STMicroelectronics 的 STMPE811 规格书

规格书反馈/错误

.lJﬂJ

April 2011 Doc ID 14489 Rev 5 1/66

STMPE811

S-Touch® advanced resistive touchscreen controller

with 8-bit GPIO expander

Features

■8 GPIOs

■1.8 - 3.3 V operating voltage

■Integrated 4-wire touchscreen controller

■Interrupt output pin

■Wakeup feature on each I/O

■SPI and I2C interface

■Up to 2 devices sharing the same bus in

I2C mode (1 address line)

■8-input 12-bit ADC

■128-depth buffer touchscreen controller

■Touchscreen movement detection algorithm

■25 kV air-gap ESD protection (system level)

■4 kV HBM ESD protection (device level)

Applications

■Portable media players

■Game consoles

■Mobile and smartphones

■GPS

Description

The STMPE811 is a GPIO (general purpose

input/output) port expander able to interface a

main digital ASIC via the two-line bidirectional bus

(I2C). A separate GPIO expander is often used in

mobile multimedia platforms to solve the

problems of the limited amount of GPIOs typically

available on the digital engine.

The STMPE811 offers great flexibility, as each I/O

can be configured as input, output or specific

functions. The device has been designed with

very low quiescent current and includes a wakeup

feature for each I/O, to optimize the power

consumption of the device.

A 4-wire touchscreen controller is built into the

STMPE811. The touchscreen controller is

enhanced with a movement tracking algorithm (to

avoid excessive data), a 128 x 32 bit buffer and

programmable active window feature.

QFN16

(3x3)

Table 1. Device summary

Order code Package Packaging

STMPE811QTR QFN16 Tape and reel

www.st.com

Contents STMPE811

2/66 Doc ID 14489 Rev 5

Contents

1 STMPE811 functional overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

2 Pin configuration and functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

2.1 Pin functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

3 I2C and SPI interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

3.1 Interface selection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

4 I2C interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

4.1 I2C features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

4.2 Data input . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

4.3 Read operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

4.4 Write operations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

5 SPI interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

5.1 SPI protocol definition . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

5.1.1 Register reading . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

5.1.2 Register write . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

5.1.3 Termination of data transfer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

5.2 SPI timing modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

5.2.1 SPI timing definition . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

6 STMPE811 registers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

7 System and identification registers . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22

8 Interrupt system . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25

9 Analog-to-digital converter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29

10 Touchscreen controller . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33

10.1 Driver and switch control unit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33

11 Touchscreen controller programming sequence . . . . . . . . . . . . . . . . . 46

STMPE811 Contents

Doc ID 14489 Rev 5 3/66

12 Temperature sensor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48

13 GPIO controller . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50

13.0.1 Power supply . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52

13.0.2 Power-up reset (POR) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53

14 Maximum rating . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54

14.1 Recommended operating conditions . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55

15 Electrical specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56

16 Package mechanical data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58

17 Revision history . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 64

List of tables STMPE811

4/66 Doc ID 14489 Rev 5

List of tables

Table 1. Device summary . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1

Table 2. Pin assignments . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

Table 3. Pin configuration for IN2, IN3 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

Table 4. Pin configuration for X+, Y+, X-, Y-. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

Table 5. Interface selection pins . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

Table 6. I2C address . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

Table 7. I2C timing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

Table 8. Operating modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

Table 9. SPI timing modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

Table 10. SPI timing specification. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

Table 11. Register summary map table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

Table 12. System and identification registers map . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22

Table 13. ADC controller register summary table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29

Table 14. ADC conversion time . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32

Table 15. Touchscreen controller register summary table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35

Table 16. Touchscreen controller DATA register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43

Table 17. Touchscreen parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48

Table 18. GPIO control registers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50

Table 19. Absolute maximum ratings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54

Table 20. Power consumption . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55

Table 21. DC electrical characteristics (-40 °C to 85 °C) all GPIOs comply to JEDEC standard JESD-

8-7) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56

Table 22. AC electrical characteristics (-40 °C to 85 °C) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56

Table 23. ADC specification (-40 °C to 85 °C) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57

Table 24. Switch drivers specification. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57

Table 25. Voltage reference specification. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57

Table 26. Package mechanical data for QFN16 (3 x 3 x 1 mm) - 0.50 pitch . . . . . . . . . . . . . . . . . . . 60

Table 27. Exposed pad variation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60

Table 28. Footprint dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61

Table 29. Document revision history . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 64

STMPE811 List of figures

Doc ID 14489 Rev 5 5/66

List of figures

Figure 1. STMPE811 functional block diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

Figure 2. STMPE811 pin configuration (top through view) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

Figure 3. STMPE811 interface. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

Figure 4. STMPE811 I2C interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

Figure 5. I2C timing diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

Figure 6. Read and write modes (random and sequential) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

Figure 7. SPI timing specification. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18

Figure 8. Interrupt system diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25

Figure 9. Touchscreen controller block diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33

Figure 10. Window tracking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34

Figure 11. Sampling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34

Figure 12. Package outline for QFN16 (3 x 3 x 1 mm) - 0.50 pitch . . . . . . . . . . . . . . . . . . . . . . . . . . . 59

Figure 13. Recommended footprint . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61

Figure 14. Carrier tape for QFN16 (3 x 3 x 1 mm) - 0.50 pitch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 62

Figure 15. Reel information for QFN16 (3 x 3 x 1 mm) - 0.50 pitch . . . . . . . . . . . . . . . . . . . . . . . . . . . 63

6/66 \NT AO'Data am SCLK/CLK Therma‘ SDAT/CS 59"“ \ GND vcc Doc ‘0 14489 Rev 5 ‘7]

STMPE811 functional overview STMPE811

6/66 Doc ID 14489 Rev 5

1 STMPE811 functional overview

The STMP811 consists of the following blocks:

●I2C and SPI interface

●Analog-to-digital converver (ADC)

●Touchscreen controller (TSC)

●Driver and switch control unit

●Temperature sensor

●GPIO controller

Figure 1. STMPE811 functional block diagram

Switches

and drivers

GND

SCLK/CLK

SDAT/CS

A0/Data out

VCC

INT

ADC , TSC

VREF

Thermal

sense

RC oscillator

Data in

TSC: Touchscreen controller

GPIO

controller

I C / SPI

interface

GPIO 0-7

/ADC IN 0-7

/MODE

/REF-, REF+

Table 2. Pin assignments Pin Name Funclion 1 V— Y-/GP|O-7 2 INT Inlerrupl oulpul (Vcc domain)‘ open drain 3 AO/Data Oul IZC address in Resell Dala oul in SPI mode (Vcc domain) 4 SCLK IZC/SPI clock (Vcc domain) 5 SDAT I20 dala/SPI 03 (V00 domain) 6 Vcc 1.8 73.3 V supply vollage 7 Dale in SPI Dala In (V00 domain) 8 INO IND/GPlO-O IN1/GPlO-1/MODE 9 |N1 In RESET state, MODE selecls lhe lype ol serial inlerface “o“ - r20 “1 “ - SF'l 10 GND Ground 11 INZ IN2/GPlO-2 12 INS INB/GPlO-B 13 X+ X+/GPIO-4 14 Vro Supply for louchscreen driver and GPIO 15 V+ Y+/GPIO-5 16 X- X-/GP|O-6 Doc ID 14489 Rev 5 7/66

STMPE811 Pin configuration and functions

Doc ID 14489 Rev 5 7/66

2 Pin configuration and functions

Figure 2. STMPE811 pin configuration (top through view)

Table 2. Pin assignments

Pin Name Function

1 Y- Y-/GPIO-7

2 INT Interrupt output (VCC domain), open drain

3 A0/Data Out I2C address in Reset, Data out in SPI mode (VCC domain)

4SCLKI

2C/SPI clock (VCC domain)

5SDATI

2C data/SPI CS (VCC domain)

CC 1.8 −3.3 V supply voltage

7 Data in SPI Data In (VCC domain)

8 IN0 IN0/GPIO-0

9IN1

IN1/GPIO-1/MODE

In RESET state, MODE selects the type of serial interface

"0" - I2C

"1" - SPI

10 GND Ground

11 IN2 IN2/GPIO-2

12 IN3 IN3/GPIO-3

13 X+ X+/GPIO-4

14 Vio Supply for touchscreen driver and GPIO

15 Y+ Y+/GPIO-5

16 X- X-/GPIO-6

1 2 3 4

12 11 10 9

STMPE811

Pin configuration and functions STMPE811

8/66 Doc ID 14489 Rev 5

2.1 Pin functions

The STMPE811 is designed to provide maximum features and flexibility in a very small pin-

count package. Most of the pins are multi-functional. Ta b l e 3 and Ta bl e 4 show how to select

the pin’s function.

Table 3. Pin configuration for IN2, IN3

Pin / control

GPIO_AF = 1 GPIO_AF = 0

ADC control 1 bit 1 =

don’t care ADC control 1 bit 1 = 0 ADC control 1 bit 1 = 1

IN0 GPIO-0 ADC

IN1 GPIO-1 ADC

IN2 GPIO-2 ADC External reference +

IN3 GPIO-3 ADC External reference -

Table 4. Pin configuration for X+, Y+, X-, Y-

Pin / control

GPIO_AF = 1 GPIO_AF = 0

TSC control 1 bit 0 =

don’t care TSC control 1 bit 0 = 0 TSC control 1 bit 0 = 1

X+ GPIO-4 ADC TSC X+

Y+ GPIO-5 ADC TSC Y+

X- GPIO-6 ADC TSC X-

Y- GPIO-7 ADC TSC Y-

Table 5. Interface selection pins Pin IZC lunclion 3 Address 0 4 CLOCK 5 SDATA 7 7 9 MODE Doc ID 14489 Rev 5

STMPE811 I2C and SPI interface

Doc ID 14489 Rev 5 9/66

3 I2C and SPI interface

3.1 Interface selection

The STMPE811 interfaces with the host CPU via a I2C or SPI interface. The pin IN_1 allows

the selection of interface protocol at reset state.

