Microwave Coaxial Catalog by Murata Electronics Datasheet

Cat.No.O30E-8

Murata

Manufacturing Co., Ltd.

Microwave Coaxial

Connectors

• This PDF catalog is downloaded from the website of Murata Manufacturing co., ltd. Therefore, it’s specifications are subject to change or our products in it may be discontinued without advance notice. Please check with our

sales representatives or product engineers before ordering.

• This PDF catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.

!Note O30E.pdf

07.9.3

for EU RoHS Compliant

• All the products on this catalog are complied with EU RoHS.

• EU RoHS is "the European Directive 2002/95/EC on the Restriction of the Use

of Certain Hazardous Substances in Electrical and Electronic Equipment".

• For more details, please refer to our website 'Murata's Approach for EU RoHS'

(http://www.murata.com/info/rohs.html).

!Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.

• This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.

• This PDF catalog is downloaded from the website of Murata Manufacturing co., ltd. Therefore, it’s specifications are subject to change or our products in it may be discontinued without advance notice. Please check with our

sales representatives or product engineers before ordering.

• This PDF catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.

!Note O30E.pdf

07.9.3

1

2

3

4

5

Part Numbering 2

Microwave Coaxial Connectors with Switch SWF Type 3

Notice 5

Package 8

Microwave Coaxial Connectors with Switch SWD Type 9

Notice 11

Package 14

Ultra Miniature SMT HSC Type 15

Notice 18

Package 21

Miniature SMT GSC Type 22

Notice 25

Package 28

SMT FSC Type 29

Notice 32

Package 35

Miniaturized Microwave Coaxial Connector Cable List 36

1

2

3

4

5

CONTENTS

!Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.

• This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.

• This PDF catalog is downloaded from the website of Murata Manufacturing co., ltd. Therefore, it’s specifications are subject to change or our products in it may be discontinued without advance notice. Please check with our

sales representatives or product engineers before ordering.

• This PDF catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.

!Note O30E.pdf

07.9.3

DCIIED DDDDDD

!Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.

• This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.

oPart Numbering

(Part Number)

qProduct ID

wSeries

Coaxial Connectors (Chip Type Receptacle)

MM Microwave Coaxial Connectors

(Chip Type Receptacle)

Product ID

FSC, SWD, GSC Type 1000pcs. /Reel (ø178mm)

HSC Type, 4000pcs. /Reel (ø178mm)

HSC Type, 10000pcs. /Reel (ø330mm)

SWD Type, 3000pcs. /Reel (ø330mm)

FSC Type, 4000pcs. /Reel (ø330mm)

GSC Type, 5000pcs. /Reel (ø330mm)

SWF Type, 8000pcs. /Reel (ø330mm)

yPackage Detail

A1

A4

B0

B3

B4

B5

B8

Code Package Detail

Bulk

Reel

tPackage Product ID

B

R

Code Package Product ID

HSC Type

FSC Type

SWF Type

SWD Type

GSC Type

4829

7329

8130

8430

9329

Code Series

eIndividual Specification Code (1)

Switch Connector SMD Type

Connector SMD Type

-26

-27

Code Individual Specification Code (1)

rIndividual Specification Code (2)

Serial

00

Code Individual Specification Code (2)

(Part Number)

qProduct ID

wConnector (1)

Coaxial Connectors (with Cable)

MX

Product ID

FSC Type for 76 Cable

FSC Type for 81 Cable

HSC Type

GSC Type

Coaxial Connectors (with Cable)

FG

FK

HP

TK

Code Connector (1)

eCable

0.4D, PFA, Single Shield Line, Spiral

0.8D, FEP, Single Shield Line

0.4D, FEP, Single Shield Line

0.4D, PFA, Single Shield Line, Single Line

0.4D, PFA, Single Shield Line, Spiral

32

76

81

88

92

Code Cable

rConnector (2)

FSC Type for 76 Cable

FSC Type for 81 Cable

HSC Type

GSC Type

None Connector

FG

FK

HP

TK

XX

Code Connector (2)

tLength

yIndividual Specification Code

Expressed by two sign.

y

A1

e

-27

w

7329

r

00

t

R

q

MM

e

76

w

FG

rtyq

MX

Expressed by four figures. The unit is mm. From first to third

figures are significant, and the fourth figure expresses the number

of zeros which follow the three figures.

5000

1001

Ex.)

500mm = 500 x 100

1000mm = 100 x 101

Code Length

• This PDF catalog is downloaded from the website of Murata Manufacturing co., ltd. Therefore, it’s specifications are subject to change or our products in it may be discontinued without advance notice. Please check with our

sales representatives or product engineers before ordering.

• This PDF catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.

!Note O30E.pdf

07.9.3

1

!Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.

• This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.

Microwave Coaxial Connectors

Microwave Coaxial Connectors with Switch SWF Type

■ Features

1. The coaxial connector with switch is very useful

for characteristic measurement Cellular phone

and microwave circuit.

2. It is possible to switch the line connection and

disconnection easily by special probe.

3. Small size, low profile, size 2.5x2.5x1.4mm (LxWxH)

4. Excellent characteristics, low IL 0.2dB max.

V.S.W.R. 1.3 max. Isolation 15dB min. (DC to

6GHz)

5. Surface mountable and reflow solderable

6. Tape package available

■ Applications

Cellular phone, W-LAN, Other wireless and measurement

equipment

C Terminal

Side R Terminal

Side

2.5±0.2

Dia. 2.1±0.2

1.4±0.1

0.8±0.2

2.5±0.2

IN

OUT

GROUND

(in mm)

MM8130-2600

Part Number Rated

Voltage

(Vrms)

Contact

Resistance

(max.) (ohm)

Withstand

Voltage

(Vrms)

Insulation

Resistance

(M ohm)

Durability

(cycles) Frequency

Rating

Temperature

Range

(degree C) VSWR Insertion

Loss (On)

(dB)

Isolation (Off)

(dB) Inner

Electrode (C)

Inner

Electrode (R)

(material)

Outer

Electrode

(material)

MM8130-2600

250 0.07 300 (AC) 500 100 to 6GHz -40 to +85 1.2 max.

(DC to 3GHz) 0.1 max.

(DC to 3GHz) 20 min.

(DC to 3GHz) Stainless Steel

Gold plated Stainless Steel

Gold plated Copper Alloy

Gold plated

Impedance: 50ohm

■ Measurement Probe Dimensions

MM126036

2-Dia. 2.6±0.15

Dia. 19.68±0.2

Dia. 10±0.2

16±0.15

9±0.2

11.85±0.2 21.65±0.3

(13.35)

(4.02)

Dia. 5.4±0.1

Dia. 7±0.1

Dia. 3.8±0.1

(33.5)

(in mm)

SMA-J

MXHS83QE3000

300±4

(32)

(7.1) (26)

3.1±0.1

9±0.2

15.2±0.2

Dia. 3.2±0.1

Dia. 4.3±0.1

Dia. 5.8±0.2

SMA-J

0.8D Cable

(in mm)

Continued on the following page.

• This PDF catalog is downloaded from the website of Murata Manufacturing co., ltd. Therefore, it’s specifications are subject to change or our products in it may be discontinued without advance notice. Please check with our

sales representatives or product engineers before ordering.

• This PDF catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.

!Note O30E.pdf

07.9.3

1

!Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.

• This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.

Continued from the preceding page.

■ Measurement Probe Dimensions

MXHS83QH3000

300±4

(32) (26)

3.1±0.1

13.9±0.2

12±0.2

20.1±0.2

Dia. 3.4±0.1

Dia. 3.2±0.1

Dia. 4.3±0.1

Dia. 5.8±0.2

0.8D Cable SMA-J

(in mm)

■ Structure

OUT

Without Probe

IN OUT

With Probe

Probe

IN

■ Standard Land Dimensions

1. Standard Pattern Dimensions

I/O pattern should be designed to match 50 ohm impedance

circuit.

Typical PCB material is glass epoxy (εr=4.8). Thickness is

1.0mm.

The solder resist should be printed except for the land

pattern on the PCB.

2. Standard Solder Stencil Mask Pattern

Follow standard solder stencil mask pattern to avoid the

possibility of solder being trapped under connector.

