Texas Instruments 的 SN54LV393A, SN74LV393A 规格书

_[ U l [ J [ 1 lo" Supports Partial-Power—Down-Mode 105 I: 4 ii 1 Operation 10c[ 5 ‘0] Dual 4-Bit Binary Counters With Individual 109': 6 91 Clocks GND [ 7 a ] Direct Clear for Each 4-Bit Counter Can Significantly Improve System Densities by Reducing Counter Package Count by 50 Percent Latch-Up Performance Exceeds 100 mA Per ‘ ‘ JESD 78, Class II ESD Protection Exceeds JESD 22 _ zooo-v Human-Body Model (A114-A) E _ zoo-v Machine Model (A115-A) E _ 1ooo-v Charged-Device Model (0101) E descrip on/ordering inlormation I: The ’LV393A devices contain eight lllprllops and additional gating to implement two individual 47bit counters in a single package. These devices are designed for 27V to 5.5V VCC operation. ORDERING INFORMATION TA WAG“ pi'é'ii'lflféin 3323:: Tube ml 50 SN74LV393AD SO’C ’ D Reel ol 2500 SN74LV393ADR wag” SOP , NS Reel ol 2000 SN74LV393ANSR 74LV393A SSOP , DB Reel ol 2000 SN74LV393ADBR LvasaA 40°C m 8550 Tube ml 90 SN74LV393APW TSSOF , PW Reel ol 2000 SN74LV393APWR LV393A Reel ml 250 SN74LV393APWT TVSOF , DGV Reel ol 2000 SN74LV393ADGVR LvasaA CDlP , J Tube ml 25 SNJ54LV393AJ SNJSALVGSB 755°C to 125%: CFP , w Tube dl 150 SNJ54LV393AW SNJSALVGSB LCCC , FK Tube ml 55 SNJ54LV393AFK SNJSALVGSB tPackage drawmgs, standard packing quanlrlres, thermal data symbollzailon‘ and PCB guidelines are available at wwwtl.com/sc/package, Please be aware lnal an rmperlanl notice concernlng avarlamlrly, standard warranty, and use Texas lnslrumenls semreenducmr producLs and dlsclalmers thereto appears at Me end ol this data sh ‘4‘ TEXAS Cepyngnl r: 2005, INSTRUMENTS POST omcz aox 555303 - DALLAS TEXAS 752s5
 
   
SCLS457D − FEBRUARY 2001 − REVISED APRIL 2005
1
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
D2-V to 5.5-V VCC Operation
DMax tpd of 10 ns at 5 V
DTypical VOLP (Output Ground Bounce)
<0.8 V at VCC = 3.3 V, TA = 25°C
DTypical VOHV (Output VOH Undershoot)
>2.3 V at VCC = 3.3 V, TA = 25°C
DIoff Supports Partial-Power-Down-Mode
Operation
DDual 4-Bit Binary Counters With Individual
Clocks
DDirect Clear for Each 4-Bit Counter
DCan Significantly Improve System
Densities by Reducing Counter Package
Count by 50 Percent
DLatch-Up Performance Exceeds 100 mA Per
JESD 78, Class II
DESD Protection Exceeds JESD 22
− 2000-V Human-Body Model (A114-A)
− 200-V Machine Model (A115-A)
− 1000-V Charged-Device Model (C101)
description/ordering information
The ’LV393A devices contain eight flip-flops and
additional gating to implement two individual 4-bit
counters in a single package. These devices are
designed for 2-V to 5.5-V VCC operation.
ORDERING INFORMATION
TAPACKAGE†ORDERABLE
PART NUMBER TOP-SIDE
MARKING
SOIC − D
Tube of 50 SN74LV393AD
LV393A
SOIC − D Reel of 2500 SN74LV393ADR LV393A
SOP − NS Reel of 2000 SN74LV393ANSR 74LV393A
−40°C to 85°C
SSOP − DB Reel of 2000 SN74LV393ADBR LV393A
−40°C to 85°CTube of 90 SN74LV393APW
TSSOP − PW Reel of 2000 SN74LV393APWR LV393A
TSSOP − PW
Reel of 250 SN74LV393APWT
LV393A
TVSOP − DGV Reel of 2000 SN74LV393ADGVR LV393A
CDIP − J Tube of 25 SNJ54LV393AJ SNJ54LV393AJ
−55°C to 125°CCFP − W Tube of 150 SNJ54LV393AW SNJ54LV393AW
−55 C to 125 C
LCCC − FK Tube of 55 SNJ54LV393AFK SNJ54LV393AFK
†Package drawings, standard packing quantities, thermal data, symbolization, and PCB design
guidelines are available at www.ti.com/sc/package.
Copyright 2005, Texas Instruments Incorporated
Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of
Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet.