Figure 3. STMPE811 interface

Table 5. Interface selection pins

Pin I2C function SPI function Reset state

3 Address 0 Data out CPHA for SPI

4CLOCKCLOCK−

5 SDATA CS CPOL_N for SPI

7−Data in −

9MODEI

2C set to ‘0’ Set to ‘1’ for SPI

SPI I/F

module

I C I/F

module

DIN

DOUT

CLK

SDAT

SCLK

MUX

unit

10/66 GND VCC SC SDAT ADDRO SC SDAT Table 6. IZC address ADDRO 0 1 For the bus master to communicate 10 the slave device, the b condition and be iollowed by ihe slave device address. Acco address, is a read/write bit (Fi/W). The bit is set to 1 for read maich occurs on ihe siave device address, the corresponding on the SDA during the 9m bitiime. I1 there is no maich, it des responding io ihe transaction. Figure 5. IZC timing diagram _/ / V Doc ID 14489 Rev 5

I2C interface STMPE811

10/66 Doc ID 14489 Rev 5

4 I2C interface

The addressing scheme of STMPE811 is designed to allow up to 2 devices to be connected

to the same I2C bus.

Figure 4. STMPE811 I2C interface

For the bus master to communicate to the slave device, the bus master must initiate a Start

condition and be followed by the slave device address. Accompanying the slave device

address, is a read/write bit (R/W). The bit is set to 1 for read and 0 for write operation. If a

match occurs on the slave device address, the corresponding device gives an acknowledge

on the SDA during the 9th bit time. If there is no match, it deselects itself from the bus by not

responding to the transaction.

Figure 5. I2C timing diagram

Table 6. I2C address

ADDR0 Address

00x82

10x88

ADDR0

SDAT

GND

VCC

STMPE811

AI00589

SDA

tSU:STOtSU:STA

tHD:STA

SCL

tSU:DAT

tHD:DAT

tHIGH

tLOW

tHD:STAtBUF

STMPE811 I2C interface

Doc ID 14489 Rev 5 11/66

Table 7. I2C timing

Symbol Parameter Min Typ Max Uni

fSCL SCL clock frequency 0 −400 kHz

tLOW Clock low period 1.3 −−

µs

tHIGH Clock high period 600 −−

tFSDA and SCL fall time −300 ns

tHD:STA

START condition hold time (after this

period the first clock is generated) 600 −−

tSU:STA

START condition setup time (only relevant

for a repeated start period) 600 −−

tSU:DAT Data setup time 100 −−

tHD:DAT Data hold time 0 −−

µs

tSU:STO STOP condition setup time 600 −−

tBUF

Time the bus must be free before a new

transmission can start 1.3 −−

µs

I2C interface STMPE811

12/66 Doc ID 14489 Rev 5

4.1 I2C features

The features that are supported by the I2C interface are listed below:

●I2C slave device

●Operates at 1.8 V

●Compliant to Philips I2C specification version 2.1

●Supports standard (up to 100 Kbps) and fast (up to 400 Kbps) modes

Start condition

A Start condition is identified by a falling edge of SDATA while SCLK is stable at high state.

A Start condition must precede any data/command transfer. The device continuously

monitors for a Start condition and does not respond to any transaction unless one is

encountered.

Stop condition

A Stop condition is identified by a rising edge of SDATA while SCLK is stable at high state. A

Stop condition terminates communication between the slave device and the bus master. A

read command that is followed by NoAck can be followed by a Stop condition to force the

slave device into idle mode. When the slave device is in idle mode, it is ready to receive the

next I2C transaction. A Stop condition at the end of a write command stops the write

operation to registers.

Acknowledge bit

The acknowledge bit is used to indicate a successful byte transfer. The bus transmitter

releases the SDATA after sending eight bits of data. During the ninth bit, the receiver pulls

the SDATA low to acknowledge the receipt of the eight bits of data. The receiver may leave

the SDATA in high state if it does not acknowledge the receipt of the data.

STMPE811 I2C interface

Doc ID 14489 Rev 5 13/66

4.2 Data input

The device samples the data input on SDATA on the rising edge of the SCLK. The SDATA

signal must be stable during the rising edge of SCLK and the SDATA signal must change

only when SCLK is driven low.

Figure 6. Read and write modes (random and sequential)

Table 8. Operating modes

Mode Byte Programming sequence

Read ≥1

Start, Device address, R/W = 0, Register address to be read

Restart, Device address, R/W = 1, Data Read, Stop

If no Stop is issued, the Data Read can be continuously performed. If

the register address falls within the range that allows an address auto-

increment, then the register address auto-increments internally after

every byte of data being read.

Write ≥1

Start, Device address, R/W = 0, Register address to be written, Data

Write, Stop

If no Stop is issued, the Data Write can be continuously performed. If

the register address falls within the range that allows address auto-

increment, then the register address auto-increments internally after

every byte of data being written in. For those register addresses that

fall within a non-incremental address range, the address is kept static

throughout the entire write operation. Refer to the memory map table

for the address ranges that are auto and non-increment.

Start

R/W=0

Ack

Device

Address

Reg

Address

Ack

Device

Address

Ack

R/W=1

Data

Read

No Ack

Stop

One byte

Read

Start

R/W=0

Ack

Device

Address

Reg

Address

Ack

Restart

Device

Address

Ack

R/W=1

Data

Read

Ack

More than one byte

Read

Ack

No Ack

Stop

Data

Read + 1

Data

Read + 2

Start

R/W=0

Ack

Device

Address

Reg

Address

Ack

Data

to be

written

Ack

Stop

One byte

Write

More than one byte

Read

Start

R/W=0

Ack

Device

Address

Reg

Address

Ack

Data to

Write

Ack

Stop

Data to

Write + 2

Ack

Data to

Write + 1

Master

Slave

AM00775V1

I2C interface STMPE811

14/66 Doc ID 14489 Rev 5

4.3 Read operation

A write is first performed to load the register address into the Address Counter but without

sending a Stop condition. Then, the bus master sends a reStart condition and repeats the

Device Address with the R/W bit set to 1. The slave device acknowledges and outputs the

content of the addressed byte. If no additional data is to be read, the bus master must not

acknowledge the byte and terminates the transfer with a Stop condition.

If the bus master acknowledges the data byte, then it can continue to perform the data

reading. To terminate the stream of data bytes, the bus master must not acknowledge the

last output byte, and be followed by a Stop condition. If the address of the register written

into the Address Counter falls within the range of addresses that has the auto-increment

function, the data being read are coming from consecutive addresses, which the internal

Address Counter automatically increments after each byte output. After the last memory

address, the Address Counter 'rolls-over' and the device continues to output data from the

memory address of 0x00. Similarly, for the register address that falls within a non-increment

range of addresses, the output data byte comes from the same address (which is the

address referred by the Address Counter).

Acknowledgement in read operation

For the above read command, the slave device waits, after each byte read, for an

acknowledgement during the ninth bit time. If the bus master does not drive the SDA to a

low state, then the slave device terminates and switches back to its idle mode, waiting for

the next command.

4.4 Write operations

A write is first performed to load the register address into the Address Counter without

sending a Stop condition. After the bus master receives an acknowledgement from the slave

device, it may start to send a data byte to the register (referred by the Address Counter).

The slave device again acknowledges and the bus master terminates the transfer with a

Stop condition.

If the bus master needs to write more data, it can continue the write operation without

issuing the Stop condition. Whether the Address Counter autoincrements or not after each

data byte write depends on the address of the register written into the Address Counter.

After the bus master writes the last data byte and the slave device acknowledges the receipt

of the last data, the bus master may terminate the write operation by sending a Stop

condition. When the Address Counter reaches the last memory address, it 'rolls-over' to the

next data byte write.

STMPE811 SPI interface

Doc ID 14489 Rev 5 15/66

5 SPI interface

The SPI (serial peripheral interface) in STMPE811 uses a 4-wire communication connection

(DATA IN, DATA OUT, CLK, CS). In the diagram, “Data in” is referred to as MOSI (master

out slave in) and “DATA out” is referred to as MISO (master in slave out).

5.1 SPI protocol definition

The SPI follows a byte-sized transfer protocol. All transfers begin with an assertion of CS_n

signal (falling edge). The protocol for reading and writing is different and the selection

between a read and a write cycle is dependent on the first captured bit on the slave device.

A '1' denotes a read operation and a '0' denotes a write operation. The SPI protocol defined

in this section is shown in Figure 3.

The following are the main features supported by this SPI implementation.

●Support of 1 MHz maximum clock frequency.

●Support for autoincrement of address for both read and write.

●Full duplex support for read operation.

●Daisy chain configuration support for write operation.

●Robust implementation that can filter glitches of up to 50 ns on the CS_n and SCL pins.

●Support for all 4 modes of SPI as defined by the CPHA, CPOL bits on SPICON.