(in mm)

Standard Solder Stencil Mask Pattern

(Mask thickness 0.12mm)

Land

Electrode

1.740.5 0.5

0.5

1.3

2.8

4

1.74

2.9

4.14

1.1

2.7

3.44

1.1

2.7

0.28

2.14

2.7

1.3

2.48

• This PDF catalog is downloaded from the website of Murata Manufacturing co., ltd. Therefore, it’s specifications are subject to change or our products in it may be discontinued without advance notice. Please check with our

sales representatives or product engineers before ordering.

• This PDF catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.

!Note O30E.pdf

07.9.3

Notice 1

!Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.

• This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.

■ Notice (Storage and Operating Condition)

1. Environment Conditions

(1) This product is designed for use in electrical

equipment in the environment (temperature,

humidity, atmospheric pressure, etc.)

specified in this approval drawing. It may not

be used in the following environments or under

the following conditions:

(a) Ambient air containing corrosive gas

(Chlorine gas, Hydrogen sulfide gas,

Ammonia gas, Sulfuric acid gas, Nitric

oxide gas, etc.)

(b) Ambient air containing volatile or

combustible gas

(c) In liquid (water, oil, chemical solution,

organic solvents, etc.)

(d) In environments with a high concentration of

airborne particles

(e) In direct sunlight

(f) Dusty conditions

(g) In freezing

(h) Other environments similar to the above

conditions

(2) Contact the manufacturer before using the

product in any of the above environments or

under any of the above conditions.

2. Storage

Store in manufacturer's package or tightly

re-closed box with the following conditions. Use

this product within 6 months after receipt. Check

the terminal solderability before use if the

product has been stored for more than 6 months.

Temperature: -10 to +40 degree C

Humidity: 15 to 85% RH

• This PDF catalog is downloaded from the website of Murata Manufacturing co., ltd. Therefore, it’s specifications are subject to change or our products in it may be discontinued without advance notice. Please check with our

sales representatives or product engineers before ordering.

• This PDF catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.

!Note O30E.pdf

07.9.3

Peak tem

Notice

1

!Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.

• This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.

■ Notice (Soldering and Mounting)

1. Reflow soldering

Soldering must be carried out without exceeding the

allowable soldering temperature and time shown within

the shaded area of Figure "Allowable Temperature and

Time of Reflow Soldering".

In case the soldering is repeated, the maximum time in

Figure "Allowable Temperature and Time of Reflow

Soldering" should be accumulated time. The standard

soldering conditions are shown in Figure "Reflow

Soldering Standard Conditions".

Follow standard solder stencil mask pattern to avoid the

possibility of solder being trapped under connector.

2. Soldering by soldering iron

Soldering by soldering iron should be carried out in

accordance to the following conditions.

Pre-heating Temperature 150D

Time 60 to 120 s.

Soldering Temperature (at the tip of the soldering

iron) less than 350D

Time less than 3 s.

3. We cannot warrant against mishaps caused by any use

of this product that deviates from allowable temperature

and time of reflow soldering.

4. In soldering, do not apply excessive mechanical force to

terminals or leads greater than specified in the drawing.

5. Please note the following in case of soldering terminals

or leads of the product.

(1) Use Rosin based flux, but not with strong acid flux

(Chlorine content should be less than 0.20wt%).

(2) Flux should be thoroughly cleaned from connector to

prevent possible deterioration of electrical

characteristics.

6. Please mount this product at the position so that stress

by wrap and/or bend of the PCB may not apply to it.

7. Please avoid the cleaning of this product.

Allowable Temperature and Time of Reflow Soldering

Reflow Soldering Standard Conditions

260

250

240

230

220

210

200

190

180

240

230

150

100

25

0

Pre-heating 150±20D

Time (sec.)

30 sec. max.

30-50 sec.60-120 sec.

Peak temperature 250±5D

Temperature (D)

Solder: Sn-3.0Ag-0.5Cu

Measuring point of temperature: In-Out Terminals of the Device

Reflow Soldering: Both Convection and Infrared Rays

: Hot Air

: Hot Plate

30 60 90 120 150 180 210 240

Continued on the following page.

• This PDF catalog is downloaded from the website of Murata Manufacturing co., ltd. Therefore, it’s specifications are subject to change or our products in it may be discontinued without advance notice. Please check with our

sales representatives or product engineers before ordering.

• This PDF catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.

!Note O30E.pdf

07.9.3

Notice 1

!Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.

• This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.

Continued from the preceding page.

■ Notice(Handling)

2. L Type Probe with Locking Function

(MXHS83QE3000, MXHS83QH3000)

Do not try to pull the cable, when a connector with a

coaxial cable is handled.

Do not give a twisted torque to the cable and connector.

Mechanical stress:

The stress to the connector should be limited as figure

shown right.

(1) Stress to the housing.

Stress A and B: 0.5N max.

(2) Stress to the outer sleeve.

Stress C: 0.6N max.

Stress D: 0.6N max.

(3) Cable pull strength.

Stress E: 0.5N max.

3. Usage Condition

(1) Do not apply electrical voltage greater than specified

in the catalog. It might cause degradation or

destruction of the product. Even if it endures during a

short time, long time qualification is not guaranteed.

(2) Confirm that product perfomance is not influenced

with any other components or materials which

directly contact products.

4. Handling

Do not apply excessive shock or load to subassembly

products such as soldered printed circuit board in case

handling or transporting.

Mechanical Stress after Engagement

AB

C

D

E

MM8130-2600

PCB

1. Automatic Measurement Probe (MM126036)

Automatic measurement probe (MM126036) should be

used on the condition in Fig. 1 for good connection

without any damages.

The engagement strokes from the flange to the tip of

probe is 18.28mm to 19.78mm with vertical (0+/-2 degree)

direction.

Insertion the Automatic Measurement Probe

(MM126036) in Receptacle (MM8130-2600)

Fig. 1

0±2°

(in mm)

18.28(Minimum Point for Using)

19.78(Maximum Point for Using)

1.5 (Using Range)

• This PDF catalog is downloaded from the website of Murata Manufacturing co., ltd. Therefore, it’s specifications are subject to change or our products in it may be discontinued without advance notice. Please check with our

sales representatives or product engineers before ordering.

• This PDF catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.

!Note O30E.pdf

07.9.3

Package

1

!Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.

• This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.

■ Dimensions of Reel

Part Number

MM8130-2600RB8

Tolerance

A

330

±2.0

B

13

±0.5

C

21

±0.8

D

2

±0.5

N (min.)

Dia. 100

±1.0

W1

9.4

±1.0

W2 (max.)

13.4

±1.0

D

W1

W2

A

N

(in mm)

B

C

■ Dimensions of Taping

A

2.8±0.1 B

2.8±0.1 W

8±0.2 E

1.75±0.1 F

3.5±0.1 K

1.6±0.1

D0

Dia.1.5+0.1

P0

4±0.1 P1

4±0.1 P2

2±0.1 T

0.25±0.05 (in mm)

P2 P0

P1

D0

A

T

K

B

EF

W

5°max. 5°max.

■ Minimum Quantity

MM8130-2600RB8: 330 mm dia.reel/8000 pcs.

MM8130-2600B: Bulk/free

• This PDF catalog is downloaded from the website of Murata Manufacturing co., ltd. Therefore, it’s specifications are subject to change or our products in it may be discontinued without advance notice. Please check with our

sales representatives or product engineers before ordering.

• This PDF catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.

!Note O30E.pdf

07.9.3

IUD P <4>

2

!Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.

• This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.

Microwave Coaxial Connectors

Microwave Coaxial Connectors with Switch SWD Type

■ Features

1. The coaxial connector with switch is very useful

for characteristic measurement of hand held phone

and microwave circuit.

2. It is possible to switch the line connection and

disconnection easily by special probe.

3. Small size, low profile, size 3x3x1.75mm (LxWxH)

4. Excellent characteristics, low IL 0.2dB max.

V.S.W.R. 1.3 max. Isolation 15dB min. (DC to

6GHz)

5. Surface mountable and reflow solderable

6. Tape package available

■ Applications

Cellular phone, W-LAN, Other wireless and measurement

equipment

C Terminal

Side R Terminal

Side

3±0.1

dia 2.1±0.2

1.75±0.15

0.8±0.2

3±0.1

B

A A

IN

OUT

GROUND

(in mm)

Part Number Rated

Voltage

(Vrms)

Contact

Resistance

(max.) (ohm)

Withstand

Voltage

(Vrms)

Insulation

Resistance

(M ohm)

Durability

(cycles) Frequency

Rating

Temperature

Range

(degree C) VSWR Insertion

Loss (On)

(dB)

Isolation (Off)

(dB) Inner

Electrode (C)

Inner

Electrode (R)

(material)

Outer

Electrode

(material)

MM8430-2610

250 0.05 300 (AC) 500 500 to 6GHz -40 to +85 1.2 max.