SN54LV393A ...J OR W PACKAGE
SN74LV393A . . . D, DB, DGV, NS, OR PW PACKAGE
(TOP VIEW)
1
2
3
4
5
6
7
14
13
12
11
10
9
8
1CLK
1CLR
1QA
1QB
1QC
1QD
GND
VCC
2CLK
2CLR
2QA
2QB
2QC
2QD
SN54LV393A . . . FK PACKAGE
(TOP VIEW)
NC − No internal connection
3212019
910111213
4
5
6
7
8
18
17
16
15
14
2CLR
NC
2QA
NC
2QB
1QA
NC
1QB
NC
1QC
1CLR
1CLK
NC
V
2CLK
D
GND
NC
CC
1Q
D
2Q
C
2Q
    !"#$ $%$ &
 $'("%$ !((#$ % ' )!*+%$ %#, &(! $'(" 
)#'%$ )#( # #(" ' #-% $(!"#$ %$%( .%((%$/,
&(!$ )(#$0 # $ $##%(+/ $+!# #$0 ' %++
)%(%"##(,
 
   
SCLS457D − FEBRUARY 2001 − REVISED APRIL 2005
2POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
description/ordering informaton (continued)
These devices comprise two independent 4-bit binary counters, each having a clear (CLR) and a clock (CLK)
input. These devices change state on the negative-going transition of the CLK pulse. N-bit binary counters can
be implemented with each package, providing the capability of divide by 256. The ’LV393A devices have parallel
outputs from each counter stage so that any submultiple of the input count frequency is available for system
timing signals.
These devices are fully specified for partial-power-down applications using Ioff. The Ioff circuitry disables the
outputs, preventing damaging current backflow through the devices when they are powered down.
FUNCTION TABLE
INPUTS
FUNCTION
CLK CLR
FUNCTION
↑LNo change
↓L Advance to next stage
X H All outputs L
logic diagram, each counter (positive logic)
R
T
QA
CLR
CLK
R
T
QB
R
T
QC
R
T
QD
Q
Q
Q
Q
_H_H a“ _ INSTRUMENTS ‘4; TEXAS
 
   
SCLS457D − FEBRUARY 2001 − REVISED APRIL 2005
3
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
timing diagram
CLK
CLR
QA
QB
QC
QD
Clear
Outputs
Count Up
absolute maximum ratings over operating free-air temperature range (unless otherwise noted)†
Supply voltage range, VCC −0.5 V to 7 V. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Input voltage range, VI (see Note 1) −0.5 V to 7 V. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Output voltage range applied in high or low state, VO (see Notes 1 and 2) −0.5 V to VCC + 0.5 V. . . . . . . . . .
Output voltage range applied in power-off state, VO (see Note 1) −0.5 V to 7 V. . . . . . . . . . . . . . . . . . . . . . . . .
Input clamp current, IIK (VI < 0) −20 mA. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Output clamp current, IOK (VO < 0) −50 mA. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Continuous output current, IO (VO = 0 to VCC) ±25 mA. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Continuous current through VCC or GND ±50 mA. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Package thermal impedance, θJA (see Note 3): D package 86°C/W. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
DB package 96°C/W. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
DGV package 127°C/W. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
NS package 76°C/W. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
PW package 113°C/W. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Storage temperature range, Tstg −65°C to 150°C. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
†Stresses beyond those listed under “absolute maximum ratings” may cause permanent damage to the device. These are stress ratings only, and
functional operation of the device at these or any other conditions beyond those indicated under “recommended operating conditions” is not
implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability.
NOTES: 1. The input and output negative-voltage ratings may be exceeded if the input and output current ratings are observed.
2. This value is limited to 7 V maximum.
3. The package thermal impedance is calculated in accordance with JESD 51-7.
input transmon use or can rate ‘9 TEXAS INSTRUMENTS
 
   
SCLS457D − FEBRUARY 2001 − REVISED APRIL 2005
4POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
recommended operating conditions (see Note 4)
SN54LV393A SN74LV393A
UNIT
MIN MAX MIN MAX
UNIT
VCC Supply voltage 2 5.5 2 5.5 V
VCC = 2 V 1.5 1.5
VIH
VCC = 2.3 V to 2.7 V VCC ×0.7 VCC ×0.7
V
VIH High-level input voltage VCC = 3 V to 3.6 V VCC ×0.7 VCC ×0.7 V
VCC = 4.5 V to 5.5 V VCC ×0.7 VCC ×0.7
VCC = 2 V 0.5 0.5
VIL
VCC = 2.3 V to 2.7 V VCC ×0.3 VCC ×0.3
V
VIL Low-level input voltage VCC = 3 V to 3.6 V VCC ×0.3 VCC ×0.3 V
VCC = 4.5 V to 5.5 V VCC ×0.3 VCC ×0.3
VIInput voltage 0 5.5 0 5.5 V
VOOutput voltage 0 VCC 0 VCC V
VCC = 2 V −50 −50 µA
IOH
VCC = 2.3 V to 2.7 V −2 −2
IOH High-level output current VCC = 3 V to 3.6 V −6 −6 mA
VCC = 4.5 V to 5.5 V −12 −12
mA
VCC = 2 V 50 50 µA
IOL
VCC = 2.3 V to 2.7 V 2 2
IOL Low-level output current VCC = 3 V to 3.6 V 6 6 mA
VCC = 4.5 V to 5.5 V 12 12
mA
VCC = 2.3 V to 2.7 V 200 200
∆t/∆vInput transition rise or fall rate VCC = 3 V to 3.6 V 100 100 ns/V
∆t/∆v
VCC = 4.5 V to 5.5 V 20 20
ns/V
TAOperating free-air temperature −55 125 −40 85 °C
NOTE 4: All unused inputs of the device must be held at VCC or GND to ensure proper device operation. Refer to the TI application report,
Implications of Slow or Floating CMOS Inputs, literature number SCBA004.
