Molex 的 68783-0016 Prod Spec 规格书

molex
PRODUCT SPECIFICATION
REVISION: ECR/ECN INFORMATION: TITLE:
DisplayPort 1.3 HBR3
Plug to Plug Cable Assembly
SHEET No.
A
EC No:
1
of
8
DATE:
05/25/2018
DOCUMENT NUMBER: CREATED / REVISED BY: CHECKED BY: APPROVED BY:
PS-68783-0016
CISSY WANG LIU LIHUA FRED NIE
Molex is a registered trademark of Molex, LLC in the United States of America and may be registered in other countries; all other trademarks listed herein belong to their respective owners.
TITLE
DisplayPort 1.3 HBR3
Plug to Plug Cable Assembly
Table of Contents
1.0 SCOPE
2.0 PRODUCT DESCRIPTION
3.0 PRODUCT SPECIFICATIONS
3.1 Rating voltage
3.2 Rating current
3.3 Temperature
4.0 QUALIFICATION
5.0 PERFORMANCE
5.1 Electrical characteristics
5.2 Mechanical characteristics
5.3 Environmental characteristics
molex
PRODUCT SPECIFICATION
REVISION: ECR/ECN INFORMATION: TITLE:
DisplayPort 1.3 HBR3
Plug to Plug Cable Assembly
SHEET No.
A
EC No:
2
of
8
DATE:
05/25/2018
DOCUMENT NUMBER: CREATED / REVISED BY: CHECKED BY: APPROVED BY:
PS-68783-0016
CISSY WANG LIU LIHUA FRED NIE
Molex is a registered trademark of Molex, LLC in the United States of America and may be registered in other countries; all other trademarks listed herein belong to their respective owners.
1.0 SCOPE
This specification covers the requirements for DisplayPort Plug to Plug Cable Assy.
2.0 PRODUCT DESCRIPTION
See the sales drawing for product shape; dimension and materials, the other section of this specification for the
necessary referenced document and specification. The part number serial covered in this specification are as
follow table:
Molex Series Detail
68783 DisplayPort Plug to Plug Cable Assembly
3.0 PRODUCT SPECIFICATIONS
3.1 Rated voltage (Maximum): 30V AC (rms)
3.2 Rated current (Maximum): 0.5A AC (rms)/DC
3.3 Temperature
Operating temperature range: -20°C to +80°C (Without loss function)
Storage temperature range: -20°C to + 80°C (Without loss function)
4.0 QUALIFICATION
Laboratory conditions and sample selection are in accordance with EIA-364-1000.01
molex
PRODUCT SPECIFICATION
REVISION: ECR/ECN INFORMATION: TITLE:
DisplayPort 1.3 HBR3
Plug to Plug Cable Assembly
SHEET No.
A
EC No:
3
of
8
DATE:
05/25/2018
DOCUMENT NUMBER: CREATED / REVISED BY: CHECKED BY: APPROVED BY:
PS-68783-0016
CISSY WANG LIU LIHUA FRED NIE
Molex is a registered trademark of Molex, LLC in the United States of America and may be registered in other countries; all other trademarks listed herein belong to their respective owners.
5.0 PERFORMANCE
5.1 ELECTRICAL CHARACTERISTICS
Test Description Test Condition Performance Requirement
Low Level
Contact
Resistance
(Apply to
DisplayPort plug
connector kit)
Mated connectors
Contact: measure by dry circuit, 20
mV
Max., 10 mA
(ANSI/EIA 364-23)
30 milliohm Max.
Shell: measure by dry circuit, 5V Max., 100
mA
(ANSI/EIA-364-06A-83) 50 milliohm Max.
Dielectric
Withstanding
Voltage
(Apply to
DisplayPort plug
connector kit)
Unmated connector
Apply 500V AC (rms.) for 1 minute
between adjacent terminal and ground.
Mated connectors
Apply 300V AC for 1 minute between
adjacent terminal and ground.
(ANSI/EIA 364-20)
No breakdown
Insulation
Resistance
(Apply to
DisplayPort plug
connector kit)
Unmated connector
Apply 500V DC between adjacent terminal
and ground.