(DC to 3GHz) 0.1 max.

(DC to 3GHz) 20 min.

(DC to 3GHz) Stainless Steel

Gold plated Copper Alloy

Silver plated

Impedance: 50ohm

■ Measurement Probe Dimensions

MM126036

2-Dia. 2.6±0.15

Dia.19.68

±0.2

Dia. 10±0.2

16±0.15

9±0.2

11.85±0.2 21.65±0.3

(13.35)

(4.02)

Dia. 5.4±0.1

Dia. 7±0.1

Dia. 3.8±0.1

(33.5)

(in mm)

SMA-J

MXHS83QE3000

300±4

(32)

(7.1) (26)

3.1±0.1

9±0.2

15.2±0.2

Dia. 3.2±0.1

Dia. 4.3±0.1

Dia. 5.8±0.2

SMA-J

0.8D Cable

(in mm)

Continued on the following page.

MM8430-2610

• This PDF catalog is downloaded from the website of Murata Manufacturing co., ltd. Therefore, it’s specifications are subject to change or our products in it may be discontinued without advance notice. Please check with our

sales representatives or product engineers before ordering.

• This PDF catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.

!Note O30E.pdf

07.9.3

EU

2

!Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.

• This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.

Continued from the preceding page.

■ Measurement Probe Dimensions

300±4

(32) (26)

3.1±0.1

13.9±0.2

12±0.2

20.1±0.2

Dia. 3.4±0.1

Dia. 3.2±0.1

Dia. 4.3±0.1

Dia. 5.8±0.2

0.8D Cable SMA-J

(in mm)

■ Structure

OUT

Without Probe

IN OUT

With Probe

Probe

IN

■ Standard Land Dimensions

1. Standard pattern dimensions

I/O pattern should be designed to match 50 ohm impedance

circuit.

Typical PCB material is glass epoxy (εr=4.8). Thickness is

1.0mm.

The solder resist should be printed except for the land

pattern on the PCB.

2. Standard solder stencil mask pattern

Follow Standard solder stencil mask pattern to avoid the

possibility of solder being trapped under connector.

4

2

1

0.5

(1.5)

Land

Electrode

(1.5)

1.74

1

3

2.1

3.1

4.1

Through hole

(in mm)

0.5

2

3.5

2.3

1

3

3.5

The Standard solder stencil mask pattern

(Mask thickness 0.15mm)

MXHS83QH3000

• This PDF catalog is downloaded from the website of Murata Manufacturing co., ltd. Therefore, it’s specifications are subject to change or our products in it may be discontinued without advance notice. Please check with our

sales representatives or product engineers before ordering.

• This PDF catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.

!Note O30E.pdf

07.9.3

Notice

2

!Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.

• This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.

■ Notice (Storage and Operating Condition)

1. Environment Conditions

(1) This product is designed for use in electrical

equipment in the environment (temperature,

humidity, atmospheric pressure, etc.)

specified in this approval drawing. It may not

be used in the following environments or under

the following conditions:

(a) Ambient air containing corrosive gas

(Chlorine gas, Hydrogen sulfide gas,

Ammonia gas, Sulfuric acid gas, Nitric

oxide gas, etc.)

(b) Ambient air containing volatile or

combustible gas

(c) In liquid (water, oil, chemical solution,

organic solvents, etc.)

(d) In environments with a high concentration of

airborne particles

(e) In direct sunlight

(f) Dusty conditions

(g) In freezing

(h) Other environments similar to the above

conditions

(2) Contact the manufacturer before using the

product in any of the above environments or

under any of the above conditions.

2. Storage

Store in manufacturer's package or tightly

re-closed box with the following conditions. Use

this product within 6 months after receipt. Check

the terminal solderability before use if the

product has been stored for more than 6 months.

Temperature: -10 to +40 degree C

Humidity: 15 to 85% RH

• This PDF catalog is downloaded from the website of Murata Manufacturing co., ltd. Therefore, it’s specifications are subject to change or our products in it may be discontinued without advance notice. Please check with our

sales representatives or product engineers before ordering.

• This PDF catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.

!Note O30E.pdf

07.9.3

Peak tem

Notice

2

!Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.

• This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.

■ Notice (Soldering and Mounting)

1. Reflow soldering

Soldering must be carried out without exceeding the

allowable soldering temperature and time shown within

the shaded area of Figure "Allowable Temperature and

Time of Reflow Soldering".

In case the soldering is repeated, the maximum time in

Figure "Allowable Temperature and Time of Reflow

Soldering" should be accumulated time. The standard

soldering conditions are shown in Figure "Reflow

Soldering Standard Conditions".

Follow standard solder stencil mask pattern to avoid the

possibility of solder being trapped under connector.

2. Soldering by soldering iron

Soldering by soldering iron should be carried out in

accordance to the following conditions.

Pre-heating Temperature 150D

Time 60 to 120 s.

Soldering Temperature (at the tip of the soldering

iron) less than 350D

Time less than 3 s.

3. We cannot warrant against mishaps caused by any use

of this product that deviates from allowable temperature

and time of reflow soldering.

4. In soldering, do not apply excessive mechanical force to

terminals or leads greater than specified in the drawing.

5. Please note the following in case of soldering terminals

or leads of the product.

(1) Use Rosin based flux, but not with strong acid flux

(Chlorine content should be less than 0.20wt%).

(2) Flux should be thoroughly cleaned from connector to

prevent possible deterioration of electrical

characteristics.

6. Please mount this product at the position so that stress

by wrap and/or bend of the PCB may not apply to it.

7. Please avoid the cleaning of this product.

Allowable Temperature and Time of Reflow Soldering

Reflow Soldering Standard Conditions

260

250

240

230

220

210

200

190

180

240

230

150

100

25

0

Pre-heating 150±20D

Time (sec.)

30 sec. max.

30-50 sec.60-120 sec.

Peak temperature 250±5D

Temperature (D)

Solder: Sn-3.0Ag-0.5Cu

Measuring point of temperature: In-Out Terminals of the Device

Reflow Soldering: Both Convection and Infrared Rays

: Hot Air

: Hot Plate

30 60 90 120 150 180 210 240

Continued on the following page.

• This PDF catalog is downloaded from the website of Murata Manufacturing co., ltd. Therefore, it’s specifications are subject to change or our products in it may be discontinued without advance notice. Please check with our

sales representatives or product engineers before ordering.

• This PDF catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.

!Note O30E.pdf

07.9.3

El.

Notice

2

!Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.

• This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.

Continued from the preceding page.

2. L Type Probe with Locking Function

(MXHS83QE3000, MXHS83QH3000)

Avoid pulling cable when probe is locked into connector.

Avoid twisting probe or cable when engaging or

disengaging from connector.

Mechanical stress:

The stress to the connector should be limited as figure

shown right.

(1) Stress to the housing.

Stress A and B: 0.5N max.

(2) Stress to the outer sleeve.

Stress C: 0.6N max.

Stress D: 0.6N max.

(3) Cable pull strength.

Stress E: 0.5N max.

3. Usage Condition

(1) Do not apply electrical voltage greater than specified

in the catalog. It might cause degradation or

destruction of the product. Even if it endures during a

short time, long time qualification is not guaranteed.

(2) Confirm that product performance is not influenced

with any other components or materials which

directly contact products.

4. Handling

Avoid excessive stress when handling and transporting

printed circuit board after connector and/or assembly

has been secured to PCB.

Mechanical stress after engagement

AB

C

D

E

MM8430-2610

PCB

Notice (Handling)

1. Automatic Measurement Probe (MM126036)

Automatic measurement probe (MM126036) should be

used under conditions in Fig. 1 for good connection

without any damages.

The engagement strokes from the flange to the tip of

probe is 18.28mm to 19.78mm with vertical (0±2°)

direction.

Insertion the Automatic Measurement Probe

(MM126036) in Receptacle (MM8430-2610)

Fig. 1

0±2°

18.28(Minimum Point for Using)

19.78(Maximum Point for Using)

1.5 (Using Range)

• This PDF catalog is downloaded from the website of Murata Manufacturing co., ltd. Therefore, it’s specifications are subject to change or our products in it may be discontinued without advance notice. Please check with our

sales representatives or product engineers before ordering.

• This PDF catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.