5.1.1 Register reading

The following steps need to be followed for the register read through the SPI.

1. Assert CS_n by driving a '0' on this pin.

2. Drive a '1' on the first SCL launch clock on MOSI to select a read operation.

3. The next 7 bits on MOSI denote the 7-bit register address (MSB first).

4. The next address byte can now be transmitted on the MOSI. If the autoincrement bit is

set, the following address transmitted on the MOSI is ignored. Internally, the address is

incremented. If the autoincrement bit is not set, then the following byte denotes the

address of the register to be read next.

5. Read data is transmitted by the slave device on the MISO (MSB first), starting from the

launch clock following the last address bit on the MOSI.

6. Full duplex read operation is achieved by transmitting the next address on MOSI while

the data from the previous address is available on MISO.

7. To end the read operation, a dummy address of all 0's is sent on MOSI.

SPI interface STMPE811

16/66 Doc ID 14489 Rev 5

5.1.2 Register write

The following steps need to be followed for register write through SPI.

1. Assert CS_n by driving a '0' on this pin.

2. Drive a '0' on the first SCL launch clock on MOSI to select a write operation.

3. The next 7 bits on MOSI denote the 7-bit register address (MSB first).

4. The next byte on the MOSI denotes data to be written.

5. The following transmissions on MOSI are considered byte-sized data. The register

address to which the following data is written depends on whether the autoincrement

bit in the SPICON register is set. If this bit has been set previously, the register address

is incremented for data writes.

5.1.3 Termination of data transfer

A transfer can be terminated before the last launch edge by deasserting the CS_n signal. If

the last launch clock is detected, it is assumed that the data transfer is successful.

STMPE811 SPI interface

Doc ID 14489 Rev 5 17/66

5.2 SPI timing modes

The SPI timing modes are defined by CPHA and CPOL,CPHA and CPOL are read from the

"SDAT" and "A0" pins during power-up reset. The following four modes are defined

according to this setting.

The clocking diagrams of these modes are shown in ON reset. The device always operates

in mode 0. Once the bits are set in the SPICON register, the mode change takes effect on

the next transaction defined by the CS_n pin being deasserted and asserted.

5.2.1 SPI timing definition

Table 9. SPI timing modes

CPOL_N (SDAT pin) CPOL CPHA (ADDR pin) Mode

1000

1011

0102

0113

Table 10. SPI timing specification

Symbol Description

Timing

Unit

Min Typ Max

tCSS

CS_n falling to

first capture

clock

1−−

µs

tCL

Clock low

period 500 −−

tCH

Clock high

period 500 −−

tLDI

Launch clock

to MOSI data

valid

−−

20 ns

tLDO

Launch clock

to MISO data

valid

−−

330 µs

tDI

Data on MOSI

valid 1−−

µs

tCCS

Last clock

edge to CS_n

high

1−−

µs

tCSH

CS_n high

period 2−−

µs

L 3J1 scL \(OSI \uso “g spermm.

SPI interface STMPE811

18/66 Doc ID 14489 Rev 5

Figure 7. SPI timing specification

tCSCL

CS_n high to

first clock edge 300 −−

tCSZ

CS_n high to

tri-state on

MISO

1−−

µs

Table 10. SPI timing specification (continued)

Symbol Description

Timing

Unit

Min Typ Max

STMPE811 STMPE811 registers

Doc ID 14489 Rev 5 19/66

6 STMPE811 registers

This section lists and describes the registers of the STMPE811 device, starting with a

Table 11. Register summary map table

Address Register name Bit Type Reset value Function

0x00 CHIP_ID 16 R 0x0811 Device identification

0x02 ID_VER 8 R 0x03

Revision number

0x01 for engineering sample

0x03 for final silicon

0x03 SYS_CTRL1 8 R/W 0x00 Reset control

0x04 SYS_CTRL2 8 R/W 0x0F Clock control

0x08 SPI_CFG 8 R/W 0x01 SPI interface configuration

0x09 INT_CTRL 8 R/W 0x00 Interrupt control register

0x0A INT_EN 8 R/W 0x00 Interrupt enable register

0x0B INT_STA 8 R 0x10 interrupt status register

0x0C GPIO_EN 8 R/W 0x00 GPIO interrupt enable

0x0D GPIO_INT_STA 8 R 0x00 GPIO interrupt status

0x0E ADC_INT_EN 8 R/W 0x00 ADC interrupt enable

0x0F ADC_INT_STA 8 R 0x00 ADC interrupt status register

0x10 GPIO_SET_PIN 8 R/W 0x00 GPIO set pin register

0x11 GPIO_CLR_PIN 8 R/W 0x00 GPIO clear pin register

0x12 GPIO_MP_STA 8 R/W 0x00 GPIO monitor pin state

0x13 GPIO_DIR 8 R/W 0x00 GPIO direction register

0x14 GPIO_ED 8 R/W 0x00 GPIO edge detect register

0x15 GPIO_RE 8 R/W 0x00 GPIO rising edge register

0x16 GPIO_FE 8 R/W 0x00 GPIO falling edge register

0x17 GPIO_AF 8 R/W 0x00 Alternate function register

0x20 ADC_CTRL1 8 R/W 0x1C ADC control

0x21 ADC_CTRL2 8 R/W 0x01 ADC control

0x22 ADC_CAPT 8 R/W 0xFF To initiate ADC data

acquisition

0x30 ADC_DATA_CH0 16 R 0x0000 ADC channel 0

0x32 ADC_DATA_CH1 16 R 0x0000 ADC channel 1

STMPE811 registers STMPE811

20/66 Doc ID 14489 Rev 5

0x34 ADC_DATA_CH2 16 R 0x0000 ADC channel 2

0x36 ADC_DATA_CH3 16 R 0x0000 ADC channel 3

0x38 ADC_DATA_CH4 16 R 0x0000 ADC channel 4

0x3A ADC_DATA_CH5 16 R 0x0000 ADC channel 5

0x3C ADC_DATA_CH6 16 R 0x0000 ADC channel 6

0x3E ADC_DATA_CH7 16 R 0x0000 ADC channel 7

0x40 TSC_CTRL 8 R/W 0x90 4-wire touchscreen

controller setup

0x41 TSC_CFG 8 R/W 0x00 Touchscreen controller

configuration

0x42 WDW_TR_X 16 R/W 0x0FFF Window setup for top right X

0x44 WDW_TR_Y 16 R/W 0x0FFF Window setup for top right Y

0x46 WDW_BL_X 16 R/W 0x0000 Window setup for bottom left

0x48 WDW_BL_Y 16 R/W 0x0000 Window setup for bottom left

0x4A FIFO_TH 8 R/W 0x00 FIFO level to generate

interrupt

0x4B FIFO_STA 8 R/W 0x20 Current status of FIFO

0x4C FIFO_SIZE 8 R 0x00 Current filled level of FIFO

0x4D TSC_DATA_X 16 R 0x0000 Data port for touchscreen

controller data access

0x4F TSC_DATA_Y 16 R 0x0000 Data port for touchscreen

controller data access

0x51 TSC_DATA_Z 8 R 0x0000 Data port for touchscreen

controller data access

0x52 TSC_DATA_XYZ 32 R 0x00000000 Data port for touchscreen

controller data access

0x56 TSC_FRACTION

_Z 8 0x00 Touchscreen controller

FRACTION_Z

0x57 TSC_DATA 8 R 0x00 Data port for touchscreen

controller data access

0x58 TSC_I_DRIVE 8 R/W 0x00 Touchscreen controller drive

0x59 TSC_SHIELD 8 R/W 0x00 Touchscreen controller

shield

0x60 TEMP_CTRL 8 R/W 0x00 Temperature sensor setup

Table 11. Register summary map table (continued)

Address Register name Bit Type Reset value Function

STMPE811 STMPE811 registers

Doc ID 14489 Rev 5 21/66

0x61 TEMP_DATA 8 R 0x00 Temperature data access

port

0x62 TEMP_TH 8 R/W 0x00 Threshold for temperature

controlled interrupt

Table 11. Register summary map table (continued)

Address Register name Bit Type Reset value Function

System and identification registers STMPE811

22/66 Doc ID 14489 Rev 5

7 System and identification registers

CHIP_ID Device identification

Address: 0x00

Type: R

Reset: 0x0811

Description: 16-bit device identification

ID_VER Revision number

Address: 0x02

Type: R

Reset: 0x03 (0x01 for engineering samples)

Description: 16-bit revision number

Table 12. System and identification registers map

Address Register name Bit Type Reset Function

0x00 CHIP_ID 16 R 0x0811 Device identification

0x02 ID_VER 8 R 0x03 Revision number

(0x03 for engineering sample)

0x03 SYS_CTRL1 8 R/W 0x00 Reset control

0x04 SYS_CTRL2 8 R/W 0x0F Clock control

0x08 SPI_CFG 8 R/W 0x01 SPI interface configuration

STMPE811 System and identification registers

Doc ID 14489 Rev 5 23/66

SYS_CTRL1 Reset control

Address: 0x03

Type: R/W

Reset: 0x00

Description: The reset control register enables to reset the device

SYS_CTRL2 Clock control

Address: 0x04

Type: R/W

Reset: 0x0F

Description: This register enables to switch off the clock supply

76543 2 1 0

RESERVED SOFT_RESET HIBERNATE

[7:2] RESERVED

[1] SOFT_RESET: Reset the STMPE811 using the serial communication interface

[0] HIBERNATE: Force the device into hibernation mode.