electrical characteristics over recommended operating free-air temperature range (unless
otherwise noted)
PARAMETER
TEST CONDITIONS
VCC
SN54LV393A SN74LV393A
UNIT
PARAMETER
TEST CONDITIONS
VCC MIN TYP MAX MIN TYP MAX
UNIT
IOH = −50 µA2 V to 5.5 V VCC−0.1 VCC−0.1
VOH
IOH = −2 mA 2.3 V 2 2
V
VOH IOH = −6 mA 3 V 2.48 2.48 V
IOH = −12 mA 4.5 V 3.8 3.8
IOL = 50 µA2 V to 5.5 V 0.1 0.1
VOL
IOL = 2 mA 2.3 V 0.4 0.4
V
VOL IOL = 6 mA 3 V 0.44 0.44 V
IOL = 12 mA 4.5 V 0.55 0.55
IIVI = 5.5 V or GND 0 to 5.5 V ±1±1µA
ICC VI = VCC or GND, IO = 0 5.5 V 20 20 µA
Ioff VI or VO = 0 to 5.5 V 0 5 5 µA
CiVI = VCC or GND 3.3 V 1.8 1.8 pF
& & $'("%$ $#($ )(! $ # '("%1# (
#0$ )%# ' #1#+)"#$, %(%#( %% %$ #(
)#'%$ %(# #0$ 0%+, #-% $(!"#$ (##(1# # (0 
%$0# ( $$!# ## )(! .! $#,
‘4‘ TEXAS INSTRUMENTS
 
   
SCLS457D − FEBRUARY 2001 − REVISED APRIL 2005
5
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
timing requirements over recommended operating free-air temperature range, VCC = 2.5 V ±0.2 V
(unless otherwise noted) (see Figure 1)
TA = 25°C SN54LV393A SN74LV393A
UNIT
MIN MAX MIN MAX MIN MAX
UNIT
tw
Pulse duration
CLK high or low 555
ns
twPulse duration CLR high 555ns
tsu Setup time CLR inactive before CLK↓6 6 6 ns
timing requirements over recommended operating free-air temperature range, VCC = 3.3 V ±0.3 V
(unless otherwise noted) (see Figure 1)
TA = 25°C SN54LV393A SN74LV393A
UNIT
MIN MAX MIN MAX MIN MAX
UNIT
tw
Pulse duration
CLK high or low 555
ns
twPulse duration CLR high 555ns
tsu Setup time CLR inactive before CLK↓5 5 5 ns
timing requirements over recommended operating free-air temperature range, VCC = 5 V ±0.5 V
(unless otherwise noted) (see Figure 1)
TA = 25°C SN54LV393A SN74LV393A
UNIT
MIN MAX MIN MAX MIN MAX
UNIT
tw
Pulse duration
CLK high or low 555
ns
twPulse duration CLR high 555ns
tsu Setup time CLR inactive before CLK↓4 4 4 ns
switching characteristics over recommended operating free-air temperature range,
VCC = 2.5 V ±0.2 V (unless otherwise noted) (see Figure 1)
PARAMETER
FROM
TO
LOAD
TA = 25°C SN54LV393A SN74LV393A
UNIT
PARAMETER
FROM
(INPUT)
TO
(OUTPUT)
LOAD
CAPACITANCE MIN TYP MAX MIN MAX MIN MAX
UNIT
fmax
CL = 15 pF 50* 90* 40* 40
MHz
fmax CL = 50 pF 30 70 25 25 MHz
QA7.1* 17.7* 1* 20.5* 1 20.5
tpd
CLK
QB8.5* 20.3* 1* 23.5* 1 23.5
tpd CLK QCC
L
= 15 pF 10* 22.5* 1* 26* 1 26 ns
QD
CL = 15 pF
11.1* 24.2* 1* 28* 1 28
ns
tPHL CLR Qn6.7* 14.8* 1* 17* 1 17
QA9.3 21.3 1 24.5 1 24.5
tpd
CLK
QB10.9 23.9 1 27.5 1 27.5
tpd CLK QCCL = 50 pF 12.3 26.1 1 30 1 30 ns
QD
CL = 50 pF
13.4 27.8 1 32 1 32
ns
tPHL CLR Qn9.1 17.4 1 20 1 20
* On products compliant to MIL-PRF-38535, this parameter is not production tested.