(ANSI/EIA 364-21, method 302)
100megohm Min.
Mated connectors
Apply 150V DC between adjacent terminal
and ground.
(ANSI/EIA 364-21, method 302)
10megohm Min.
Contact
Current Rating
(Apply to
DisplayPort plug
connector kit)
Initial ambient temperature: 55°C Maximum
After temperature changed: 85°C
Maximum
(ANSI/EIA-364-70,TP-70)
0.5A Min.
Applied
Voltage Rating
(Apply to
DisplayPort plug
connector kit)
40V AC (rms.) continuous maximum, on
any signal pin with respect to the shield. No breakdown
Electrostatic
Discharge
(Apply to
DisplayPort plug
connector kit)
Test unmated each connector from 1 kV to
8 kV in 1 kV steps using 8 mm ball probe.
(IEC 61000-4-2) No evidence of discharge to contacts at 8kV
molex ‘ 73h Ul< [win/hm="" mm="" awlsumi="" ,="">‘X| NI IT \ ,n [.1034
PRODUCT SPECIFICATION
REVISION: ECR/ECN INFORMATION: TITLE:
DisplayPort 1.3 HBR3
Plug to Plug Cable Assembly
SHEET No.
A
EC No:
4
of
8
DATE:
05/25/2018
DOCUMENT NUMBER: CREATED / REVISED BY: CHECKED BY: APPROVED BY:
PS-68783-0016
CISSY WANG LIU LIHUA FRED NIE
Molex is a registered trademark of Molex, LLC in the United States of America and may be registered in other countries; all other trademarks listed herein belong to their respective owners.
Time Domain
differential
Impedance
Rise time: 130ps. (20%-80%)
Signal to ground pin ratio per
Display Port designation.
Differential measurement specimen
environment impedance=100 ohms
differential
Source side receptacle connector mounted
on a controlled impedance PCB fixture.
(ANSI/EIA-364-108 Draft Proposal)
Connector &
wire
management 100±10% Ω
Cable area(raw
cable) 100±5% Ω
Cross Talk
Near End Noise (NEN) shall be defined in
frequency domain and cover the bandwidth
of up to 7GHz.
where:
f is given in GHz
f0=1.35GHz
The Far End Noise shall be defined in
frequency domain.
where:
f is given in GHz
f0=2.7GHz
Differential
Skew
Intra-Pair Skew
Skew= |TIME(Signal x+)-TIME(Signal x-)|
(Cable area only)
Display Port designation.
Differential measurement specimen
environment impedance:
100 ohms differential
Source-side receptacle connector mounted
on a controlled impedance PCB fixture.
(See fig. Below)
Intra-Pair Skew:
50ps Max.
@TDR 130 ps(20%~80%)
Inter-Pair Skew
Skew= |TIME(Signal x+)-TIME(Signal x-)|
(Cable area only)
Display Port designation.
Differential measurement specimen
environment impedance:
100 ohms differential
Source-side receptacle connector mounted
on a controlled impedance PCB fixture.
(See fig. Below)
Inter-Pair Skew:
4 ns Max.
@TDR 130 ps(20%~80%)
molex'“ ’/ / 78.7X (770.072: 0.1< y="" amt/81:="" v="" 3="" ,="" .="" .="" w="" .fi="" 1“="" mom/(73.:="" #63.="" jaw]="" ‘45;="">< gm="" «_="" 3="" ‘="" d‘gnaisawlvns="" netwurkanah/zev="" }="" oscflloscope“="" —="" siqha‘x‘“="" te“="" cable="" bigna‘x-r‘="" .="" p-.="" 3="" 1="" 1="" fl="" “351="" fm“="" ‘="" tes1="" mee="" a!="" smitten="" test="" cable="" sign!="" tune="" dumam="" dxfi‘ennual="" impadanca="" crass="" talk="" fext‘="" sign!="" skew="" measurement="" configuxanun="" attanuanun="" measuxemem="" configuxauun‘="">
PRODUCT SPECIFICATION
REVISION: ECR/ECN INFORMATION: TITLE:
DisplayPort 1.3 HBR3
Plug to Plug Cable Assembly
SHEET No.