Forcing the device into hibernation mode by writing ‘1’ to this bit would disable the hot-key

feature. If the hot-key feature is required, use the default auto-hibernation mode.

76543 2 1 0

−−−−

TS_OFF GPIO_OFF TSC_OFF ADC_OFF

[7:4] RESERVED

[3] TS_OFF: Switch off the clock supply to the temperature sensor

1: Switches off the clock supply to the temperature sensor

[2] GPIO_OFF: Switch off the clock supply to the GPIO

1: Switches off the clock supply to the GPIO

[1] TSC_OFF: Switch off the clock supplyto the touchscreen controller

1: Switches off the clock supply to the touchscreen controller

[0] ADC_OFF: Switch off the clock supply to the ADC

1: Switches off the clock supply to the ADC

System and identification registers STMPE811

24/66 Doc ID 14489 Rev 5

SPI_CFG SPI interface configuration

Address: 0x08

Type: R/W

Reset: 0x01

Description: SPI interface configuration register

76543 2 1 0

RESERVED AUTO_INCR SPI_CLK_MOD1 SPI_CLK_MOD0

[7:3] RESERVED

[2] AUTO_INCR:

This bit defines whether the SPI transaction follows an addressing scheme that internally

autoincrements or not

[1] SPI_CLK_MOD1:

This bit reflects the value of the SCAD/A0 pin during power-up reset

[0] SPI_CLK_MOD0:

This bit reflects the value of the SCAD/A0 pin during power-up reset

STMPE811 8 Interrupt system The STMPE811 uses a Ziner imerrupt sIrucrure. The are ganged as a sing‘e bit m me “\nrerrupi sxaius regx muchscreen comroller and remperarure sensor can b register. Figure 8. Interrupt system diagram GPIO mrenupr srams ‘7] Doc ID 14489 Rev 5

STMPE811 Interrupt system

Doc ID 14489 Rev 5 25/66

8 Interrupt system

The STMPE811 uses a 2-tier interrupt structure. The ADC interrupts and GPIO interrupts

are ganged as a single bit in the “interrupt status register”. The interrupts from the

touchscreen controller and temperature sensor can be seen directly in the interrupt status

Figure 8. Interrupt system diagram

GPIO

interrupt

status

FIFO status,

TSC touch,

Temp sensor

AND

Interrupt

enable

Interrupt

status

AND

GPIO

interrupt

enable

AND

ADC

interrupt

enable

ADC

interrupt

status

Interrupt system STMPE811

26/66 Doc ID 14489 Rev 5

INT_CTRL Interrupt control register

Address: 0x09

Type: R/W

Reset: 0x00

Description: The interrupt control register is used to enable the interruption from a system-related

interrupt source to the host.

76543 2 1 0

RESERVED INT_POLARITY INT_TYPE GLOBAL_INT

[7:3] RESERVED

[2] INT_POLARITY: This bit sets the INT pin polarity

1: Active high/rising edge

0: Active low/falling edge

[1] INT_TYPE: This bit sets the type of interrupt signal required by the host

1: Edge interrupt

0: Level interrupt

[0] GLOBAL_INT: This is master enable for the interrupt system

1: Global interrupt

0: Stops all interrupts

STMPE811 Interrupt system

Doc ID 14489 Rev 5 27/66

INT_EN Interrupt enable register

Address: 0x0A

Type: R/W

Reset: 0x00

Description: The interrupt enable register is used to enable the interruption from a system related

interrupt source to the host.

INT_STA Interrupt status register

Address: 0x0B

Type: R

Reset: 0x10

Description: The interrupt status register monitors the status of the interruption from a particular

interrupt source to the host. Regardless of whether the INT_EN bits are enabled, the

INT_STA bits are still updated. Writing '1' to this register clears the corresponding

bits. Writing '0' has no effect.

76543 2 1 0

GPIO ADC TEMP_SENS FIFO_EMPTY FIFO_FULL FIFO_0FLOW FIFO_TH TOUCH_DET

[7] GPIO: Any enabled GPIO interrupts

[6] ADC: Any enabled ADC interrupts

[5] TEMP_SENS: Temperature threshold triggering

[4] FIFO_EMPTY: FIFO is empty

[3] FIFO_FULL: FIFO is full

[2] FIFO_OFLOW: FIFO is overflowed

[1] FIFO_TH: FIFO is equal or above threshold value.

[0] TOUCH_DET: Touch is detected

76543 2 1 0

GPIO ADC TEMP_SENS FIFO_EMPTY FIFO_FULL FIFO_OFLOW FIFO_TH TOUCH_DET

[7] GPIO: Any enabled GPIO interrupts

[6] ADC: Any enabled ADC interrupts

[5] TEMP_SENS: Temperature threshold triggering

[4] FIFO_EMPTY: FIFO is empty

[3] FIFO_FULL: FIFO is full

[2] FIFO_OFLOW: FIFO is overflowed

[1] FIFO_TH: FIFO is equal or above threshold value.

This bit is set when FIFO level equals to threshold value. It will only be asserted again if FIFO

level drops to < threshold value, and increased back to threshold value.

[0] TOUCH_DET: Touch is detected

Interrupt system STMPE811

28/66 Doc ID 14489 Rev 5

GPIO_INT_EN GPIO interrupt enable register

Address: 0x0C

Type: R/W

Reset: 0x00

Description: The GPIO interrupt register enables the GPIO interruption of a particular GPIO

source to the host.

GPIO_INT_STA GPIO interrupt status register

Address: 0x0D

Type: R

Reset: 0x00

Description: The GPIO interrupt status register monitors the status of the interruption from a

particular GPIO pin interrupt source to the host. Regardless of whether or not the

GPIO_INT_STA bits are enabled, the corresponding GPIO_STA bits are still updated.

The ISG[7:0] bits are the interrupt status bits corresponding to the GPIO[7:0] pins.

Writing '1' to this register clears the corresponding bits. Writing '0' has no effect.

76543 2 1 0

IEG[x]

[7:0] IEG[x]: Interrupt enable GPIO mask (where x = 7 to 0)

1: Writing ‘1’ to the IE[x] bit enables the interruption to the host

76543 2 1 0

ISG[x]

[7:0] ISG[x]: GPIO interrupt status (where x = 7 to 0)

Read:

Interrupt status of the GPIO[x]. Reading the register clears any bits that have been set to '1'

Write:

Writing to this register has no effect

STMPE811 Interrupt system

Doc ID 14489 Rev 5 29/66

ADC_INT_EN ADC interrupt enable register

Address: 0x0E

Type: R/W

Reset: 0x00

Description: The ADC enable register enables the interruption of a particular ADC source to the

host.

ADC_INT_STA ADC interrupt status register

Address: 0x0F

Type: R

Reset: 0x00

Description: The ADC interrupt status register monitors the status of the interruption from a

particular ADC source to the host. Regardless of whether or not the ADC_INT_EN

bits are enabled, the corresponding ADC_STA bits are still updated. The ISA[7:0] bits

are the interrupt status bits corresponding to the ADC[7:0] pins. Writing '1' to this

76543 2 1 0

IEAC[x]

[7:0] IEAC[x]: Interrupt enable ADC mask (where x = 7 to 0)

1: Writing ‘1’ to the IE[x] bit enables the interruption to the host

76543 2 1 0

ISA[x]

[7:0] ISA[x]: ADC interrupt status (where x = 7 to 0)

Read:

Interrupt status of the ADC[x]. Reading the register clears any bits that have been set to '1'

Write:

Writing to this register has no effect.

Note: Refer to Ta b l e 1 3 for the associated ADC intput pins to each ADC channels.

Analog-to-digital converter STMPE811

30/66 Doc ID 14489 Rev 5

9 Analog-to-digital converter

An 8-input,12-bit analog-to-digital converter (ADC) is integrated in the STMPE811. The ADC

can be used as a generic analog-to-digital converter, or as a touchscreen controller capable

of controlling a 4-wire resistive touchscreen.

Table 13. ADC controller register summary table

Address Register name Size Description

0x20 ADC_CTRL1 8 ADC control

0x21 ADC_CTRL2 8 ADC control

0x22 ADC_CAPT 8 ADC channel data capture

0x30 ADC_DATA_CH0 8 ADC channel 0 (X+/GPIO-4)

0x32 ADC_DATA_CH1 8 ADC channel 1 (X-/GPIO-6)

0x34 ADC_DATA_CH2 8 ADC channel 2 (Y+/GPIO-5)

0x36 ADC_DATA_CH3 8 ADC channel 3 (Y-/GPIO-7)

0x38 ADC_DATA_CH4 8 ADC channel 4 (IN0/GPIO0)

0x3A ADC_DATA_CH5 8 ADC channel 5 (IN1/GPIO-1)

0x3C ADC_DATA_CH6 8 ADC channel 6 (IN2/GPIO-2)

0x3E ADC_DATA_CH7 8 ADC channel 7 (IN3/GPIO-3)

STMPE811 Analog-to-digital converter

Doc ID 14489 Rev 5 31/66

ADC_CTRL1 ADC control 1

Address: 0x20

Type: R/W

Reset: 0x1C

Description: ADC control register.