& & $'("%$ $#($ )(! $ # '("%1# (
#0$ )%# ' #1#+)"#$, %(%#( %% %$ #(
)#'%$ %(# #0$ 0%+, #-% $(!"#$ (##(1# # (0 
%$0# ( $$!# ## )(! .! $#,
b TEXAS INSTRUMENTS
 
   
SCLS457D − FEBRUARY 2001 − REVISED APRIL 2005
6POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
switching characteristics over recommended operation free-air temperature range,
VCC = 3.3 V ± 0.3 V (unless otherwise noted) (see Figure 1)
PARAMETER
FROM
TO
LOAD
TA = 25°C SN54LV393A SN74LV393A
UNIT
PARAMETER
FROM
(INPUT)
TO
(OUTPUT)
LOAD
CAPACITANCE MIN TYP MAX MIN MAX MIN MAX
UNIT
fmax
CL = 15 pF 75* 130* 65* 65
MHz
fmax CL = 50 pF 45 105 35 35 MHz
QA5.1* 13.2* 1* 15.5* 1 15.5
tpd
CLK
QB6* 15.8* 1* 18.5* 1 18.5
tpd CLK QCC
L
= 15 pF 7* 18* 1* 21* 1 21 ns
QD
CL = 15 pF
7.7* 19.7* 1* 23* 1 23
ns
tPHL CLR Qn5.1* 12.3* 1* 14.5* 1 14.5
QA6.7 16.7 1 19 1 19
tpd
CLK
QB7.8 19.3 1 22 1 22
tpd CLK QCCL = 50 pF 8.7 21.5 1 24.5 1 24.5 ns
QD
CL = 50 pF
9.5 23.2 1 26.5 1 26.5
ns
tPHL CLR Qn6.8 15.8 1 18 1 18
* On products compliant to MIL-PRF-38535, this parameter is not production tested.
switching characteristics over recommended operating free-air temperature range,
VCC = 5 V ± 0.5 V (unless otherwise noted) (see Figure 1)
PARAMETER
FROM
TO
LOAD
TA = 25°C SN54LV393A SN74LV393A
UNIT
PARAMETER
FROM
(INPUT)
TO
(OUTPUT)
LOAD
CAPACITANCE MIN TYP MAX MIN MAX MIN MAX
UNIT
fmax
CL = 15 pF 125* 185* 105* 105
MHz
fmax CL = 50 pF 85 150 75 75 MHz
QA3.7* 8.5* 1* 10* 1 10
tpd
CLK
QB4.3* 9.8* 1* 11.5* 1 11.5
tpd CLK QCC
L
= 15 pF 4.9* 11.2* 1* 13* 1 13 ns
QD
CL = 15 pF
5.3* 12.5* 1* 14.5* 1 14.5
ns
tPHL CLR Qn3.9* 8.1* 1* 9.5* 1 9.5
QA4.9 10.5 1 12 1 12
tpd
CLK
QB5.6 11.8 1 13.5 1 13.5
tpd CLK QCCL = 50 pF 6.2 13.2 1 15 1 15 ns
QD
CL = 50 pF
6.6 14.5 1 16.5 1 16.5
ns
tPHL CLR Qn5.2 10.1 1 11.5 1 11.5
* On products compliant to MIL-PRF-38535, this parameter is not production tested.
& & $'("%$ $#($ )(! $ # '("%1# (
#0$ )%# ' #1#+)"#$, %(%#( %% %$ #(
)#'%$ %(# #0$ 0%+, #-% $(!"#$ (##(1# # (0 
%$0# ( $$!# ## )(! .! $#,
& & $'("%$ $#($ )(! $ # '("%1# (
#0$ )%# ' #1#+)"#$, %(%#( %% %$ #(
)#'%$ %(# #0$ 0%+, #-% $(!"#$ (##(1# # (0 
%$0# ( $$!# ## )(! .! $#,
VOL p Owe! ompm, maxxmum dynamwc VOL VOL v Owe! ompm, mmmum dynamic VOL vOH v Owe! ompm, mmmum dynamic VQH VIH D VCC ‘4‘ TEXAS INSTRUMENTS
 
   
SCLS457D − FEBRUARY 2001 − REVISED APRIL 2005
7
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
noise characteristics, VCC = 3.3 V, CL = 50 pF, TA = 25°C (see Note 5)
PARAMETER
SN74LV393A
UNIT
PARAMETER
MIN TYP MAX
UNIT
VOL(P) Quiet output, maximum dynamic VOL 0.3 0.8 V
VOL(V) Quiet output, minimum dynamic VOL −0.2 −0.8 V
VOH(V) Quiet output, minimum dynamic VOH 2.8 V
VIH(D) High-level dynamic input voltage 2.31 V
VIL(D) Low-level dynamic input voltage 0.99 V
NOTE 5: Characteristics are for surface-mount packages only.