A
EC No:
5
of
8
DATE:
05/25/2018
DOCUMENT NUMBER: CREATED / REVISED BY: CHECKED BY: APPROVED BY:
PS-68783-0016
CISSY WANG LIU LIHUA FRED NIE
Molex is a registered trademark of Molex, LLC in the United States of America and may be registered in other countries; all other trademarks listed herein belong to their respective owners.
Insertion Loss
Insertion Loss:
Connect cable to connector on test fixture,
Measure by Network Analyzer.
(See fig. Below)
where:
f is given in GHz
f0=1.35GHz
(For High-bit-rate Cable Assembly)
Return Loss
Return Loss:
Connect cable to connector on test fixture,
Measure by Network Analyzer.
(See fig. Below)
where:
f is given in GHz
f0=1.35GHz
(For High-bit-rate Cable Assembly)
molex
PRODUCT SPECIFICATION
REVISION: ECR/ECN INFORMATION: TITLE:
DisplayPort 1.3 HBR3
Plug to Plug Cable Assembly
SHEET No.
A
EC No:
6
of
8
DATE:
05/25/2018
DOCUMENT NUMBER: CREATED / REVISED BY: CHECKED BY: APPROVED BY:
PS-68783-0016
CISSY WANG LIU LIHUA FRED NIE
Molex is a registered trademark of Molex, LLC in the United States of America and may be registered in other countries; all other trademarks listed herein belong to their respective owners.
5.2 MECHANICAL CHARACTERISTICS
Test Description Test Condition Performance Requirement
Cable Flexing
Rotate the specimen up to 100 cycles in each
of 2 planes at the speed of 12 to 14 complete
cycles ( of 180 total traverse ) per minute, see
paragraph 6 Mandrel Diameter :
X =3.7 × Cable Diameter.
(ANSI/EIA-364-41, Condition Ⅰ)
Appearance No Damage
Discontinuity 1 microsecond
Max.
Dielectric
Strength and
Insulation
Resistance
Conform to item of
Dielectric
Withstanding
Voltage and
Insulation
Resistance
Insertion Force/
Withdrawal Force
(without latch type)
Insert and withdraw connectors at a rate of
25±3mm per minute.
(ANSI/EIA-364-13)
Insertion Force 44.1N {4.5 kgf} Max.
Withdraw Force
After 2,000
times insert/
withdraw
9.8N {1.0 kgf} Min.
39.2N {4.0 kgf} Max.
After 10,000
times insert/
withdraw
4.9N {0.5 kgf} Min.
39.2N {4.0 kgf} Max.
Latch Strength
(with latch type)
Mate connectors, apply axial pull-out force in
the axial direction at the speed rate of 13
mm/minute until the latch is disengaged or
damaged.
(ANSI/EIA-364-98)
Appearance No Damage on both
connectors
Pull force 49.0N {0.5 kgf} Min.
Durability
(Apply to DisplayPort
plug connector kit)
Automatic cycling: 10,000 cycles at
100±50 cycles per hour.
(ANSI/EIA-364-9)
Contact
Resistance
Change form initial
requirement :
Contact:30 milliohm
Max.
Shell:50 milliohm
Max.
molex
PRODUCT SPECIFICATION
REVISION: ECR/ECN INFORMATION: TITLE:
DisplayPort 1.3 HBR3
Plug to Plug Cable Assembly
SHEET No.
A
EC No:
7
of
8
DATE:
05/25/2018
DOCUMENT NUMBER: CREATED / REVISED BY: CHECKED BY: APPROVED BY:
PS-68783-0016
CISSY WANG LIU LIHUA FRED NIE
Molex is a registered trademark of Molex, LLC in the United States of America and may be registered in other countries; all other trademarks listed herein belong to their respective owners.
Vibration
(Apply to DisplayPort
plug connector kit)
Amplitude : 1.52 mm P-P or 147m/s²{15G}
Sweep time : 50-2000-50Hz in 20 minutes
Duration : 12 times in each(total of 36 times)
X, Y, Z axes.