!Note O30E.pdf

07.9.3

Package

2

!Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.

• This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.

■ Dimensions of Reel

Murata Part Number

MM8430-2610RA1

MM8430-2610RB3

TOLERANCE

A

178

330

±2.0

B

13

±0.5

C

21

±0.8

D

2

±0.5

N (min.)

Dia. 50

–

W1

13.5

±1.5

W2 (max.)

18.5

–

DBW1

W2

C

A

N

(in mm)

■ Dimensions of Taping

A

3.4±0.1

B

3.4±0.1

W

12±0.2

E

1.75±0.1

F

5.5±0.1

K

2.0±0.15

D0

Dia.1.5+0.1

P0

4±0.1

P1

8±0.1

P2

2±0.1

T

0.3±0.05

P2 P0 D0 T

B

EF

W

P1 A K

(in mm)

3 degree Max.3 degree Max.

■ Minimum Quantity

MM8430-2610RA1: dia.180 mm reel/1000 pcs.

MM8430-2610RB3: dia.330 mm reel/3000 pcs.

MM8430-2610B: Bulk/free

• This PDF catalog is downloaded from the website of Murata Manufacturing co., ltd. Therefore, it’s specifications are subject to change or our products in it may be discontinued without advance notice. Please check with our

sales representatives or product engineers before ordering.

• This PDF catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.

!Note O30E.pdf

07.9.3

3

!Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.

• This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.

Microwave Coaxial Connectors

Ultra Miniature SMT HSC Type

■ Features

1. The mating height is only 1.2mm maximum by new

mechanical design. Suitable for low profile design.

2. New mating mechanical desigh makes stable feeling

connection.

3. Soft and ultra thin 0.81mm diameter flexible coaxial

cables is available.

4. High performance with wide frequency range(DC to

6GHz). VSWR at 3GHz to 6GHz is 1.45 maximum.

■ Applications

Portable telephone, cordless telephone(analog and

digital), GPS, and other microwave radio and

measurement equipment.

2.06

0.85

(2.1 dia.)

2.34±0.5

(in mm)

MXHP

2

0.6

1.5 Dia.

0.8 Dia.

0.7 0.4

1.4

0.5

1.52

Tolerances Unless

Otherwise Specified: ±0.2

(in mm)

Hot Terminal

Ground Terminal

MM4829-2702

Part Number Rated

Voltage

(V)

Contact

Resistance (max.)

(ohm)

Withstanding

Voltage

(rms)

Insulation

Resistance (min.)

(M ohm)

Durability

(cycles)

Frequency

Rating

(GHz)

Temperature

Range

(degree C) VSWR Center Contact Outer Contact Insulator

MM4829-2702

250 0.020 300 (AC) 500 30 to 6.0 -40 to +85 1.3 max.

(DC to 3GHz) Copper Alloy

Gold plated Copper Alloy

Silver plated Engineering plastic

Impedance: 50ohm

■ Measurement Adapter Dimensions (for Receptacle)

SMA-J

Dia. 5.33±0.2

13.3±0.15

(4.3)

2±0.1

HSC-Female

Dia. 2.5±0.1

Dia. 3.0±0.1

Dia. 5.33±0.1

MM121490 (Hand measurement)

17.96±0.2

2±0.2 7.91±0.1

5.65±0.1

SMA-J

HSC-CONTACT

(in mm)

Dia. 3±0.1

Dia. 5.33±0.1

Dia. 6.5±0.2

Dia. 5.33±0.2

MM121491 (Automatic measurement)

• This PDF catalog is downloaded from the website of Murata Manufacturing co., ltd. Therefore, it’s specifications are subject to change or our products in it may be discontinued without advance notice. Please check with our

sales representatives or product engineers before ordering.

• This PDF catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.

!Note O30E.pdf

07.9.3

3

!Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.

• This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.

MM121500 (Hand measurement)

12.95±0.2

8.55±0.4 0.4±0.05

Dia. 5.33±0.2

Dia. 1.5±0.02

SMA-J

HSC-Male

(in mm)

■ Cable Length Tolerance

20

100

Over

500

1000

100

Cable Length L (mm) Dimensional

Tolerance (mm)

500

Less than

1000

–

±3

±4

±10

+2% of L

–0% of L

L

■ Disengagement Tool (Part Number: M19100)

6.0 45

35 3

2.9

5

HSC

Dia. 2.7

(in mm)

■ Profile Dimensions

1.85 max.

1.2 max.

(in mm)

Continued on the following page.

■

Measurement Adapter Dimensions (for Cable Assembly)

• This PDF catalog is downloaded from the website of Murata Manufacturing co., ltd. Therefore, it’s specifications are subject to change or our products in it may be discontinued without advance notice. Please check with our

sales representatives or product engineers before ordering.

• This PDF catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.

!Note O30E.pdf

07.9.3

Gmund

3

!Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.

• This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.

Continued from the preceding page.

■ Land Pattern Dimensions

1. Standard pattern dimensions

I/O pattern should be designed to match 50 ohm impedance

circuit.

Typical PCB material is glass epoxy (εr=4.8). Thickness is

1.0mm.

The solder resist should be printed except for the land

pattern on the PCB.

2. Standard solder stencil mask pattern

Follow Standard solder stencil mask pattern to avoid the

possibility of solder being trapped under connector.

(in mm)

The standard solder stencil mask drawing

(Mask thickness 0.12mm)

2.5

1.5

1.34 0.5

0.7 0.75

1.25 1.25

(1.81)

1.58 0.54

0.38

0.6

(1.5)

(1.74)

(1.5) Land

Electrode

2.5

1.5 0.38

2.4

0.9

0.84 0.82

0.36

Ground

Hot

• This PDF catalog is downloaded from the website of Murata Manufacturing co., ltd. Therefore, it’s specifications are subject to change or our products in it may be discontinued without advance notice. Please check with our

sales representatives or product engineers before ordering.

• This PDF catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.

!Note O30E.pdf

07.9.3

Notice

3

!Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.

• This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.

■ Notice (Storage and Operation Condition)

1. Environment Conditions

(1) This product is designed for use in electrical

equipment in the environment (temperature,

humidity, atmospheric pressure, etc.)

specified in this approval drawing. It may not

be used in the following environments or under

the following conditions:

(a) Ambient air containing corrosive gas

(Chlorine gas, Hydrogen sulfide gas,

Ammonia gas, Sulfuric acid gas, Nitric

oxide gas, etc.)

(b) Ambient air containing volatile or

combustible gas

(c) In liquid (water, oil, chemical solution,

organic solvents, etc.)

(d) In environments with a high concentration of

airborne particles

(e) In direct sunlight

(f) Dusty conditions

(g) In freezing

(h) Other environments similar to the above

conditions

(2) Contact the manufacturer before using the

product in any of the above environments or

under any of the above conditions.

2. Storage

Store in manufacturer's package or tightly

re-closed box with the following conditions. Use

this product within 6 months after receipt. Check

the terminal solderability before use if the

product has been stored for more than 6 months.

Temperature: -10 to +40 degree C

Humidity: 15 to 85% RH

• This PDF catalog is downloaded from the website of Murata Manufacturing co., ltd. Therefore, it’s specifications are subject to change or our products in it may be discontinued without advance notice. Please check with our

sales representatives or product engineers before ordering.

• This PDF catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.

!Note O30E.pdf

07.9.3

Peak «em :5: W» d

Notice

3

!Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.

• This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.

■ Notice (Soldering and Mounting)

1. Reflow soldering

Soldering must be carried out without exceeding the

allowable soldering temperature and time shown within

the shaded area of Figure "Allowable Temperature and

Time of Reflow Soldering".

In case the soldering is repeated, the maximum time in

Figure "Allowable Temperature and Time of Reflow

Soldering" should be accumulated time. The standard

soldering conditions are shown in Figure "Reflow

Soldering Standard Conditions".

Use the Pattern and Metal mask pattern is illustrated in

details.

Follow standard solder stencil mask pattern to avoid the

possibility of solder being trapped under connector.

2. Soldering by soldering iron

Soldering by soldering iron should be carried out in

accordance to the following conditions.

Pre-heating Temperature 150D

Time 60 to 120 s.

Soldering Temperature (at the tip of the soldering

iron) less than 350D

Time less than 3 s.

3. We cannot warrant against mishaps caused by any use

of this product that deviates from allowable temperature

and time of reflow soldering.

4. In soldering, do not apply excessive mechanical force to

terminals or leads greater than specified in the drawing.