operating characteristics, TA = 25°C
PARAMETER TEST CONDITIONS VCC TYP UNIT
Cpd
Power dissipation capacitance
CL = 50 pF,
f = 10 MHz
3.3 V 15.2
pF
C
pd
Power dissipation capacitance
C
L
= 50 pF,
f = 10 MHz
5 V 17.3
pF
CL A CL (see Note A) A (see Note A) : Under Test w] LOAD CIRCUIT FOR 3-STATE AND OPEN-DRAIN OUTPUT Timing Input 7% i H7 tw 4H ‘ k—Hi I I H ‘ 777777 50% v o v VOLTAGE WAVEFORMS PULSE DURATION 7,7,,V I ' 50 Output npu 7‘! 9g ‘ o v Control \ IPLH H H—b‘r IPHL ‘ v Output ‘ 7 7 7 OH Waveform 1 mane: \ 50% Vcc 50% Vcc SI at Vcc p i VoL (see Note B) \ IPHL H H—Dti IPLH \ VOH Output cut-pI-Phase \ Wavetorm 2 Output k5” V00 2 50% V50 S1 at GND 7 7 7 VOL (see Note B) VOLTAGE WAVEFORMS PROPAGATION nELAv TIMES INVEHTING AND NONINVERTING OUTPUTS NOTES. A. CL rncIudes probe and no capacrtance. a. Wavelorm I rs tor an output wrth rnternaI condrtrons such that the output rs Wauetorm 2 rs Ior an output wrth rnternat condrtrons such that the output rs AII rnput puIses are SupplIed by generators havrng the IoIIowrng charactens The outputs are measured one at a tone, wrth one rnput transrtron oer rnea lpLZ and tpHZ are the same as tars. lPZL and tPZH are the same as ten tpHL and lpLH are the same as Ipd AII parameters and wavetorms are not aophcame to aH devrces, IQFWPO b TEXAS INSTRUMENTS 8 POST OFFICE on 655303 I DALLAS TEXAS 7528
 
   
SCLS457D − FEBRUARY 2001 − REVISED APRIL 2005
8POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
PARAMETER MEASUREMENT INFORMATION
50% VCC
VCC
VCC
0 V
0 V
th
tsu
VOLTAGE WAVEFORMS
SETUP AND HOLD TIMES
Data Input
tPLH
tPHL
tPHL
tPLH
VOH
VOH
VOL
VOL
VCC
0 V
50% VCC
50% VCC
Input
Out-of-Phase
Output
In-Phase
Output
Timing Input
50% VCC
VOLTAGE WAVEFORMS
PROPAGATION DELAY TIMES
INVERTING AND NONINVERTING OUTPUTS
Output
Control
Output
Waveform 1
S1 at VCC
(see Note B)
Output
Waveform 2
S1 at GND
(see Note B)
VOL
VOH
tPZL
tPZH
tPLZ
tPHZ
≈VCC
0 V
50% VCC VOL + 0.3 V
50% VCC ≈0 V
VCC
VOLTAGE WAVEFORMS
ENABLE AND DISABLE TIMES
LOW- AND HIGH-LEVEL ENABLING
tPLH/tPHL
tPLZ/tPZL
tPHZ/tPZH
Open Drain
Open
VCC
GND
VCC
TEST S1
VCC
0 V
50% VCC
tw
VOLTAGE WAVEFORMS
PULSE DURATION
Input
NOTES: A. CL includes probe and jig capacitance.
B. Waveform 1 is for an output with internal conditions such that the output is low, except when disabled by the output control.
Waveform 2 is for an output with internal conditions such that the output is high, except when disabled by the output control.
C. All input pulses are supplied by generators having the following characteristics: PRR ≤ 1 MHz, ZO = 50 Ω, tr ≤3 ns, tf ≤ 3 ns.
