Desco 的 Full Time Continuous Monitor 规格书

规格书反馈/错误

(5} FULL-“ME CONTINUOUS MONI'IOR WA...—VE 5 5 63110?! Ul'tumlull wmlmu DESCO nummn mag-Mm mmmn WAVE DISTORTION

Employee Owned

DESCO WEST - 3651 Walnut Avenue, Chino, CA 91710 • (909) 627-8178

DESCO EAST - One Colgate Way, Canton, MA 02021-1407 • (781) 821-8370 • Website: Desco.com

Full-Time Continuous Monitor

Installation, Operation and Maintenance

Description

The Desco Full-Time Continuous Monitor is a single

workstation continuous monitor. It continuously monitors

the wiring of an AC outlet, path-to-ground integrity

of one operator, and the ground plane of one ESD

worksurface. Mounting tabs make it suitable to install

in workbench or equipment settings. The embedded

relay terminal activates when a pass condition is

displayed the monitor and maybe connected to

machines for access control or other devices. Connect

the 19323 Power Relay accessory to control power to

workbenches, hand tools, and other electronic devices

dependent on the Full-Time Continuous Monitor's

status.

The Full-Time Continuous Monitor is designed

with Wave Distortion Technology to provide stable

continuous monitoring of the path-to-ground and

presence of 1 megohm resistance of an operator’s wrist

strap. Audio and visual alarms activate (in less than

500 milliseconds) when the operator unintentionally

disconnects from the monitor or the wrist strap

connection points are intermittent. The Full-Time

Continuous Monitor also monitors for a worksurface

path-to-ground of less than 10 megohms and the

integrity of the electrical ground used to by the monitor

All Full-Time Continuous Monitors are calibrated to NIST

standards and include a certificate.

March 2021

Wave Distortion Technology is the Most Reliable

Technology for the Continuous Monitoring of

Single-Wire (Conductor) Wrist Straps

“Wave Distortion” or vector impedance works by

applying a continuous test voltage of 1.2 volts

peak-to-peak at 1 to 2 microamperes (0.000002

amperes) to the wrist strap that is connected to the

continuous or constant monitor. The test voltage creates

a square wave that the monitor circuit compares to

established patterns. By monitoring the “distortions”, or

shape of the square wave, Wave Distortion Technology

determines if the monitored circuit is complete - the

operator is in the circuit and the total equivalent DC

resistance is within specifications. Wave Distortion

Technology produces a very fast alarm time and

minimal false alarms.

ANSI/ESD S20.20 section 7.3 states “Compliance

verification records shall be established and maintained

to provide evidence of conformity to the technical

requirements.” Per ANSI/ESD S1.1 Annex A.3 Daily

(wrist strap system) testing may be omitted if constant

monitoring used.” Per ESD Handbook ESD TR 20.20

section 5.3.2.4.4 “Typical Test programs recommend

that wrist straps that are used daily should be tested

daily. However, if the products that are being produced

are of such value that knowledge of a continuous,

reliable ground is needed, and then continuous

monitoring should be considered or even required.”

The Full-Time Continuous Monitor and its accessories

are available as the following item numbers:

Item Description

19321 Full-Time Continuous Monitor, with North

America Power Cord

19322 Full-Time Continuous Monitor, with UK Power

Cord

19323 Power Relay, North America

19327 Power Cord, North America

19328 Power Cord, UK

98221 Wave Distortion Monitor Verification Tester

Made in the

United States of America

TECHNICAL BULLETIN TB-3086

Figure 1. Desco Full-Time Continuous Monitor

15-3056

Employee Owned

DESCO WEST - 3651 Walnut Avenue, Chino, CA 91710 • (909) 627-8178

DESCO EAST - One Colgate Way, Canton, MA 02021-1407 • (781) 821-8370 • Website: Desco.com