76543210

RESERVED SAMPLE_TIME2 SAMPLE_TIME1 SAMPLE_TIME0 MOD_12B RESERVED REF_SEL RESERVED

[7] RESERVED

[6:4] SAMPLE_TIMEn: ADC conversion time in number of clock

000: 36

001: 44

010: 56

011: 64

100: 80

101: 96

110: 124

111: Not valid

[3] MOD_12B: Selects 10 or 12-bit ADC operation

1: 12 bit ADC

0: 10 bit ADC

[2] RESERVED

[1] REF_SEL: Selects between internal or external reference for the ADC

1: External reference

0: Internal reference

[0] RESERVED

Analog-to-digital converter STMPE811

32/66 Doc ID 14489 Rev 5

ADC_CTRL2 ADC control 2

Address: 0x21

Type: R/W

Reset: 0x01

Description: ADC control.

ADC_CAPT ADC channel data capture

Address: 0x22

Type: R/W

Reset: 0xFF

Description: To initiate ADC data acquisition.

76543 2 1 0

RESERVED ADC_FREQ_1 ADC_FREQ_0

[7] RESERVED

[6] RESERVED

[5] RESERVED

[4] RESERVED

[3] RESERVED

[2] RESERVED

[1:0] ADC_FREQ: Selects the clock speed of ADC

00: 1.625 MHz typ.

01: 3.25 MHz typ.

10: 6.5 MHz typ.

11: 6.5 MHz typ.

76543 2 1 0

CH[7:0]

[7:0] CH[7:0]: ADC channel data capture

Write '1' to initiate data acquisition for the corresponding channel. Writing '0' has no effect.

Reads '1' if conversion is completed. Reads '0' if conversion is in progress.

STMPE811 Analog-to-digital converter

Doc ID 14489 Rev 5 33/66

ADC_DATA_CHn ADC channel data registers

Address: Add address

Type: R/W

Reset: 0x0000

Description: ADC data register 0-7 (DATA_CHn=0 -7)

The ADC in STMPE811 operates on an internal RC clock with a typical frequency of

6.5 MHz. The total conversion time in ADC mode depends on the "SampleTime" setting,

and the clock division field 'Freq'.

The following table shows the conversion time based on 6.5 MHz, 3.25 MHz and 1.625 MHz

clock.

11109876543 2 1 0

DATA[11:0]

[11:0] DATA[11:0]: ADC channel data

If TSC is enabled, CH3-0 is used for TSC and all readings to these channels give 0x0000

Table 14. ADC conversion time

Sample time

setting

Conversion time

in ADC clock

6.5 MHz

(154 ns)

3.25 MHz

(308 ns)

1.625 MHz

(615 ns)

000 36 5.5 µs (180 kHz) 11 µs (90 kHz) 22 µs (45 kHz)

001 44 6.8 µs (147 kHz) 13.6 µs (74 kHz) 27 µs (36 kHz)

010 56 8.6 µs (116 kHz) 17.2 µs (58 kHz) 34.4 µs (29 kHz)

011 64 9.9 µs (101 kHz) 19.8 µs (51 kHz) 39.6 µs (25 kHz)

100 80 12.3 µs(81.5 kHz) 24.6 µs (41 kHz) 49.2 µs (20 kHz)

101 96 14.8 µs (67.6 kHz) 28.8 µs (33 kHz) 59.2 µs (17 kHz)

110 124 19.1 µs (52.3 kHz) 38.2 µs (26 kHz) 56.4 µs (13 kHz)

10.1 34/66 Driver and switch control unit The driver and sztch control unit allows coordination of the ADC and the M the coordination of this unit, a stream of data is produced at a selected freq The touchscreen drivers can be configured with 2 current ratings: 20 mA 0 case where multiple touchdown on the screen is causing a short, the curren is limited to these values. Tolerance of these current setting is +/. 25%. Movement tracking The “Tracking Index" in the TSC_CTFlL register specilies a value, which de distance between the current touch position and the previous touch positlo is shoner than the tracking index, it is discarded. The tracking lS calculated by summation of the horizontal and vertical move is only reported it: (Current X . PreVlously Reported X) + (Current Y . Previously Reported Y) If pressure reporting is enabled (X/Y/Z), an increase in pressure override th tracking and report the new data set, even if X/Y is within the previous track to ensure that a slow touch is not discarded. If pressure data is not used, select X/Y mode in touchscreen data acduisitio in TSCControI register). Doc ID 14489 Rev 5

Touchscreen controller STMPE811

34/66 Doc ID 14489 Rev 5

10 Touchscreen controller

The STMPE811 is integrated with a hard-wired touchscreen controller for 4-wire resistive

type touchscreen. The touchscreen controller is able to operate completely autonomously,

and interrupt the connected CPU only when a pre-defined event occurs.

Figure 9. Touchscreen controller block diagram

10.1 Driver and switch control unit

The driver and switch control unit allows coordination of the ADC and the MUX/switch. With

the coordination of this unit, a stream of data is produced at a selected frequency.

The touchscreen drivers can be configured with 2 current ratings: 20 mA or 50 mA. In the

case where multiple touch-down on the screen is causing a short, the current from the driver

is limited to these values. Tolerance of these current setting is +/- 25%.

Movement tracking

The "Tracking Index" in the TSC_CTRL register specifies a value, which determines the

distance between the current touch position and the previous touch position. If the distance

is shorter than the tracking index, it is discarded.

The tracking is calculated by summation of the horizontal and vertical movement. Movement

is only reported if:

(Current X - Previously Reported X) + (Current Y - Previously Reported Y) > Tracking Index

If pressure reporting is enabled (X/Y/Z), an increase in pressure override the movement

tracking and report the new data set, even if X/Y is within the previous tracking index. This is

to ensure that a slow touch is not discarded.

If pressure data is not used, select X/Y mode in touchscreen data acquisition. (Opmode field

in TSCControl register).

Movement

window tracking

10/12 bit

ADC

Switch

drivers

Driver

switch control

FIFO

interrupt control

FIFO

STMPE811 Touchscreen controller

Doc ID 14489 Rev 5 35/66

Window tracking

The -WDW_X and WDW_Y registers allow to pre-set a sub-window in the touchscreen such

that any touch position that is outside the sub-window is discarded.

Figure 10. Window tracking

FIFO

FIFO has a depth of 128 sectors. This is enough for 128 sets of touch data at maximum

resolution (2 x 12 bits). FIFO can be programmed to generate an interrupt when it is filled to

a pre-determined level.

Sampling

The STMPE811 touchscreen controller has an internal 180 kHz, 12-bit ADC able to execute

autonomous driving/sampling. Each "sample" consists of 4 ADC readings that provide the X

and Y locations, as well as the touch pressure.

Figure 11. Sampling

Active window

Top right coordinates

Bottom left coordinates

ADC

takes X reading

Settling

period

Drive X

ADC

takes Y reading

Settling

period

Drive Y

Touchscreen controller STMPE811

36/66 Doc ID 14489 Rev 5

Oversampling and averaging function

The STMPE811 touchscreen controller can be configured to oversample by 2/4/8 times and

provide the averaged value as final output. This feature helps to reduce the effect of

surrounding noise.

Table 15. Touchscreen controller register summary table

Address Register name Bit Type Function

0x40 TSC_CTRL 8 R/W 4-wire touchscreen controller setup

0x41 TSC_CFG 8 R/W TSC configuration register

0x42 WDW_TR_X 16 R/W Window setup for top right X

0x44 WDW_TR_Y 16 R/W Window setup for top right Y

0x46 WDW_TR_X 16 R/W Window setup for bottom left X

0x48 WDW_TR_Y 16 R/W Window setup for bottom left Y

0x4A FIFO_TH 8 R/W FIFO level to generate interrupt

0x4B FIFO_STA 8 R/W Current status of FIFO

0x4C FIFO_SIZE 8 R Current filled level of FIFO

0x4D TSC_DATA_X 16 R Data port for TSC data access

0x4F TSC_DATA_Y 16 R Data port for TSC data access

0x51 TSC_DATA_Z 8 R Data port for TSC data access

0x52 TSC_DATA_XYZ 32 R Data port for TSC data access

0x56 TSC_FRACT_Z 8 R/W Touchscreen controller FRACTION_Z

0x57 TSC_DATA 8 R Touchscreen controller data access port

0x58 TSC_I_DRIVE 8 R/W Touchscreen controller drive I

0x59 TSC_SHIELD 8 R/W Touchscreen controller shield

STMPE811 Touchscreen controller

Doc ID 14489 Rev 5 37/66

TSC_CTRL touchscreen controller control register

Address: 0x40

Type: R/W

Reset: 0x90

Description: 4-wire touchscreen controller (TSC) setup.

76543 2 1 0

TSC_STA TRACK OP_MOD EN

[7] TSC_STA: TSC status

Reads '1' when touch is detected

Reads '0' when touch is not detected

Writing to this register has no effect

[6:4] TRACK: Tracking index

000: No window tracking

001: 4

010: 8

011: 16

100: 32

101: 64

110: 92

111: 127

[3:1] OP_MOD: TSC operating mode

000: X, Y, Z acquisition

001: X, Y only

010: X only

011: Y only

100: Z only

This field cannot be written on, when EN = 1

[0] EN: Enable TSC

Touchscreen controller STMPE811

38/66 Doc ID 14489 Rev 5

TSC_CFG Touchscreen controller configuration register

Address: 0x41

Type: R/W

Description: Touchscreen controller configuration register.