5. Please note the following in case of soldering terminals

or leads of the product.

(1) Use Rosin based flux, but not with strong acid flux

(Chlorine content should be less than 0.20wt%).

(2) Flux should be thoroughly cleaned from connector

to prevent possible deterioration of electrical

characteristics.

6. Please mount this product at the position so that stress

by wrap and/or bend of the PCB may not apply to it.

7. Please dry out this product immediately after soldering

and cleaning.

Allowable Temperature and Time of Reflow Soldering

Reflow Soldering Standard Conditions

260

250

240

230

220

210

200

190

180

240

230

150

100

25

0

Pre-heating 150±20D

Time (sec.)

30 sec. max.

30-50 sec.60-120 sec.

Peak temperature 250±5D

Temperature (D)

Solder : Sn-3.0Ag-0.5Cu

Measuring point of temperature : In-Out Terminals of the Device

Reflow Soldering : Both Convection and Infrared Rays

: Hot Air

: Hot Plate

30 60 90 120 150 180 210 240

Continued on the following page.

• This PDF catalog is downloaded from the website of Murata Manufacturing co., ltd. Therefore, it’s specifications are subject to change or our products in it may be discontinued without advance notice. Please check with our

sales representatives or product engineers before ordering.

• This PDF catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.

!Note O30E.pdf

07.9.3

Notice

3

!Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.

• This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.

Continued from the preceding page.

■ Notice (Handling)

A

B

C

E

D

1. Usage Condition

(1) Do not apply electrical voltage greater than specified in

the drawing. It might cause degradation or destruction

of the product. Even if it endures during a short time,

long time qualification is not guaranteed.

(2) Confirm product's performance is not influenced by

contact of other components.

(3) Please contact the manufacturer beforehand, if the

product is to be used in frequently bent position.

2. Handling

(1) Avoid excessive stress when handling and transporting

printed circuit board after connector and/or assembly

has been secured to PCB.

(2) Do not try to pull the cable, when a connector with a

coaxial cable is handled.

(3) Disregarding the following notes could cause

mechanical damage and/or poor electrical performance.

3. Handling Instructions

(1) Cable is designed to fit only with MM4829-2702

receptacle. Any other receptacle cannot be used with

this cable.

(2) Disengagement:

Use tool P/N M19100 to insert or remove cable in a

vertical direction from receptacle. Avoid pulling only the

cable to prevent cable damage.

(3) Avoid twisting probe or cable when engaging or

disengaging from connector.

(4) Mechanical stress:

The stress to the connector should be limited as shown

in Figure 1.

(a) Stress to the housing.

Stress A and B: 5.0N max.

(b) Stress to the outer sleeve.

Stress C: 1.0N max.

Stress D: 1.0N max.

(c) Cable pull strength.

Stress E: 5.0N max.

Figure 1. Mechanical stress after engagement

• This PDF catalog is downloaded from the website of Murata Manufacturing co., ltd. Therefore, it’s specifications are subject to change or our products in it may be discontinued without advance notice. Please check with our

sales representatives or product engineers before ordering.

• This PDF catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.

!Note O30E.pdf

07.9.3

| I

Package

3

!Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.

• This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.

■ Dimensions of Reel

Murata Part Number

MM4829-2702RA4

MM4829-2702RB0

TOLERANCE

A

180 +0/-3

330

±2.0

B

13

±0.2

C

21

±0.8

D

2

±0.5

N (min.)

Dia. 60 +1/0

Dia. 100

±1.0

W1

9±0.3

9.4

±1.0

W2 (max.)

11.4

13.4

±1.0

B

C

D

W1

W2

N

A

(in mm)

■ Dimensions of Taping

A

2.35±0.1

B

2.35±0.1

W

8±0.2

E

1.75±0.1

F

3.5±0.1

K

0.75±0.15

D0

Dia.1.5 +0.1

-0

P0

4±0.1

P1

4±0.1

P2

2±0.1

T

0.25±0.05

P2 P0 D0 T

B

EF

W

P1 A K

(in mm)

3°max.

■ Minimum Quantity

MM4829-2702RA4: 180 mm dia. reel/4000 pcs.

MM4829-2702RB0: 330 mm dia. reel/10000 pcs.

MM4829-2702B: Bulk/free

• This PDF catalog is downloaded from the website of Murata Manufacturing co., ltd. Therefore, it’s specifications are subject to change or our products in it may be discontinued without advance notice. Please check with our

sales representatives or product engineers before ordering.

• This PDF catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.

!Note O30E.pdf

07.9.3

4

!Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.

• This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.

Microwave Coaxial Connectors

Miniature SMT GSC Type

■ Features

1. The mating height is only 2mm maximum by new

mechanical design. Suitable for low profile design.

2. New mating mechanical desigh makes stable feeling

connection.

3. Soft and ultra thin 0.8mm diameter flexible coaxial

cables is available.

4. High performance with wide frequency range(DC to

6GHz). VSWR at DC to 3GHz is 1.2 maximum. VSWR at

3GHz to 6GHz is 1.3 maximum.

■ Applications

Portable telephone, cordless telephone(analog and

digital), GPS, and other microwave radio and

measurement equipment.

ø2.55 1.5 2.8

3.5±0.5

(in mm)

Tolerances unless

otherwise specified : ±0.3

MXTK

0.15±0.03

(R0.15)

2.6

3

(R0.15)

2.6

30.12±0.03

Hot Terminal

Ground Terminal

0.5±0.1

ø1±0.1

2.1

2.3

0.5±0.1

0.15±0.03

ø2.1

1.15

Tolerances Unless

Otherwise Specified: ±0.2

(in mm)

MM9329-2700

Part Number Rated

Voltage

(V)

Contact

Resistance (max.)

(ohm)

Withstanding

Voltage

(rms)

Insulation

Resistance (min.)

(M ohm)

Durability

(cycles)

Frequency

Rating

(GHz)

Temperature

Range

(degree C) VSWR Center Contact Outer Contact Insulator

MM9329-2700

250 0.015 300 (AC) 500 100 to 6.0 -40 to +90 1.2 max.

(DC to 3GHz) Copper Alloy

Gold plated Copper Alloy

Silver plated Engineering plastic

Impedance: 50ohm

■ Measurement Adapter Dimensions (for Receptacle)

(in mm)

MM121470 (Hand measurement) MM121471 (Automatic measurement)

SMA-JACK

13.4

5.08 7.4

4.4

2.1

ø5.33

ø2.55

ø3

ø4.6

SMA-JACK

18.24

5.08 2 8.19

2.3

ø5.33

ø6.5

ø4.06

ø5.33

Continued on the following page.

• This PDF catalog is downloaded from the website of Murata Manufacturing co., ltd. Therefore, it’s specifications are subject to change or our products in it may be discontinued without advance notice. Please check with our

sales representatives or product engineers before ordering.

• This PDF catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.

!Note O30E.pdf

07.9.3

4

!Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.

• This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.

Continued from the preceding page.

SMA-JACK

13.4

8.55

5.08

0.85

ø2.1

ø5.33

MM121480

(in mm)

■ Cable Length Tolerance

L

40

100

Over

500

1000

100

Cable Length L (mm) (∗)

∗L must be 20mm Min.

Dimensional

tolerance (mm)

500

Till

1000

–

±3

±4

±10

+2% of L

–0% of L

■ Disengagement Tool (Part Number: M22001)

3.9±0.6

2.3±0.6

0.5±0.6

45±2

35±27.95±2

(Dia. 8)

(C1)

(in mm)

■ Profile Dimensions

2.8 max.2max.

0.7 min.

(in mm)

Continued on the following page.

■

Measurement Adapter Dimensions (for Cable Assembly)

• This PDF catalog is downloaded from the website of Murata Manufacturing co., ltd. Therefore, it’s specifications are subject to change or our products in it may be discontinued without advance notice. Please check with our

sales representatives or product engineers before ordering.

• This PDF catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.

!Note O30E.pdf

07.9.3

4

!Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.

• This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.

Continued from the preceding page.

■ Land Pattern Dimensions

1. Standard pattern dimensions

I/O pattern should be designed to match 50 ohm impedance

circuit.

Typical PCB material is glass epoxy (εr=4.8). Thickness is

1.0mm

The solder resist should be printed except for the land

pattern on the PCB.

2. Standard solder stencil mask pattern

Follow Standard solder stencil mask pattern to avoid the

possibility of solder being trapped under connector.