D. The outputs are measured one at a time, with one input transition per measurement.
E. tPLZ and tPHZ are the same as tdis.
F. tPZL and tPZH are the same as ten.
G. tPHL and tPLH are the same as tpd.
H. All parameters and waveforms are not applicable to all devices.
From Output
Under Test CL
(see Note A)
LOAD CIRCUIT FOR
3-STATE AND OPEN-DRAIN OUTPUTS
S1
V
CC
RL = 1 kΩ
GND
From Output
Under Test CL
(see Note A)
Test
Point
LOAD CIRCUIT FOR
TOTEM-POLE OUTPUTS
Open
50% VCC
50% VCC 50% VCC
50% VCC
50% VCC 50% VCC
50% VCC 50% VCC
VOH − 0.3 V
Figure 1. Load Circuit and Voltage Waveforms
TEXAS INSTRUMENTS Samples Samples Samples Samples Sample: Sample: Samples Samples
PACKAGE OPTION ADDENDUM
www.ti.com 13-Aug-2021
Addendum-Page 1
PACKAGING INFORMATION
Orderable Device Status
(1)
Package Type Package
Drawing Pins Package
Qty Eco Plan
(2)
Lead finish/
Ball material
(6)
MSL Peak Temp
(3)
Op Temp (°C) Device Marking
(4/5)
Samples
SN74LV393AD ACTIVE SOIC D 14 50 RoHS & Green NIPDAU Level-1-260C-UNLIM -40 to 85 LV393A
SN74LV393ADBR ACTIVE SSOP DB 14 2000 RoHS & Green NIPDAU Level-1-260C-UNLIM -40 to 85 LV393A
SN74LV393ADGVR ACTIVE TVSOP DGV 14 2000 RoHS & Green NIPDAU Level-1-260C-UNLIM -40 to 85 LV393A
SN74LV393ADR ACTIVE SOIC D 14 2500 RoHS & Green NIPDAU Level-1-260C-UNLIM -40 to 85 LV393A
SN74LV393ANSR ACTIVE SO NS 14 2000 RoHS & Green NIPDAU Level-1-260C-UNLIM -40 to 85 74LV393A
SN74LV393APW ACTIVE TSSOP PW 14 90 RoHS & Green NIPDAU Level-1-260C-UNLIM -40 to 85 LV393A
SN74LV393APWR ACTIVE TSSOP PW 14 2000 RoHS & Green NIPDAU Level-1-260C-UNLIM -40 to 85 LV393A
SN74LV393APWRG4 ACTIVE TSSOP PW 14 2000 RoHS & Green NIPDAU Level-1-260C-UNLIM -40 to 85 LV393A
(1) The marketing status values are defined as follows:
ACTIVE: Product device recommended for new designs.
LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design.
PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
OBSOLETE: TI has discontinued the production of the device.
(2) RoHS: TI defines "RoHS" to mean semiconductor products that are compliant with the current EU RoHS requirements for all 10 RoHS substances, including the requirement that RoHS substance
do not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, "RoHS" products are suitable for use in specified lead-free processes. TI may
reference these types of products as "Pb-Free".
RoHS Exempt: TI defines "RoHS Exempt" to mean products that contain lead but are compliant with EU RoHS pursuant to a specific EU RoHS exemption.
Green: TI defines "Green" to mean the content of Chlorine (Cl) and Bromine (Br) based flame retardants meet JS709B low halogen requirements of <=1000ppm threshold. Antimony trioxide based
flame retardants must also meet the <=1000ppm threshold requirement.
(3) MSL, Peak Temp. - The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature.
(4) There may be additional marking, which relates to the logo, the lot trace code information, or the environmental category on the device.
(5) Multiple Device Markings will be inside parentheses. Only one Device Marking contained in parentheses and separated by a "~" will appear on a device. If a line is indented then it is a continuation
of the previous line and the two combined represent the entire Device Marking for that device.
I TEXAS INSTRUMENTS
PACKAGE OPTION ADDENDUM
www.ti.com 13-Aug-2021
Addendum-Page 2
(6) Lead finish/Ball material - Orderable Devices may have multiple material finish options. Finish options are separated by a vertical ruled line. Lead finish/Ball material values may wrap to two
lines if the finish value exceeds the maximum column width.
Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information
provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and
continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals.
TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release.
In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis.
OTHER QUALIFIED VERSIONS OF SN74LV393A :
•Automotive : SN74LV393A-Q1
•Enhanced Product : SN74LV393A-EP
NOTE: Qualified Version Definitions:
•Automotive - Q100 devices qualified for high-reliability automotive applications targeting zero defects