76543 2 1 0

AVE_CTRL_1 AVE_CTRL_0 TOUCH_DET

_DELAY_2

TOUCH_DET

_DELAY_1

TOUCH_DET

_DELAY_0 SETTLING_2 SETTLING_1 SETTLING_0

[7:6] [AVE_CTRL_1/0: Average control

00=1 sample

01=2 samples

10=4 samples

11=8 samples

[5:3] TOUCH_DET_DELAY_2/1/0: Touch detect delay

000 - 10 μs

001 - 50 μs

010 = 100 μs

011 = 500 μs

100=1ms

101=5ms

110 = 10 ms

111 = 50 ms

[2:0] SETTLING: Panel driver settling time(1)

000 = 10 μs

001 = 100 μs

010 = 500 μS

011=1ms

100=5ms

101 = 10 ms

110 = 50 ms

111=100ms

1. For large panels (> 6”), a capacitor of 10 nF is recommended at the touchscreen terminals for noise filtering.

In this case, settling time of 1 ms or more is recommended.

STMPE811 Touchscreen controller

Doc ID 14489 Rev 5 39/66

WDW_TR_X Window setup for top right X

Address: 0x42

Type: R/W

Reset: 0x0FFF

Description: Window setup for top right X coordinates.

WDW_TR_Y Window setup for top right Y

Address: 0x44

Type: R/W

Reset: 0x0FFF

Description: Window setup for top right Y coordinates.

7 6543 2 1 0

TR_X [11:0]

[11:0] TR_X: Bit 11:0 of top right X coordinates

7 6543 2 1 0

TR_Y [11:0]

[11:0] TR_X: Bit 11:0 of top right Y coordinates

Touchscreen controller STMPE811

40/66 Doc ID 14489 Rev 5

WDW_BL_X Window setup for bottom left X

Address: 0x46

Type: R/W

Reset: 0x0000

Description: Window setup for bottom left X coordinates.

WDW_BL_Y Window setup for bottom left Y

Address: 0x48

Type: R/W

Reset: 0x0000

Description: Window setup for bottom left Y coordinates.

FIFO_TH FIFO threshold

Address: 0x4A

Type: R/W

Reset: 0x00

Description: Triggers an interrupt upon reaching or exceeding the threshold value. This field must not be set

as zero.

7 6543 2 1 0

BL_X [11:0]

[11:0] BL_X: Bit 11:0 of bottom left X coordinates

7 6543 2 1 0

BL_Y [11:0]

[11:0] BL_X: Bit 11:0 of bottom left Y coordinates

76543 2 1 0

FIFO_TH

[7:0] FIFO_TH: touchscreen controller FIFO threshold

STMPE811 Touchscreen controller

Doc ID 14489 Rev 5 41/66

FIFO_STA FIFO status

Address: 0x4B

Type: R/W

Reset: 0x20

Description: Current status of FIFO..

FIFO_SIZE FIFO size

Address: 0x4C

Type: R

Reset: 0x00

Description: Current number of samples available.

765432 1 0

FIFO_OFLOW FIFO_FULL FIFO_EMPTY FIFO_TH_TRIG RESERVED FIFO_RESET

[7] FIFO_OFLOW:

Reads 1 if FIFO is overflow

[6] FIFO_FULL:

Reads 1 if FIFO is full

[5] FIFO_EMPTY:

Reads 1 if FIFO is empty

[4] FIFO_TH_TRIG:

0 = Current FIFO size is still below the threshold value

1 = Current FIFO size is at or beyond the threshold value

[3:1] RESERVED

[0] FIFO_RESET:

Write '0' : FIFO put out of reset mode

Write '1' : Resets FIFO. All data in FIFO are cleared.

When TSC is enabled, FIFO resets automatically.

76543 2 1 0

RESERVED FIFO_SIZE

[7:0] FIFO_SIZE: Number of samples available

Touchscreen controller STMPE811

42/66 Doc ID 14489 Rev 5

TSC_DATA_X TSC_DATA_X

Address: 0x4D

Type: R

Reset: 0x0000

Description: Bit 11:0 of X data.

11109876543 2 1 0

DATAY[11:0]

[11:0] DATAY[11:0]: Bit 11:0 of X data

STMPE811 Touchscreen controller

Doc ID 14489 Rev 5 43/66

TSC_DATA_Y TSC_DATA_Y

Address: 0x4F

Type: R

Reset: 0x0000

Description: Bit 11:0 of Y data.

TSC_DATA_Z TSC_DATA_Z

Address: 0x51

Type: R

Reset: 0x0000

Description: Bit 7:0 of Z data.

11109876543 2 1 0

DATAY[11:0]

[11:0] DATAY[11:0]: bit 11:0 of Y data

76543 2 1 0

DATAZ[7:0]

[7:0] DATAZ[7:0]: bit 7:0 of Z data

Touchscreen controller STMPE811

44/66 Doc ID 14489 Rev 5

TSC_DATA_XYZ Touchscreen controller DATA

Address: 0x57 (auto-increment), 0xD7 (non-auto-increment)

Type: R

Reset: 0x00

Description: Data port for TSC data access

The data format from the TSC_DATA register depends on the setting of "OpMode" field in

TSC_CTRL register. The samples acquired are accessed in "packed samples". The size of

each "packed sample" depends on which mode the touchscreen controller is operating in.

The TSC_DATA register can be accessed in 2 modes:

●Autoincrement

●Non autoincrement

To access the 128-sets buffer, the non autoincrement mode should be used.

76543 2 1 0

DATA

[11:0] DATA: data bytes from TSC FIFO

Table 16. Touchscreen controller DATA register

TSC_CTRL in

operation

mode

Number of

bytes to read

from

TSC_DATA_XYZ

Byte0 Byte1 Byte2 Byte3

000 4 [11:4] of X [3:0] of X

[11:8] of Y [7:0] of Y [7:0] of Z

001 3 [11:4] of X [3:0] of X

[11:8] of Y [7:0] of Y −

010 2 [11:4] of X [3:0] of X −−

011 2 [11:4] of Y [3:0] of Y −−

100 1 [7:0] of Z - −−

STMPE811 Touchscreen controller

Doc ID 14489 Rev 5 45/66

TSC_FRACTION_Z Touchscreen controller FRACTION_Z

Address: 0x56

Type: R

Reset: 0x00

Description: This register allows to select the range and accuracy of the pressure measurement

76543 2 1 0

RESERVED FRACTION_Z

[7:3] RESERVED

[2:0] FRACTION_Z:

000: Fractional part is 0, whole part is 8

001: Fractional part is 1, whole part is 7

010: Fractional part is 2, whole part is 6

011: Fractional part is 3, whole part is 5

100: Fractional part is 4, whole part is 4

101: Fractional part is 5, whole part is 3

110: Fractional part is 6, whole part is 2

111: Fractional part is 7, whole part is 1

Touchscreen controller STMPE811

46/66 Doc ID 14489 Rev 5

TSC_I_DRIVE Touchscreen controller drive I

Address: 0x58

Type: R/W

Reset: 0x00

Description: This register sets the current limit value of the touchscreen drivers

TSC_SHIELD Touchscreen controller shield

Address: 0x59

Type: R

Reset: 0x00

Description: Writing each bit would ground the corresponding touchscreen wire

76543 2 1 0

RESERVED DRIVE

[7:1] RESERVED

[0] DRIVE: maximum current on the touchscreen controller (TSC) driving channel

0: 20 mA typical, 35 mA max

1: 50 mA typical, 80 mA max

76543 2 1 0

RESERVED X+ X- Y+ Y-

[7:4] RESERVED

[3:0] SHIELD[3:0]:

Write 1 to GND X+, X-, Y+, Y- lines

STMPE811 Touchscreen controller programming sequence

Doc ID 14489 Rev 5 47/66

11 Touchscreen controller programming sequence

The following are the steps to configure the touchscreen controller (TSC):

a) Disable the clock gating for the touchscreen controller and ADC in the SYS_CFG2

b) Configure the touchscreen operating mode and the window tracking index.

c) A touch detection status may also be enabled through enabling the corresponding

interrupt flag. With this interrupt, the user is informed through an interrupt when

the touch is detected as well as lifted.

d) Configure the TSC_CFG register to specify the “panel voltage settling time”, touch

detection delays and the averaging method used.

e) A windowing feature may also be enabled through TSCWdwTRX, TSCWdwTRY,

TSCWdwBLX and TSCWdwBLY registers. By default, the windowing covers the

entire touch panel.

f) Configure the TSC_FIFO_TH register to specify the threshold value to cause an

interrupt. The corresponding interrupt bit in the interrupt module must also be

enabled. This interrupt bit should be masked off during data fetching from the

FIFO in order to prevent an unnecessary trigger of this interrupt. Upon completion

of the data fetching, this bit can be re-enabled

g) By default, the FIFO_RESET bit in the TSC_FIFO_CTRL_STA register holds the

FIFO in Reset mode. Upon enabling the touchscreen controller (through the EN

bit in TSC_CTRL), this FIFO reset is automatically deasserted. The FIFO status

may be observed from the TSC_FIFO_CTRL_STA register or alternatively through

the interrupt.

h) Once the data is filled beyond the FIFO threshold value, an interrupt is triggered

(assuming the corresponding interrupt is being enabled). The user is required to

continuously read out the data set until the current FIFO size is below the

threshold, then, the user may clear the interrupt flag. As long as the current FIFO

size exceeds the threshold value, an interrupt from the touchscreen controller is

sent to the interrupt module. Therefore, even if the interrupt flag is cleared, the

interrupt flag is automatically asserted, as long as the FIFO size exceeds the

threshold value.