(in mm)

The standard solder stencil mask drawing

(Mask thickness 0.15mm)

21.9

(2.37) 2.5

1.51.5

1.05 1.05

ø1 (3-ø0.6)

(Through Holes)

5.2

3.8

2.3

1

0.6

(1.5)(1.74)(1.5)

0.6

1.5

1.05 1.05 0.45

0.6

2.3

3.3

Land

Electrode

• This PDF catalog is downloaded from the website of Murata Manufacturing co., ltd. Therefore, it’s specifications are subject to change or our products in it may be discontinued without advance notice. Please check with our

sales representatives or product engineers before ordering.

• This PDF catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.

!Note O30E.pdf

07.9.3

Notice

4

!Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.

• This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.

■ Notice (Storage and Operation Condition)

1. Environment Conditions

(1) This product is designed for use in electrical

equipment in the environment (temperature,

humidity, atmospheric pressure, etc.)

specified in this approval drawing. It may not

be used in the following environments or under

the following conditions:

(a) Ambient air containing corrosive gas

(Chlorine gas, Hydrogen sulfide gas,

Ammonia gas, Sulfuric acid gas, Nitric

oxide gas, etc.)

(b) Ambient air containing volatile or

combustible gas

(c) In liquid (water, oil, chemical solution,

organic solvents, etc.)

(d) In environments with a high concentration of

airborne particles

(e) In direct sunlight

(f) Dusty conditions

(g) In freezing

(h) Other environments similar to the above

conditions

(2) Contact the manufacturer before using the

product in any of the above environments or

under any of the above conditions.

2. Storage

Store in manufacturer's package or tightly

re-closed box with the following conditions. Use

this product within 6 months after receipt. Check

the terminal solderability before use if the

product has been stored for more than 6 months.

Temperature: -10 to +40 degree C

Humidity: 15 to 85% RH

• This PDF catalog is downloaded from the website of Murata Manufacturing co., ltd. Therefore, it’s specifications are subject to change or our products in it may be discontinued without advance notice. Please check with our

sales representatives or product engineers before ordering.

• This PDF catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.

!Note O30E.pdf

07.9.3

Peak «em

Notice

4

!Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.

• This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.

■ Notice (Soldering and Mounting)

1. Reflow soldering

Soldering must be carried out without exceeding the

allowable soldering temperature and time shown within

the shaded area of Figure "Allowable Temperature and

Time of Reflow Soldering".

In case the soldering is repeated, the maximum time in

Figure "Allowable Temperature and Time of Reflow

Soldering" should be accumulated time. The standard

soldering conditions are shown in Figure "Reflow

Soldering Standard Conditions".

Follow recommended solder stencil mask pattern to

avoid the possibility of solder being trapped under

connector.

2. Soldering by soldering iron

Soldering by soldering iron should be carried out in

accordance to the following conditions.

Pre-heating Temperature 150D

Time 60 to 120 s.

Soldering Temperature (at the tip of the soldering

iron) less than 350D

Time less than 3 s.

3. We cannot warrant against mishaps caused by any use

of this product that deviates from allowable temperature

and time of reflow soldering.

4. In soldering, do not apply excessive mechanical force to

terminals or leads greater than specified in the drawing.

5. Please note the following in case of soldering terminals

or leads of the product.

(1) Use Rosin based flux, but not with strong acid flux

(Chlorine content should be less than 0.20wt%).

(2) Flux should be thoroughly cleaned from connector

to prevent possible deterioration of electrical

characteristics.

6. Please mount this product at the position so that stress

by wrap and/or bend of the PCB may not apply to it.

7. Please dry out this product immediately after soldering

and cleaning.

Allowable Temperature and Time of Reflow Soldering

Reflow Soldering Standard Conditions

260

250

240

230

220

210

200

190

180

240

230

150

100

25

0

Pre-heating 150±20D

Time (sec.)

30 sec. max.

30-50 sec.60-120 sec.

Peak temperature 250±5D

Temperature (D)

Solder : Sn-3.0Ag-0.5Cu

Measuring point of temperature : In-Out Terminals of the Device

Reflow Soldering : Both Convection and Infrared Rays

: Hot Air

: Hot Plate

30 60 90 120 150 180 210 240

Continued on the following page.

• This PDF catalog is downloaded from the website of Murata Manufacturing co., ltd. Therefore, it’s specifications are subject to change or our products in it may be discontinued without advance notice. Please check with our

sales representatives or product engineers before ordering.

• This PDF catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.

!Note O30E.pdf

07.9.3

Notice

4

!Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.

• This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.

Continued from the preceding page.

■ Notice (Handling)

1. Usage Condition

(1) Do not apply electrical voltage greater than specified in

the drawing. It might cause degradation or destruction

of the product. Even if it endures during a short time,

long time qualification is not guaranteed.

(2) Confirm product's performance is not influenced by

contact of other components.

(3) Please contact the manufacturer beforehand, if the

product is to be used in frequently bent position.

2. Handling

(1) Avoid excessive stress when handling and transporting

printed circuit board after connector and/or assembly

has been secured to PCB.

(2) Do not try to pull the cable, when a connector with a

coaxial cable is handled.

(3) Disregarding the following notes could cause

mechanical damage and/or poor electrical performance.

3. Handling Instructions

(1) Cable is designed to fit only with MM9329-2700

receptacle. Any other receptacle cannot be used with

this cable.

(2) Disengagement:

Use tool P/N M22001 to insert or remove cable in a

vertical direction from receptacle. Avoid pulling only the

cable to prevent cable damage.

(3) Avoid twisting probe or cable when engaging or

disengaging from connector.

(4) Mechanical stress:

The stress to the connector should be limited as shown

in Figure 1.

(a) Stress to the housing.

Stress A and B: 5.0N max.

(b) Stress to the outer sleeve.

Stress C: 3.0N max.

Stress D: 2.0N max.

(c) Cable pull strength.

Stress E: 5.0N max.

Figure 1. Mechanical Stress after Engagement

A

B

C

D

E

• This PDF catalog is downloaded from the website of Murata Manufacturing co., ltd. Therefore, it’s specifications are subject to change or our products in it may be discontinued without advance notice. Please check with our

sales representatives or product engineers before ordering.

• This PDF catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.

!Note O30E.pdf

07.9.3

Package

4

!Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.

• This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.

■ Dimensions of Reel

Murata Part Number

MM9329-2700RA1

MM9329-2700RB5

TOLERANCE

A

178

330

±2.0

B

13

±0.5

C

21

±0.8

D

2

±0.5

N (min.)

Dia. 50

–

W1

13.5

±1.5

W2 (max.)

18.5

–

DBW1

W2

C

A

N

(in mm)

■ Dimensions of Taping

A

3.4±0.1

B

3.4±0.1

W

12±0.2

E

1.75±0.1

F

5.5±0.1

K

1.25±0.15

D0

Dia.1.5 +0.1

-0

P0

4±0.1

P1

8±0.1

P2

2±0.1

T

0.3±0.05

P2 P0 D0 T

B

EF

W

P1 A K

(in mm)

3°max.3°max.

■ Minimum Quantity

MM9329-2700RA1: dia.180 mm reel/1000 pcs.

MM9329-2700RB5: dia.330 mm reel/5000 pcs.

MM9329-2700B: Bulk/free

• This PDF catalog is downloaded from the website of Murata Manufacturing co., ltd. Therefore, it’s specifications are subject to change or our products in it may be discontinued without advance notice. Please check with our

sales representatives or product engineers before ordering.

• This PDF catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.

!Note O30E.pdf

07.9.3

,ﬁw ﬂ

5

!Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.

• This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.

Microwave Coaxial Connectors

SMT FSC Type

■ Features

1. High engagement

2. Miniature (LxWxH: 3.4x3.4x1.5mm) for High

density mounting

3. Low profile (3.0mm max.)

4. SMD and reflow soldering applicable

5. Taping package applicable

6. Mountable by automatic placer

7. High performance (V.S.W.R. 1.3 max. at 3GHz)

8. Matched with ultra-thin FEP coaxial cables

(0.8mm dia)

■ Applications

Portable telephone, mobile telephone, cordless

telephone, GPS, and other microwave radio and

measurement equipment.