•Enhanced Product - Supports Defense, Aerospace and Medical Applications
l TEXAS INSTRUMENTS REEL DIMENSIONS TAPE DIMENSIONS 7 “KO '«Pt» Reel Diameter AD Dimension designed to accommodate the component Width ED Dimension designed to accommodate the component tengtn K0 Dimension designed to accommodate the component thickness 7 W OveraH wtdlh loe earner tape i P1 Pitch between SucCeSSWe cavtty centers f T Reel Width (W1) QUADRANT ASSIGNMENTS FOR PIN 1 ORIENTATION IN TAPE O O O D O O D D SprocketHotes ,,,,,,,,,,, ‘ User Direcllon 0' Feed Pockel Quadrams
TAPE AND REEL INFORMATION
*All dimensions are nominal
Device Package
Type Package
Drawing Pins SPQ Reel
Diameter
(mm)
Reel
Width
W1 (mm)
A0
(mm) B0
(mm) K0
(mm) P1
(mm) W
(mm) Pin1
Quadrant
SN74LV393ADBR SSOP DB 14 2000 330.0 16.4 8.35 6.6 2.4 12.0 16.0 Q1
SN74LV393ADGVR TVSOP DGV 14 2000 330.0 12.4 6.8 4.0 1.6 8.0 12.0 Q1
SN74LV393ADR SOIC D 14 2500 330.0 16.4 6.5 9.0 2.1 8.0 16.0 Q1
SN74LV393ANSR SO NS 14 2000 330.0 16.4 8.2 10.5 2.5 12.0 16.0 Q1
SN74LV393APWR TSSOP PW 14 2000 330.0 12.4 6.9 5.6 1.6 8.0 12.0 Q1
PACKAGE MATERIALS INFORMATION
www.ti.com 19-Jun-2021
Pack Materials-Page 1
l TEXAS INSTRUMENTS TAPE AND REEL BOX DIMENSIONS
*All dimensions are nominal
Device Package Type Package Drawing Pins SPQ Length (mm) Width (mm) Height (mm)
SN74LV393ADBR SSOP DB 14 2000 853.0 449.0 35.0
SN74LV393ADGVR TVSOP DGV 14 2000 853.0 449.0 35.0
SN74LV393ADR SOIC D 14 2500 853.0 449.0 35.0
SN74LV393ANSR SO NS 14 2000 853.0 449.0 35.0
SN74LV393APWR TSSOP PW 14 2000 853.0 449.0 35.0
PACKAGE MATERIALS INFORMATION
www.ti.com 19-Jun-2021
Pack Materials-Page 2
17 i Gage Plane 0,15 7|,20MAX 0,? PINS N 14 1s 20 24 as 43 56 DIM AMAX 3‘70 3.70 5‘10 5.10 700 9,00 11,40 AMIN 350 3,50 400 4,90 7‘70 9,50 11,20 407325| /E 03/00 *5 TEXAS INSTRUMENTS p057 omca aox $55303 - DALLAS IEXAS 752s5
MECHANICAL DATA
MPDS006C – FEBRUARY 1996 – REVISED AUGUST 2000
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
DGV (R-PDSO-G**) PLASTIC SMALL-OUTLINE
24 PINS SHOWN
14
3,70
3,50 4,90
5,10
20
DIM
PINS **
4073251/E 08/00
1,20 MAX
Seating Plane
0,05
0,15
0,25
0,50
0,75
0,23
0,13
112
24 13
4,30
4,50
0,16 NOM
Gage Plane
A
7,90
7,70
382416
4,90
5,103,70
3,50
A MAX
A MIN
6,60
6,20
11,20
11,40
56
9,60
9,80
48
0,08
M
0,07
0,40
0°–8°
NOTES: A. All linear dimensions are in millimeters.
B. This drawing is subject to change without notice.
C. Body dimensions do not include mold flash or protrusion, not to exceed 0,15 per side.
D. Falls within JEDEC: 24/48 Pins – MO-153
14/16/20/56 Pins – MO-194
MECHANICAL DATA D U1 4)} 0 (3'4) DLASHC SMALL 0U ¥N¥ 4040047 5/M 06/1‘ NO'ES, A AH Hnec' dimensmrs c'e m 'mc'ves ['nflhmeter5> B Th5 drawer ‘5 subje», ,0 change mm: Home, A Body \cngth docs rm mac mod Hoar, p'omswons, (xv gmc bms Mom mm warmers, or gm buns sha‘ nm exceed 3005 (015) eam swce @ Body mm does 101 meme 11mm fish. E Rdererce JEDEC MS 012 mam AB, nter‘ec: flash sfu‘ not exceed 0017 (043) each swde {If TEXAS INSTRUMENTS www.1i.com
LAND PATTERN DATA D (R7PDSOmGl4) PLASTlC SMALL OUTLINE Example Board Layout Sterlazlogpeulyngs (Mole c) —— <—14x0,55 -hhheb&&t="" tmedddifi§n%="" 5.40="" 5,40="" @eeeeeej="" rfihfl§eflhj="" —=""> ——l 2x1,27 Example Non Soldermask Delined Pad Example Pad Geometry (See Note c) F Example l / Solder Mask Opening 7 0 07 f (See Note E) All Armlnd ,/ tzllmss/E oa/lz NOTES: A. All linear dimensions are in millimeters. a, Tnis drawan is subject to cnonae wl'lhuul notice. c. Publlcutl’on chs7351 is recommended tor alternate desl’gns. D. Laser ctming apertures w‘lth trapezoidal walls and also roundlng comers wlll otter better paste release. Customers should contact their board assembly site for stencil design recommendations, Reter tc ch—7525 lor otner stencil recommendations. E. Customers snoola contact their ooard looricotion site lor solder musk tolerances between ond oroond signol oods. {I} Tums INSTRUMENTS www.li.com
MECHANICAL DATA "7’7 : 3‘ AST‘C SMAH CJ’ N7 HHHHHHH . . ‘7,4’ 44*, A f;—‘ NO'ES' A AH Hnec' dimensmrs c'e m m'\\me(ers Dwmens'amnq cnd tu‘erc'vcmg per ASME w 5M 1994, Tm drawer ‘5 subje», ,o "hangs wnrau: Home, Budy \evvgih ‘ues m W" Le mom Hush, pyuws‘m Ur guts Ms M exceed 0,15 each m & Rudy wde does NM Wands \Mer end flair \Mefiead 'Wclsh shaH um exceed 0‘75 each S‘de E Fa‘s WM" JEDEC M07153 MUM "\u>h, main: bus, 01 guie buns shuH {if TEXAS INSTRUMENTS www.ci.com