i) The current FIFO size can be obtained from the TSC_FIFO_Sz register. This

information may assists the user in how many data sets are to be read out from

the FIFO, if the user intends to read all in one shot. The user may also read a data

set by a data set.

j) The TSC_DATA_X register holds the X-coordinates. This register can be used in

all touchscreen operating modes.

k) The TSC_DATA_Y register holds the Y-coordinates. TSC_DATA_Y register holds

the Y-coordinates.

l) The TSC_DATA_Z register holds the Z value. TSC_DATA_Z register holds the Z-

coordinates.

m) The TSCDATA_XYZ register holds the X, Y and Z values. These values are

packed into 4 bytes. This register can only be used when the touchscreen

operating mode is 000 and 001. This register is to facilitate less byte read.

n) For the TSC_FRACT_Z register, the user may configure it based on the

touchscreen panel resistance. This allows the user to specify the resolution of the

Touchscreen controller programming sequence STMPE811

48/66 Doc ID 14489 Rev 5

Z value. With the Z value obtained from the register, the user simply needs to

multiply the Z value with the touchscreen panel resistance to obtain the touch

resistance.

o) The TSC_DATA register allows facilitation of another reading format with minimum

I2C transaction overhead by using the non autoincrement mode (or equivalent

mode in SPI). The data format is the same as TSC_DATA_XYZ, with the

exception that all the data fetched are from the same address.

p) Enable the EN bit of the TSC_CTRL register to start the touch detection and data

acquisition.

q) During the auto-hibernate mode, a touch detection can cause a wake-up to the

device only when the TSC is enabled and the touch detect status interrupt mask is

enabled.

r) In order to prevent confusion, it is recommended that the user not mix the data

fetching format (TSC_DATA_X, TSC_DATA_Y, TSC_DATA_Z, TSC_DATA_XYZ

and TSC_DATA) between one reading and the next.

s) It is also recommended that the user should perform a FIFO reset and TSC

disabling when the ADC or TSC setting are reconfigured.

STMPE811 Temperature sensor

Doc ID 14489 Rev 5 49/66

12 Temperature sensor

The STMPE811 internal temperature sensor can be used as a reference for compensation

of the touchscreen parameters. Temperature measurement is optimised for temperature

from 0 °C to 85 °C.

TEMP_CTRL Temperature sensor setup

Address: 0x60

Type: R/W

Reset: 0x00

Description: Temperature sensor setup

Table 17. Touchscreen parameters

Address Register name Bit Function

0x60 TEMP_CTRL 8 Temperature sensor setup

0x61 TEMP_DATA 16 Temperature data access port

0x63 TEMP_TH 16 Threshold for temperature controlled interrupt

765 4 3 2 1 0

RESERVED THRES_RANGE THRES_EN ACQ_MOD ACQ ENABLE

[7:5] RESERVED

[4] THRES_RANGE:

'0' assert interrupt if temperature is >= threshold

'1' assert interrupt if otherwise

[3] THRES_EN: temperature threshold enable

[2] ACQ_MOD:

'0' to acquire temperature for once only

'1' to acquire temperature every 10mS

[1] ACQ

[0] ENABLE

Temperature sensor STMPE811

50/66 Doc ID 14489 Rev 5

TEMP_DATA Temperature data

Address: 0x61 is MSB, 0x62 is LSB

Type: R

Reset: 0x00

Description: Temperature data access port

TEMP_TH Temperature threshold

Address: 0x63 is MSB, 0x64 is LSB

Type: R/W

Reset: 0x00

Description: Threshold for temperature controlled interrupt

11109876543 2 1 0

TEMPERATURE

[11:0] TEMPERATURE: Temperature reading

Absolute temperature

= ( VIO * temperature [11:0] ) / 7.51 (12-bit ADC)

= ( VIO * temperature [9:0] ) / 7.51 (10-bit ADC)

Note that VIO is used as a reference in temperature acquisition.

Variations in VIO directly affect the accuracy of temperature acquired.

11109876543 2 1 0

TEMP_TH

[11:0] TEMP_TH: temperature threshold

STMPE811 GPIO controller

Doc ID 14489 Rev 5 51/66

13 GPIO controller

A total of 8 GPIOs are available in the STMPE811 port expander device. Most of the GPIOs

share physical pins with some alternate functions. The GPIO controller contains the

registers that allow the host system to configure each of the pins into either a GPIO, or one

of the alternate functions. Unused GPIOs should be configured as outputs to minimize

power consumption.

A group of registers are used to control the exact function of each of the 8 GPIOs. The

registers and their respective addresses are listed in the following table.

All GPIO registers are named as GPIO-x, where x represents the functional group.

Table 18. GPIO control registers

Address Register name Size

(bit) Function

0x10 GPIO_SET_PIN 8 Set pin register

0x11 GPIO_CLR_PIN 8 Clear pin state

0x12 GPIO_MP_STA 8 Monitor pin state

0x13 GPIO_DIR 8 Set pin direction

0x14 GPIO_ED 8 Edge detect status

0x15 GPIO_RE 8 Rising edge detection

enable

0x16 GPIO_FE 8 Falling edge detection

enable

0x17 GPIO_ALT_FUNCT 8 Alternate function register

76543 2 1 0

GPIO-7 GPIO-6 GPIO-5 GPIO-4 GPIO-3 GPIO-2 GPIO-1 GPIO-0

GPIO controller STMPE811

52/66 Doc ID 14489 Rev 5

GPIO_SET_PIN GPIO set pin register

Address: 0x10

Type: R/W

Reset: 0x00

Description: GPIO set pin register.

Writing 1 to this bit causes the corresponding GPIO to go to 1 state.

Writing 0 has no effect.

GPIO_CLR_PIN Clear pin state register

Address: 0x11

Type: R/W

Reset: 0x00

Description: GPIO clear pin state register.

Writing ‘1’ to this bit causes the corresponding GPIO to go to 0 state.

Writing ‘0’ has no effect.

GPIO_MP_STA GPIO monitor pin state register

Address: 0x12

Type: R/W

Reset: 0x00

Description: GPIO monitor pin state.

Reading this bit yields the current state of the bit. Writing has no effect.

GPIO_DIR GPIO set pin direction

Address: 0x13

Type: R/W

Reset: 0x00

Description: GPIO set pin direction register.

Writing ‘0’ sets the corresponding GPIO to input state, and ‘1’ sets it to output state.

All bits are ‘0’ on reset.

STMPE811 GPIO controller

Doc ID 14489 Rev 5 53/66

GPIO_ED_STA GPIO edge detect status

Address: 0x14

Type: R/W

Reset: 0x00

Description: GPIO edge detect status register. An edge transition has been detected.

GPIO_RE Rising edge register

Address: 0x15

Type: R/W

Reset: 0x00

Description: GPIO rising edge detection enable register.

Setting this bit to ‘1’ would enable the detection of the rising edge transition.

The detection would be reflected in the GPIO edge detect status register.

GPIO_FE Falling edge detection enable register

Address: 0x16

Type: R/W

Reset: 0x00

Description: Setting this bit to ‘1’ would enable the detection of the falling edge transition.

The detection would be reflected in the GPIO edge detect status register.

GPIO_ALT_FUNCT Alternate function register

Address: 0x17

Type: R/W

Reset: 0x0F

Description: Alternate function register. "‘0’ sets the corresponding pin to function as

touchscreen/ADC, and ‘1’ sets it into GPIO mode.

13.0.1 Power supply

The STMPE811 GPIO operates from a separate supply pin (VIO). This dedicated supply pin

provides a level-shifting feature to the STMPE811. The GPIO remains valid until VIO is

removed.

The host system may choose to turn off Vcc supply while keeping VIO supplied. However it is

not allowed to turn off supply to VIO, while keeping the Vcc supplied.

The touchscreen is always powered by VIO. For better resolution and noise immunity, VIO

above 2.8 V is advised.

GPIO controller STMPE811

54/66 Doc ID 14489 Rev 5

13.0.2 Power-up reset (POR)

The STMPE811 is equipped with an internal POR circuit that holds the device in reset state,

until the VIO supply input is valid. The internal POR is tied to the VIO supply pin.

On power-up reset, all GPIOs are set as input.

STMPE811 Maximum rating

Doc ID 14489 Rev 5 55/66

14 Maximum rating

Stressing the device above the ratings listed in the “Absolute maximum ratings” table may

cause permanent damage to the device. These are stress ratings only, and operation of the

device at these or any other conditions above those indicated in the operating sections of

this specification is not implied. Exposure to absolute maximum rating conditions for

extended periods may affect the device’s reliability.