Packaging

19321 Full-Time Continuous Monitor

1 Full-Time Continuous Monitor

1 Mat Monitor Cord (White)

1 Countersunk Washer

1 Flat Head Screw, 6-32 x 1/4"

2 Pan-Head Screws, #6 x 3/8"

1 Dual Lock Fastener Set, 2" Length

1 Power Cord with North American Plug

1 Certificate of Calibration

19322 Full-Time Continuous Monitor

1 Full-Time Continuous Monitor

1 Mat Monitor Cord (White)

1 Countersunk Washer

1 Flat Head Screw, 6-32 x 1/4"

2 Pan-Head Screws, #6 x 3/8"

1 Dual Lock Fastener Set, 2" Length

1 10mm Interchangeable Park Snap

1 10mm Operator Jack Adapter

1 Power Cord with UK Plug

1 Certificate of Calibration

19323 Remote Alarm

1 Power Relay

1 Interface Cable

1 Power Cord with North American Plug

Figure 3. Desco 19321 Full-Time Continuous Monitor

packaging contents

Figure 4. Desco 19322 Full-Time Continuous Monitor

packaging contents

Figure 5. Desco 19323 Power Relay packaging contents

FULL-TIME CONTINUOUS MommR WWW TIE-3056

Employee Owned

DESCO WEST - 3651 Walnut Avenue, Chino, CA 91710 • (909) 627-8178

DESCO EAST - One Colgate Way, Canton, MA 02021-1407 • (781) 821-8370 • Website: Desco.com

Features and Components

Full-Time Continuous Monitor

Figure 6. Full-Time Continuous Monitor features and

components

A. Park Snap: Allows the operator to disconnect (and

park) a wrist strap when leaving the workstation, without

creating a false alarm. Touch the park snap or park

switch, and the monitor's audible alarm will disable for

approximately 8 seconds. Use this time to disconnect

the wrist cord from the wristband, and attach it to the

park snap or remove the banana plug from the jack.

Upon returning to the workstation and disconnecting

the wrist cord from the park snap, the operator has

approximately 8 seconds to reconnect the wrist cord to

a worn wristband before activating the alarm.

B. Monitored Operator Jack: Insert the single-wire

wrist cord here to monitor the operator's connection to

ground.

C. Operator LEDs: Illuminates green when the

operator is properly grounded. Illuminates solid red and

audible alarm sounds when the operator is not properly

grounded.

D. Mat LEDs: Illuminates green when the worksurface

is properly grounded. Illuminates red and audible alarm

sounds when the worksurface is not properly grounded.

E. Ground LEDs: Illuminates green when the AC outlet

is properly wired and its path to equipment ground via

the equipment ground conductor is intact. Illuminates

red and audible alarm sounds when the AC outlet is not

properly wired and its path to equipment ground via the

equipment ground conductor is broken.

F. Park Switch: Allows the operator to disconnect (and

park) a wrist strap when leaving the workstation, without

creating a false alarm. Touch the park snap or park

switch, and the monitor's audible alarm will disable for

approximately 8 seconds. Use this time to disconnect

the wrist cord from the wristband, and attach it to the

park snap or remove the banana plug from the jack.

Upon returning to the workstation and disconnecting

the wrist cord from the park snap, the operator has

approximately 8 seconds to reconnect the wrist cord

to a worn wristband before activating the alarm. The 8

second timer is indicated by the growing intensity of the

park switch's blue LED. The blue LED will pulse when

the operator jack is vacant to indicate standby mode.

G. Power Inlet: Connect the included power cord here.

H. Mat Monitor Screw Terminal: Verifies that the

worksurface's path-to-ground is less than 10 megohms.

Connect the white mat monitor cord here.

I. Set Switch: Toggles the monitor's settings for the

audible alarm and mat monitor circuit.

Function Procedure

Audible Alarm

Volume

1. Push and release the switch to

toggle the buzzer's volume.

2. The volume will toggle from low,

medium, and high settings.

Enable / Disable

Mat Monitor

Circuit

1. Push and hold the switch until

all LEDs illmuniate orange.

2. Release the switch.

3. An illuminated MAT LED

indicates that the mat

monitor circuit is enabled. A

non-illuminated MAT LED

indicates that the mat monitor

circuit is disabled.

J. Relay Terminal: Integrates with electronic locks,

lights, buzzers, etc. See the "Relay Terminal" section for

more information.

K. Accessory Jack: Connects to the 19323 Power

Relay accessory.

vows»: RELAY DEECD TIE-3056

Employee Owned

DESCO WEST - 3651 Walnut Avenue, Chino, CA 91710 • (909) 627-8178

DESCO EAST - One Colgate Way, Canton, MA 02021-1407 • (781) 821-8370 • Website: Desco.com

Installation

Power Relay

Figure 7. Power Relay features and components

A. Normally On Receptacle: Provides power unless

the operator is connected to the Full-Time Continuous

Monitor, and it reports all PASS conditions.

B. Always On Receptacle: Always provides power

regardless of the Full-Time Continuous Monitor's status.

C. Switch Active LED: Illuminates green when the

internal relay switch is activated.

D. Interface Connector: Use the included interface

cable to connect the Full-Time Continuous Monitor to

this connector.

E. Normally Off Receptacles: Provides power when

the operator is connected to the Full-Time Continuous

Monitor, and it does not report any alarm conditions.

