4](V.1).DOC
9.0 SOLDERING PROFILE
Description
Requirement
Average Ramp Rate
3°C/sec Max
Preheat Temperature
150°C Min to 200°C Max
Preheat Time
60 to 180 sec
Ramp to Peak
3°C/sec Max
Time over Liquidus (217°C)
60 to 150 sec
Peak Temperature
260 +0/-5°C
Time within 5°C of Peak
20 to 40 sec
Ramp - Cool Down
6°C/sec Max
Time 25°C to Peak
8 min Max