2.42.4ø2.2

3.8

Tolerances Unless

Otherwise Specified:±0.3

(in mm)

MXFG76_/MXFK81_

2.4

1

2.4

3.4

0.5

1.5

0.5

Hot Terminal

Ground Terminal

Tolerances Unless

Otherwise Specified:±0.2

(in mm)

MM7329-2700

3.4 3.2

0.2max

0.1max

0.5 2.4

1.5

2.4 0.4

0.5

2.9

: Hot Terminal

: Ground Terminal TOLERANCES UNLESS

OTHERWISE SPECIFIED : ±0.2

(in mm)

(1)

(2)

(3)

MM7329-2702

Part Number Rated

Voltage

(V)

Contact

Resistance (max.)

(ohm)

Withstanding

Voltage

(rms)

Insulation

Resistance (min.)

(M ohm)

Durability

(cycles)

Frequency

Rating

(GHz)

Temperature

Range

(degree C) VSWR Center Contact Outer Contact Insulator

MM7329-2700

250 0.015 300 (AC) 500 50 to 3.0 -40 to +90 1.3 max. Copper Alloy

Gold plated Copper Alloy

Gold plated Engineering plastic

MM7329-2702

250 0.015 300 (AC) 500 50 to 3.0 -40 to +90 1.3 max. Copper Alloy

Gold plated Copper Alloy

Gold plated Engineering plastic

Impedance: 50ohm

• This PDF catalog is downloaded from the website of Murata Manufacturing co., ltd. Therefore, it’s specifications are subject to change or our products in it may be discontinued without advance notice. Please check with our

sales representatives or product engineers before ordering.

• This PDF catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.

!Note O30E.pdf

07.9.3

5

!Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.

• This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.

for Receptacle

5.08 4.4

2.5

1.33

13.93

ø5.33

2.5

ø2.16

ø5.33

SMA-JACK

(in mm)

MM121454 (For FSC type receptacle)

for Cable Assembly

0.76

SMA-JACK

5.08 1.48

8.64

14.06

ø5.33

ø3.1

ø5.33

(in mm)

MM121460 (For FSC type cable assembly)

■ Land Pattern Dimensions

MM7329-2700B

· Pattern should be designed to match 50 ohm impedance circuit.

· Typical PCB material is glass epoxy (εr=4.8). Thickness is 1.0mm.

· The solder resist should be printed except for the land pattern on the PCB.

(Note)

5.2

4.2

3.4

2.4

2.52.57

1.7

2.2

3.4

0.9

1

(1.5) (1.74)

0.6 (1.5)

3-ø0.6

(Through hole)

ø1

Land

Electrode

(in mm)

MM7329-2702B

5.2

4.2

2.4

1

0.6

ø0.6

1.2

2.4

0.3

1.7

0.5

2.5

(1.74)

(1.5) (1.5)

Electrode

(in mm)

Land

· Pattern should be designed to match 50 ohm impedance circuit.

· Typical PCB material is glass epoxy (εr=4.8). Thickness is 1.0mm.

· The solder resist should be printed except for the land pattern on the PCB.

(Note)

■ Cable Length Tolerance

L

Cable Length L(mm)(∗)Dimensional

tolerance(mm)

Over Till

40

100

500

1000

100

500

1000

−

±3

±4

+2% of L

−0% of L

±10

∗L must be 40mm Min.

■ Profile Dimensions

Profile

Clearance for mating (in mm)

3max.

4.2 min.

Continued on the following page.

■ Measurement Adapter Dimensions

• This PDF catalog is downloaded from the website of Murata Manufacturing co., ltd. Therefore, it’s specifications are subject to change or our products in it may be discontinued without advance notice. Please check with our

sales representatives or product engineers before ordering.

• This PDF catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.

!Note O30E.pdf

07.9.3

5

!Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.

• This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.

Continued from the preceding page.

■ Disengagement Tool

5±0.6

20±2

5±1

0.5±0.62±0.6

3.5±0.6

ø2.7T1

45±2

(10)

(3)

(105) M19004

M19000 (for MM7329-2700) How to use tool (for MM7329-2700)

M19004 (for MM7329-2702) How to use tool (for MM7329-2702)

(in mm)

• This PDF catalog is downloaded from the website of Murata Manufacturing co., ltd. Therefore, it’s specifications are subject to change or our products in it may be discontinued without advance notice. Please check with our

sales representatives or product engineers before ordering.

• This PDF catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.

!Note O30E.pdf

07.9.3

Notice

5

!Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.

• This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.

■ Notice (Storage and Operating Condition)

1. Environment Conditions

(1) This product is designed for use in electrical

equipment in the environment (temperature,

humidity, atmospheric pressure, etc.)

specified in this approval drawing. It may not

be used in the following environments or under

the following conditions:

(a) Ambient air containing corrosive gas

(Chlorine gas, Hydrogen sulfide gas,

Ammonia gas, Sulfuric acid gas, Nitric

oxide gas, etc.)

(b) Ambient air containing volatile or

combustible gas

(c) In liquid (water, oil, chemical solution,

organic solvents, etc.)

(d) In environments with a high concentration of

airborne particles

(e) In direct sunlight

(f) Dusty conditions

(g) In freezing

(h) Other environments similar to the above

conditions

(2) Contact the manufacturer before using the

product in any of the above environments or

under any of the above conditions.

2. Storage

Store in manufacturer's package or tightly

re-closed box with the following conditions. Use

this product within 6 months after receipt. Check

the terminal solderability before use if the

product has been stored for more than 6 months.

Temperature: -10 to +40 degree C

Humidity: 15 to 85% RH

• This PDF catalog is downloaded from the website of Murata Manufacturing co., ltd. Therefore, it’s specifications are subject to change or our products in it may be discontinued without advance notice. Please check with our

sales representatives or product engineers before ordering.

• This PDF catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.

!Note O30E.pdf

07.9.3

Peak tern :5:

Notice

5

!Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.

• This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.

■ Notice (Soldering and Mounting)

1. Reflow soldering

Soldering must be carried out without exceeding the

allowable soldering temperature and time shown within

the shaded area of Figure "Allowable Temperature and

Time of Reflow Soldering".

In case the soldering is repeated, the maximum time in

Figure "Allowable Temperature and Time of Reflow

Soldering" should be accumulated time. The standard

soldering conditions are shown in Figure "Reflow

Soldering Standard Conditions".

Follow Standard pattern dimensions.

2. Soldering by soldering iron

Soldering by soldering iron should be carried out in

accordance to the following conditions.

Pre-heating Temperature 150D

Time 60 to 120 s.

Soldering Temperature (at the tip of the soldering

iron) less than 350D

Time less than 3 s.

3. We cannot warrant against mishaps caused by any use

of this product that deviates from allowable temperature

and time of reflow soldering.

4. In soldering, do not apply excessive mechanical force to

terminals or leads greater than specified in the drawing.

5. Please note the following in case of soldering terminals

or leads of the product.

(1) Use Rosin based flux, but not with strong acid flux

(Chlorine content should be less than 0.20wt%).

(2) Flux should be thoroughly cleaned from connector to

prevent possible deterioration of electrical

characteristics.

6. Please mount this product at the position so that stress

by wrap and/or bend of the PCB may not apply to it.

7. Please dry out this product immediately after soldering

and cleaning.

Allowable Temperature and Time of Reflow Soldering

Reflow Soldering Standard Conditions

260

250

240

230

220

210

200

190

180

240

230

150

100

25

0

Pre-heating 150±20D

Time (sec.)

30 sec. max.

30-50 sec.60-120 sec.

Peak temperature 250±5D

Temperature (D)

Solder: Sn-3.0Ag-0.5Cu

Measuring point of temperature: In-Out Terminals of the Device

Reflow Soldering: Both Convection and Infrared Rays

: Hot Air

: Hot Plate

30 60 90 120 150 180 210 240

Continued on the following page.

• This PDF catalog is downloaded from the website of Murata Manufacturing co., ltd. Therefore, it’s specifications are subject to change or our products in it may be discontinued without advance notice. Please check with our

sales representatives or product engineers before ordering.

• This PDF catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.

!Note O30E.pdf

07.9.3

72y” W

Notice

5

!Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.

• This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.

Continued from the preceding page.

■ Notice (Handling)

1. Usage Condition

(1) Do not apply electrical voltage greater than specified in

the drawing. It might cause degradation or destruction

of the product. Even if it endures during a short time,

long time qualification is not guaranteed.

(2) Confirm product's performance is not influenced by

contact of other components.

(3) Please contact the manufacturer beforehand, if the

product is to be used in frequently bent position.

2. Handling

(1) Avoid excessive stress when handling and transporting

printed circuit board after connector and/or assembly

has been secured to PCB.