F. Power Switch: Rock to RESET to turn on the Power

Relay. Rock to OFF to turn off the Power Relay.

G. Power LED: Illuminates red when the Power Relay

is powered.

H. Power Inlet: Connect the included power cord here.

Figure 8. Installing the Full-Time Continuous Monitor

Mat Monitor Cord

Full-Time

Continuous Monitor

Grounded

Worksurface Mat

Power Cord

Countersunk Washer

Flat Head Screw

1. Remove the Full-Time Continuous Monitor from the

carton, and inspect for damage.

2. Determine the mounting location of the Full-Time

Continuous Monitor. Its LEDs should be visible

to the operator. Secure the Full-Time Continuous

Monitor to a surface using its mounting tabs and the

included pan head screws or dual lock fasteners.

3. Secure the ring termination of the white mat monitor

cord to the mat monitor screw terminal on the back

of the Full-Time Continuous Monitor.

4. Connect the mat monitor cord from the back of

the Full-Time Continuous Monitor to a grounded

worksurface mat. Use the included countersunk

washer and flat head screw to secure the cord to

the grounded mat.

5. Connect the power cord to the power inlet located

on the back of the Full-Time Continuous Monitor.

Connect the opposite end to an appropriate AC

outlet.

TB-3DE6

Employee Owned

DESCO WEST - 3651 Walnut Avenue, Chino, CA 91710 • (909) 627-8178

DESCO EAST - One Colgate Way, Canton, MA 02021-1407 • (781) 821-8370 • Website: Desco.com

Pair the 19321 Full-Time Continuous Monitor with the

Power Relay to control power to workbenches, hand

tools, and other electronic devices dependent on the

monitor's status.

1. Determine the mounting location of the Power

Relay. Locate it within reach of its included power

cord. The Power Relay's mounting tabs may be to

secure it onto a surface.

2. Connect the included power cord to the power inlet

located on the side of the Power Relay. Connect the

opposite end to an appropriate AC outlet.

NOTE: The Power Relay is only rated to accept

90-120 VAC input voltage.

3. Connect the included interface cable to the back

of the Full-Time Continuous Monitor. Connect the

opposite end to the green connector on the side of

the Power Relay.

4. Connect the power cord from the Full-Time Monitor

to the Always ON receptacle on the Power Relay.

5. Connect the power cord of the external electronic

device to one of the Normally OFF receptacles on

the Power Relay.

6. Toggle the power switch to the RESET position.

Both the Full-Time Continuous Monitor and the

Power Relay will power on.

7. This setup will power the external electronic device

whenever an operator connects to the Full-Time

Continuous Monitor and no alarms are reported.

Power Relay

Figure 9. Desco 19323 Power Relay Figure 10. Installing the Power Relay

External

Electronic Device

Full-Time

Continuous Monitor

Interface

Cable

Figure 11. Using the Power Relay

15-3056

Employee Owned

DESCO WEST - 3651 Walnut Avenue, Chino, CA 91710 • (909) 627-8178

DESCO EAST - One Colgate Way, Canton, MA 02021-1407 • (781) 821-8370 • Website: Desco.com

Relay Terminal

The Full-Time Continuous Monitor features a relay

terminal that can be integrated with electronic locks,

lights, buzzers, etc. The relay will activate when a failure

is reported by the Full-Time Continuous Monitor.

Contact Form 2 Form C

Maximum Switching Power 60 W, 125 VAC

Maximum Switching Voltage 220 VDC, 250 VAC

Maximum Switching Current 2 A

Maximum Carrying Current 2 A

NC NOC

Figure 12. Relay terminal contacts

10 mm Snap Adapters

The 19322 Full-Time Continuous Monitor includes an

interchangeable 10 mm park snap and 10 mm banana

jack adapter for operators who use wrist cords with

10 mm terminations. Use the park snap's knurled rim

to unscrew the 4 mm park snap from the monitor and

install the 10 mm park snap to the monitor. Plug the 10

mm operator jack adapter into the monitor's operator

jack.

Figure 13. Installing the 10 mm snap adapters to the

19322 Full-Time Continuous Monitor

Operation

1. Fit the wristband snugly onto the wrist.

2. Snap the wrist cord to the wristband.

3. Plug the wrist cord into the operator jack. The green

operator LED will illuminate. This indicates that the

operator is properly grounded.

4. If this does not happen, examine the wrist cord for

continuity or damage and the wristband to ensure

that it fits securely. If you have dry skin, apply an

approved dissipative hand lotion such as Menda

Reztore® ESD Hand Lotion.