Table 19. Absolute maximum ratings

Symbol Parameter Value Unit

VCC Supply voltage 4.5 V

VIO GPIO supply voltage 4.5 V

ESD ESD protection on each GPIO pin (air discharge) 4 kV

T Operating temperature -40 - 85 °C

TSTG Storage temperature -65 - 155 °C

TJThermal resistance junction-ambient 96 °C/W

Maximum rating STMPE811

56/66 Doc ID 14489 Rev 5

14.1 Recommended operating conditions

Table 20. Power consumption

Symbol Parameter Test condition

Value

Unit

Min Typ Max

Vcc Core supply voltage

Vio >= Vcc

1.65 −3.6 V

VIO I/O supply voltage 1.65 −3.6 V

ICC-active Core supply current

Touchscreen

controller at 100 Hz

sampling

VCC=1.8−3.3 V

−0.5 1.0 µA

IIO-active I/O supply current

Touchscreen

controller at 100 Hz

sampling

VIO =1.8V

−0.8 1.2 mA

IIO-active I/O supply current

Touchscreen

controller at 100 Hz

sampling

VIO =3.3V

−2.0 2.8 mA

ICC-

hibernate

Core supply current

Hibernate state, no

I2C/SPI activity

VCC =1.8V

−0.5 1 µA

IIO-hibernate I/O supply current

Hibernate state, no

I2C/SPI activity

VIO =1.8−3.3 V

−0.5 1 µA

Hibernate state, no

I2C/SPI activity

VIO =3.3V

−1.0 3.0 µA

STMPE811 Electrical specifications

Doc ID 14489 Rev 5 57/66

15 Electrical specifications

Table 21. DC electrical characteristics (-40 °C to 85 °C) all GPIOs comply to JEDEC

standard JESD-8-7)

Table 22. AC electrical characteristics (-40 °C to 85 °C)

Symbol Parameter Test condition

Value

Unit

Min Typ Max

VIL Input voltage low state VIO =1.8 −3.3 V -0.3 V −0.20 VIO V

VIH Input voltage high state VIO =1.8 −3.3 V 0.80 VIO −VIO +0.3V V

VOL Output voltage low state VIO = 1.8 V,

IOL = 4 mA

VIO = 3.3 V,

IOL = 8 mA

-0.3 V −0.15 VIO V

VOH

Output voltage high

state 0.85 VIO −−

VOL

(I2C/SPI) Output voltage low state VCC = 1.8 V,

IOL = 4 mA

VCC = 3.3 V,

IOL = 8 mA

-0.3 V −0.15 VCC V

VOH

(I2C/SPI)

Output voltage high

state 0.85 VCC −VCC +0.3V V

Symbol Parameter Test condition

Value

Unit

Min Typ Max

CLKI2Cmax I2C maximum SCLK VIO =1.8-3.3V 400 −−

kHz

CLKSPImax SPI maximum clock

VIO =1.8V 800 −−

kHz

VIO = 3.3 V 1000 −−

kHz

Bits

Electrical specifications STMPE811

58/66 Doc ID 14489 Rev 5

Table 23. ADC specification (-40 °C to 85 °C)

Table 24. Switch drivers specification

Parameter Test condition

Value

Unit

Min Typ Max

Full-scale input span 0 −Vref V

Absolute input range −−

VCC +0.2 V

Input capacitance −25 −pF

Leakage current −0.1 −µA

Resolution −12 −Bits

No missing codes 11 −Bits

Integral linearity error −±4−Bits

Offset error −±5−LSB

Gain error −±14 ±18 LSB

Noise Including internal Vref −70 −µVrms

Power supply rejection ratio −50 −dB

Throughput rate −180 −ksps

Parameter Test condition

Value

Unit

Min Typ Max

ON resistance X+, Y+ −5.5 −Ω

ON resistance X-, Y- −7.3 −Ω

Drive current Duration 100 ms −−

50 mA

STMPE811 Package mechanical data

Doc ID 14489 Rev 5 59/66

16 Package mechanical data

In order to meet environmental requirements, ST offers these devices in different grades of

ECOPACK® packages, depending on their level of environmental compliance. ECOPACK®

specifications, grade definitions and product status are available at: www.st.com.

ECOPACK® is an ST trademark.

SEATING PLANE C L A3 P—Q ddd C < ;d—d—d—d="" 2="" d="" pin="" #1="" id="" d1="" 0:030="" jljljl="" e2="" jliju="" 7="" h="" h="" r“\m="" e1="">

Package mechanical data STMPE811

60/66 Doc ID 14489 Rev 5

Figure 12. Package outline for QFN16 (3 x 3 x 1 mm) - 0.50 pitch

1. Drawing not to scale.

7185330_F

STMPE811 Package mechanical data

Doc ID 14489 Rev 5 61/66

Table 25. Package mechanical data for QFN16 (3x3x 1 mm) - 0.50 pitch

Symbol Millimeters

Min Typ Max

A 0.800.901.00

A1 −0.02 0.05

A3 −0.20 −

b 0.180.250.30

D 2.853.003.15

D1 −1.50 −

D2 See exposed pad variation

E 2.853.003.15

E1 −1.50 −

E2 See exposed pad variation

e 0.450.500.55

L 0.300.400.50

ddd −−

0.05

Table 26. Exposed pad variation

Symbol Millimeters

Min Typ Max

D2 1.70 1.80 1.90

E2 1.70 1.80 1.90

|:| |_| I—I 46L

Package mechanical data STMPE811

62/66 Doc ID 14489 Rev 5

Figure 13. Recommended footprint

1. Drawing not to scale.

Table 27. Footprint dimensions

Symbol

Millimeters

Min Typ Max

A−3.8 −

B−3.8 −

C−0.5 −

D−0.3 −

E−0.8 −

F−1.5 −

G−0.35 −

A0 a a ems :4 8 .2005 A0 130 mm BO 130 mm K0 1.11; 111.10 t COVER , m swarm HOLE PITCH CUMULANVE fOLERANCE 21120

STMPE811 Package mechanical data

Doc ID 14489 Rev 5 63/66

Figure 14. Carrier tape for QFN16 (3 x 3 x 1 mm) - 0.50 pitch

1. Drawing not to scale.

7875978

75.4 Max (Measured at (Measured at hub} 12.4 mo '

Package mechanical data STMPE811

64/66 Doc ID 14489 Rev 5

Figure 15. Reel information for QFN16 (3 x 3 x 1 mm) - 0.50 pitch

1. Drawing not to scale.

7875978_14

STMPE811 Revision history

Doc ID 14489 Rev 5 65/66

17 Revision history

Table 28. Document revision history

Date Revision Changes

09-Jun-2008 1 Initial release.

22-Apr-2009 2

Document status promoted from preliminary data to datasheet.

Modified: title and package silhouette in the cover page.

Section 6: STMPE811 registers, Section 7: System and identification

registers, Section 10: Touchscreen controller and Section 13: GPIO

controller: content reworked to improve readability, no technical

changes.

Updated: Figure 6, Ta bl e 3 , Section 14: Maximum rating and

Section 16: Package mechanical data.

22-Sep-2010 3 Modified:Table 11: Register summary map table and information

related to the TSC_DATA_X register.

10-Jan-2011 4

Updated: Table 11: Register summary map table and information

related to the ADC control register, Table 13: ADC controller register

summary table and removed Table 25.

18-Apr-2011 5 Updated: Temperature sensors registers information.

STMPE811

66/66 Doc ID 14489 Rev 5

Please Read Carefully:

Information in this document is provided solely in connection with ST products. STMicroelectronics NV and its subsidiaries (“ST”) reserve the

right to make changes, corrections, modifications or improvements, to this document, and the products and services described herein at any

time, without notice.

All ST products are sold pursuant to ST’s terms and conditions of sale.

Purchasers are solely responsible for the choice, selection and use of the ST products and services described herein, and ST assumes no

liability whatsoever relating to the choice, selection or use of the ST products and services described herein.

No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted under this document. If any part of this

document refers to any third party products or services it shall not be deemed a license grant by ST for the use of such third party products

or services, or any intellectual property contained therein or considered as a warranty covering the use in any manner whatsoever of such

third party products or services or any intellectual property contained therein.

UNLESS OTHERWISE SET FORTH IN ST’S TERMS AND CONDITIONS OF SALE ST DISCLAIMS ANY EXPRESS OR IMPLIED

WARRANTY WITH RESPECT TO THE USE AND/OR SALE OF ST PRODUCTS INCLUDING WITHOUT LIMITATION IMPLIED

WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE (AND THEIR EQUIVALENTS UNDER THE LAWS

OF ANY JURISDICTION), OR INFRINGEMENT OF ANY PATENT, COPYRIGHT OR OTHER INTELLECTUAL PROPERTY RIGHT.

UNLESS EXPRESSLY APPROVED IN WRITING BY AN AUTHORIZED ST REPRESENTATIVE, ST PRODUCTS ARE NOT

RECOMMENDED, AUTHORIZED OR WARRANTED FOR USE IN MILITARY, AIR CRAFT, SPACE, LIFE SAVING, OR LIFE SUSTAINING

APPLICATIONS, NOR IN PRODUCTS OR SYSTEMS WHERE FAILURE OR MALFUNCTION MAY RESULT IN PERSONAL INJURY,

DEATH, OR SEVERE PROPERTY OR ENVIRONMENTAL DAMAGE. ST PRODUCTS WHICH ARE NOT SPECIFIED AS "AUTOMOTIVE

GRADE" MAY ONLY BE USED IN AUTOMOTIVE APPLICATIONS AT USER’S OWN RISK.

Resale of ST products with provisions different from the statements and/or technical features set forth in this document shall immediately void

any warranty granted by ST for the ST product or service described herein and shall not create or extend in any manner whatsoever, any

liability of ST.

ST and the ST logo are trademarks or registered trademarks of ST in various countries.

Information in this document supersedes and replaces all information previously supplied.

The ST logo is a registered trademark of STMicroelectronics. All other names are the property of their respective owners.

STMicroelectronics group of companies

Australia - Belgium - Brazil - Canada - China - Czech Republic - Finland - France - Germany - Hong Kong - India - Israel - Italy - Japan -

Malaysia - Malta - Morocco - Philippines - Singapore - Spain - Sweden - Switzerland - United Kingdom - United States of America

STMicroelectronics 的 STMPE811 规格书

信息

帮助

联系我们

关注我们