(2) Do not try to pull the cable, when a connector with a

coaxial cable is handled.

(3) Disregarding the following notes could cause

mechanical damage and/or poor electrical performance.

3. Handling Instructions

(1) Cable is designed to fit only with MM7329-2700 and

MM7329-2702 receptacles. Any other receptacle can

not be used with this cable.

(2) Disengagement:

Use tool P/N M19000 (for MM7329-2700) or M19004

(for MM7329-2702) to insert or remove cable in a

vertical direction from receptacle. Avoid pulling only the

cable to prevent cable damage.

(3) Avoid twisting probe or cable when inserting or

removing from receptacle.

(4) Mechanical stress:

The stress to the connector should be limited as shown

in Figure 1.

(a) Stress to the housing.

Stress A and B: 4.9N max.

(b) Stress to the outer sleeve.

Stress C: 2.94N max.

Stress D: 1.96N max.

(c) Cable pull strength.

Stress E: 7.84N max. (for MM7329-2700)

4.9N max. (for MM7329-2702)

Figure 1. Mechanical Stress after Engagement

ABE

DC

B

E

DC

(MM7329-2700)

(MM7329-2702)

A

• This PDF catalog is downloaded from the website of Murata Manufacturing co., ltd. Therefore, it’s specifications are subject to change or our products in it may be discontinued without advance notice. Please check with our

sales representatives or product engineers before ordering.

• This PDF catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.

!Note O30E.pdf

07.9.3

Package

5

!Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.

• This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.

■ Dimensions of Reel

MM7329-2700RA1/RB4

Murata Part Number

MM7329-2700RA1

MM7329-2700RB4

TOLERANCE

A

178

330

±2.0

B

13

±0.5

C

21

±0.8

D

2

±0.5

N (min.)

Dia. 50

–

W1

13.5

±1.5

W2 (max.)

18.5

–

DBW1

W2

C

A

N

(in mm)

MM7329-2702RAB/RB2

Murata Part Number

MM7329-2702RAB

MM7329-2702RB2

TOLERANCE

A

178

330

±2.0

B

13

±0.5

C

21

±0.8

D

2

±0.5

N (min.)

Dia. 50

–

W1

13.5

±1.5

W2 (max.)

18.5

–

DBW1

W2

C

A

N

(in mm)

■ Dimensions of Taping

P2 P0 D

(in mm)

T

P1 A

W

FE

B

K

A

3.9±0.1 B

3.7±0.1 W

12±0.2 D

ø1.5 E

1.75±0.1 F

5.5±0.1 K

3±0.15 P0

4±0.1

+0.1

−0

P1

8±0.1 P2

2±0.1 T

0.3±0.05

■ Minimum Quantity

MM7329-2700RA1: dia.180 mm reel/1000 pcs.

MM7329-2700RB4: dia.330 mm reel/4000 pcs.

MM7329-2700B: Bulk/free

MM7329-2702RAB: dia.180 mm reel/ 500 pcs.

MM7329-2702RB2: dia.330 mm reel/2000 pcs.

MM7329-2702B: Bulk/free

• This PDF catalog is downloaded from the website of Murata Manufacturing co., ltd. Therefore, it’s specifications are subject to change or our products in it may be discontinued without advance notice. Please check with our

sales representatives or product engineers before ordering.

• This PDF catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.

!Note O30E.pdf

07.9.3

Miniaturized Microwave Coaxial Connector Cable List

Material

No. and Dia.

Total Dia.

Material

Melting point

(Reference only)

Total Dia.

Material

Dia. of wire

Total Dia.

Material

Nominal

thickness

Color

dB/m at 1GHz

dB/m at 2GHz

dB/m at 3GHz

dB/m at 4GHz

dB/m at 6GHz

Murata cable code

Assembly to FSC

Assembly to GSC

Assembly to HSC

-

(No./mm)

(mm)

-

Degree C

(mm)

-

(mm)

-

(mm)

-

(mm)

(Ohm)

(pF/m)

Inner

conductor

Insulator

Outer

conductor

Sheath

Overall Dia.

Minimum bending radius

Nominal impedance

Continuous operating voltage

Nominal static capacitance

Nominal

Insertion

loss

0.8D single shield

FEP cable

76

Silver coated copper

covered steel wire

1/0.26

0.26

FEP

285

0.8

Tin plated copper wire

0.05

1.05

FEP

0.1

Gray

1.24

6

50

300 Vrms max.

100

1.56

2.3

2.9

3.5

Suitable

Not Suitable

0.4D single shield

FEP cable

81

Silver coated

copper wire

7/0.05

0.15

FEP

250

0.4

Tin plated copper wire

0.05

0.65

FEP

0.05

White

0.8

4.8

50

300 Vrms max.

100

3.0

4.26

5.24

6.18

Suitable

Not Suitable

0.4D single shield

PFA cable

88

Silver coated copper

covered steel wire

1/0.15

0.15

PFA

302-310

0.43

Tin plated copper wire

0.05

0.68

PFA

0.075

White

0.83

3.3

50

300 Vrms max.

100

2.89

4.28

5.39

6.44

8.4

Not Suitable

Suitable

Not Suitable

0.4D single shield

PFA cable

92

Silver coated

copper wire

7/0.05

0.15

PFA

302-310

0.4

Tin plated copper wire

0.05

0.65

PFA

0.075

White

0.8

3.3

50

300 Vrms max.

100

3.0

4.26

5.24

6.18

9.17

Not Suitable

Suitable

Not Suitable

0.4D single shield

PFA cable

32

Silver coated

copper wire

7/0.05

0.15

PFA

302-310

0.4

Silver plated copper wire

0.05

0.65

PFA

0.075

White

0.8

3.3

50

300 Vrms max.

100

3.0

4.26

5.24

6.18

9.17

Not Suitable

Suitable

!Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.

• This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.

• This PDF catalog is downloaded from the website of Murata Manufacturing co., ltd. Therefore, it’s specifications are subject to change or our products in it may be discontinued without advance notice. Please check with our

sales representatives or product engineers before ordering.

• This PDF catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.

!Note O30E.pdf

07.9.3

Murala Manufacturing Co., Ltd.

Note:

1. Export Control

<

For customers outside Japan

>

No muRata products should be used or sold, through any channels, for use in the design, development, production, utilization, maintenance or operation of, or

otherwise contribution to (1) any weapons (Weapons of Mass Destruction (nuclear, chemical or biological weapons or missiles) or conventional weapons) or (2)

goods or systems specially designed or intended for military end-use or utilization by military end-users.

<

For customers in Japan

>

For products which are controlled items subject to the “Foreign Exchange and Foreign Trade Law” of Japan, the export license specified by the law is required

for export.

2. Please contact our sales representatives or product engineers before using the products in this catalog for the applications listed below, which require especially

high reliability for the prevention of defects which might directly damage a third party's life, body or property, or when one of our products is intended for use in

applications other than those specified in this catalog.

qAircraft equipment wAerospace equipment

eUndersea equipment rPower plant equipment

tMedical equipment yTransportation equipment (vehicles, trains, ships, etc.)

uTraffic signal equipment iDisaster prevention / crime prevention equipment

oData-processing equipment !0 Application of similar complexity and/or reliability requirements to the applications listed above

3. Product specifications in this catalog are as of July 2007. They are subject to change or our products in it may be discontinued without advance notice. Please

check with our sales representatives or product engineers before ordering. If there are any questions, please contact our sales representatives or product

engineers.

4. Please read rating and CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.

5. This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or

transact the approval sheet for product specifications before ordering.

6. Please note that unless otherwise specified, we shall assume no responsibility whatsoever for any conflict or dispute that may occur in connection with the effect

of our and/or a third party's intellectual property rights and other related rights in consideration of your use of our products and/or information described or

contained in our catalogs. In this connection, no representation shall be made to the effect that any third parties are authorized to use the rights mentioned

above under licenses without our consent.

7. No ozone depleting substances (ODS) under the Montreal Protocol are used in our manufacturing process.

International DivisionHead Office

http://www.murata.com/

• This PDF catalog is downloaded from the website of Murata Manufacturing co., ltd. Therefore, it’s specifications are subject to change or our products in it may be discontinued without advance notice. Please check with our

sales representatives or product engineers before ordering.

• This PDF catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.

!Note O30E.pdf

07.9.3

Microwave Coaxial Catalog Datasheet by Murata Electronics

INFORMATION

HELP

CONTACT US

FOLLOW US