5. When leaving the workstation, first touch the

monitor's park switch or park snap. The monitor's

audible alarm will disable for approximately 8

seconds. Use this time to disconnect the wrist cord

from the wristband and attach it to the park snap

without sounding a false alarm.

6. Upon returning to the workstation and disconnecting

the wrist cord from the park snap, the monitor will

provide approximately 8 seconds for the operator to

reconnect the wrist cord to a worn wristband before

sounding the monitor's alarm.

Figure 14. Using the Full-Time Continuous Monitor when

mounted underneath a workbench tabletop

aaaaaa

Employee Owned

DESCO WEST - 3651 Walnut Avenue, Chino, CA 91710 • (909) 627-8178

DESCO EAST - One Colgate Way, Canton, MA 02021-1407 • (781) 821-8370 • Website: Desco.com

Figure 15. Using the Full-Time Continuous Monitor when

mounted on a workbench upright

Figure 16. Using the Full-Time Continuous Monitor at a

machine station

Calibration

Frequency of recalibration should be based on the

critical nature of those ESD sensitive items handled

and the risk of failure for the ESD protective equipment

and materials. In general, Desco recommends that

calibration be performed annually.

Use the Desco 98221 Wave Distortion Monitor

Verification Tester to perform periodic verification

(once every 6-12 months) of the Full-Time Continuous

Monitor. The verification tester can be used to check the

test limits of the Full-Time Continuous Monitor without

removing it from the workstation.

See TB-3074 for more information.

Figure 17. Desco 98221 Wave Distortion Monitor

Verification Tester

TIE-3036

Employee Owned

DESCO WEST - 3651 Walnut Avenue, Chino, CA 91710 • (909) 627-8178

DESCO EAST - One Colgate Way, Canton, MA 02021-1407 • (781) 821-8370 • Website: Desco.com

Specifications

Full-Time Continuous Monitor

Input Voltage and

Frequency

Power Input:

100-240 VAC, 50/60 Hz

Power Cord Length:

6 ft. (1.8 m)

Operating Temperature 50 to 95° F (10 to 35° C)

Environmental

Requirements

Indoor use only at altitudes

less than 6500 ft. (2 km)

Maximum relative humidity

of 80% up to 85° F (30° C)

decreasing linearly to 50% @

85° F (30° C)

Dimensions 2.85" L x 5.13" W x 1.00" H

(72 mm x 130 mm x 25 mm)

Weight 0.35 lbs. (0.16 kg)

Operator Test Range*500 kilohms to 10 megohms

impedance

Worksurface Test

Limit**

10 megohms (±20%)

Operator Test Voltage 1.2 V peak-to-peak @ 1.2 µA,

open circuit

Worksurface Test

Voltage

5 to 7.5 V, open circuit

Alarm Response Time <500 ms

Country of Origin United States of America

*This cannot be verified with standard DC test

equipment. The continuous monitor is an impedance

sensing device, and the limits are determined by the

magnitude and angle of the impedance.

**The worksurface mat must have a conductive

layer such as Dual Layer Rubber or Dissipative

3-Layer Vinyl with conductive buried layers. Desco

workstation monitors are not recommended for use with

homogeneous matting.

ANSI/ESD S20.20 requires the use of a surface

resistance meter for periodic verification of a

worksurface's resistance-to-ground (Rtg). Constant

monitors may not be used as a substitute for this

requirement.

Power Relay

Input Voltage and

Frequency

90-120 VAC, 50/60 Hz

Output Voltage 90-140 VAC

Max Load 12 A

Input Connector C-13/C-14

Output Connector 4x NEMA 5-15

Outlet Types 2x Normally OFF

1x Normally ON

1x Always ON

Dimensions 6.7" L x 3.7" W x 1.4" H

(170 mm x 95 mm x 35 mm)

Weight 0.7 lbs. (0.32 kg)

Power Cord Length 1.5 ft. (0.5 m)

Interface Cable Length 7 ft. (2.1 m)

Operating Temperature -35 to 145° F (-37 to 63° C)

Environmental

Requirements

5 to 95% RH non-condensing

Indoor use only

Country of Origin China

Figure 18. Mounting hole locations on the Full-Time

Continuous Monitor (all dimensions are in inches)

Limited Warranty, Warranty Exclusions, Limit

of Liability and RMA Request Instructions

See the Desco Warranty -

Desco.com/Limited-Warranty.aspx

Desco 的 Full Time Continuous Monitor 规格书

信息

帮助

联系我们

关注我们