Electrical load : DC 100 mA current shall be
Flowed during the test.
(ANSI/EIA-364-28, condition Ⅲ,
Method 5A)
Appearance No Damage
Contact
Resistance
Change form initial
requirement :
Contact:
30 milliohm
Max.
Shell:50 milliohm
Max.
Discontinuity 1 microseconds Max.
Shock
(Apply to DisplayPort
plug connector kit)
Pulse width : 11 msec.,
Wave form : half sine, 490 m/s² {50G},
3 strokes in each X, Y, Z axes.
(ANSI/EIA-364-27 Condition A)
Appearance
No Damage
Discontinuity
1 microseconds
maximum
Pull Force Cable pull-out (static) force: 5kgf for one minute
No damage, no open and short occur
5.3 ENVIRONMENTAL CHARACTERISTIC
Test
Description Test Procedure Performance Requirement
Temperature
Shock
(Apply to
DisplayPort
plug
connector
kit)
Mate connectors and subject to the following
conditions for 10 cycles. Upon completion of
the exposure period, the test specimens
shall be conditioned at ambient room
conditions for 1 to 2 hours, after which the
specified measurements shall be performed.
1cycle -55±3°C for 30 minutes
+85±3°C for 30 minutes
(Transit time shall be with in 3 minutes)
(ANSI/EIA-364-32, Condition
Ⅰ
)
Appearance No Damage
Contact
Resistance
Change form initial
requirement :
Contact:
30 milliohm Max.
Shell: 50 milliohm Max.
Humidity
(Apply to
DisplayPort
plug
A) Mate connectors together and perform
the test as follows.
Temperature : +25 to +85°C
Relative Humidity : 80% to 95%
Duration : 4 cycles (96 hours)
Appearance No Damage
molex
PRODUCT SPECIFICATION
REVISION: ECR/ECN INFORMATION: TITLE:
DisplayPort 1.3 HBR3
Plug to Plug Cable Assembly
SHEET No.
A
EC No:
8
of
8
DATE:
05/25/2018
DOCUMENT NUMBER: CREATED / REVISED BY: CHECKED BY: APPROVED BY:
PS-68783-0016
CISSY WANG LIU LIHUA FRED NIE
Molex is a registered trademark of Molex, LLC in the United States of America and may be registered in other countries; all other trademarks listed herein belong to their respective owners.
connector
kit) Upon completion of the test, specimens shall
be conditioned at ambient room conditions
for 24 hours, after which the specified
measurements shall be performed.
(ANSI/EIA-364-31)
Contact
Resistance
Change form initial
requirement :
Contact:
30 milliohm Max.
Shell: 50 milliohm Max.
B) Unmate connectors and perform the test
as follows.
Temperature : +25 to +85°C
Relative Humidity : 80 to 95%
Duration : 4 cycles (96 hours)
Upon completion of the test, specimens shall
be conditioned at ambient room conditions
for 24 hours, after which the specified
measurements shall be performed.
(ANSI/EIA-364-31)
Appearance No Damage
Dielectric
Withstanding
Voltage and
Insulation
Resistance
Conform to item of
Dielectric Withstanding
Voltage and Insulation
Resistance
Heat
Resistance
Mate connectors and expose to 105±2°C for
250 hours. Upon completion of the exposure
period, the test specimens shall be
conditioned at ambient room conditions for 1
to 2 hours, after which the specified
measurements shall be performed.
(ANSI/EIA-364-17, Condition 4, Method A)
Appearance No Damage
Contact
Resistance
Change form initial
requirement :
Contact:30 milliohm
Max.
Shell:50 milliohm
Max.
Salt Spray
Mate connector and expose to the following
salt mist condition. Upon completion of the
exposure period, salt deposits shall be
removed by a gentle wash or dip in running
water, after which the specified
measurements shall be performed.
Nacl solution:
Concentration: 5%±1%.
Spray time: 24h±1h.
Ambient Temperature: 35 ºC ±2ºC.
EIA-364-26
Appearance No Damage
Contact
Resistance
Change form initial
requirement :
Contact:30 milliohm
Max.
Shell:50 milliohm
Max.