PW (RiPDsoicM) LAND PATTERN DATA PLASTHC SMALL OUTLINE Example Board Layout (Male 0) —>| ‘,——12x0 65 HHHHHHHi 5,60 HHHHHHHHi l“ l l l Example Non So‘dermask Defined Pad 4 x 1,60 / H l <—0,07 y/="" ah="" around="" pad="" seamelry="" (see="" nale="" c)="" solder="" mask="" opening="" (see="" note="" e)="" stencil="" 0="" en'ln="" s="" (notepd)="" ‘3="" 14x0="" 30="" h="" '«,lzxo="" 65="" ~hhhhhh~="" 5,60="" hhhhhhh—="" example="" example="" 421128472/6="" 08/15="" notes:="" ah="" h‘lneor="" dimensions="" one="" in="" rnihll'rneters.="" tn‘ls="" dvowing="" is="" subject="" lp="" change="" wltnoul="" nallee.="" publl'cotlon="" hpcjssh="" is="" recommended="" lar="" allemale="" deslgns.="" laser="" cutllng="" apertures="" wch="" tropexoidm="" walls="" and="" also="" raund‘lna="" comers="" wlll="" we!="" better="" pasle="" release="" customers="" show="" contact="" their="" board="" assembly="" sl’te="" (ov="" stenci‘="" design="" recommendations.="" reler="" to="" ”50—7525="" lur="" other="" stencl‘="" recommendotluns="" customers="" shou‘d="" contact="" their="" board="" hoercot'lon="" shte="" (or="" solder="" musk="" tolerances="" between="" and="" around="" s'lgnol="" pods.="" *1?="" tums="" instruments="" www.ti.com="">
oo A‘ioyi 55 fiHHHHHHHHHHHHfi {'3 TEXAS INSTRUMENTS
MECHANICAL DATA
MSSO002E – JANUARY 1995 – REVISED DECEMBER 2001
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
DB (R-PDSO-G**) PLASTIC SMALL-OUTLINE
4040065 /E 12/01
28 PINS SHOWN
Gage Plane
8,20
7,40
0,55
0,95
0,25
38
12,90
12,30
28
10,50
24
8,50
Seating Plane
9,907,90
30
10,50
9,90
0,38
5,60
5,00
15
0,22
14
A
28
1
2016
6,50
6,50
14
0,05 MIN
5,905,90
DIM
A MAX
A MIN
PINS **
2,00 MAX
6,90
7,50
0,65 M
0,15
0°–ā8°
0,10
0,09
0,25
NOTES: A. All linear dimensions are in millimeters.
B. This drawing is subject to change without notice.
C. Body dimensions do not include mold flash or protrusion not to exceed 0,15.
D. Falls within JEDEC MO-150
MECHANICAL DATA NS (R-PDSO-G") PLASTIC SMALL—OUTLINE PACKAGE 14-PINS SHOWN HHFHHFH j j t t H H j, A jfi/—\ % lgLLLLLiLLL/fiif A MAX 1060 1060 1290 1530 A MW 990 9,90 1230 14‘70 4040062/0 03/03 VOTES: A. AH Hneur dimenswons are m mHHmetevs a, Tm: druwmg 5 subject to change wmom name. 0 Body dwmenswons do not mamas mom flash 0v pmtmswom not to exceed 0,15 INSTRUMEN'IS www.li.m
IMPORTANT NOTICE AND DISCLAIMER
TI PROVIDES TECHNICAL AND RELIABILITY DATA (INCLUDING DATASHEETS), DESIGN RESOURCES (INCLUDING REFERENCE
DESIGNS), APPLICATION OR OTHER DESIGN ADVICE, WEB TOOLS, SAFETY INFORMATION, AND OTHER RESOURCES “AS IS”
AND WITH ALL FAULTS, AND DISCLAIMS ALL WARRANTIES, EXPRESS AND IMPLIED, INCLUDING WITHOUT LIMITATION ANY
IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE OR NON-INFRINGEMENT OF THIRD
PARTY INTELLECTUAL PROPERTY RIGHTS.
These resources are intended for skilled developers designing with TI products. You are solely responsible for (1) selecting the appropriate
TI products for your application, (2) designing, validating and testing your application, and (3) ensuring your application meets applicable
standards, and any other safety, security, or other requirements. These resources are subject to change without notice. TI grants you
permission to use these resources only for development of an application that uses the TI products described in the resource. Other
reproduction and display of these resources is prohibited. No license is granted to any other TI intellectual property right or to any third party
intellectual property right. TI disclaims responsibility for, and you will fully indemnify TI and its representatives against, any claims, damages,
costs, losses, and liabilities arising out of your use of these resources.
TI’s products are provided subject to TI’s Terms of Sale (https:www.ti.com/legal/termsofsale.html) or other applicable terms available either
on ti.com or provided in conjunction with such TI products. TI’s provision of these resources does not expand or otherwise alter TI’s
applicable warranties or warranty disclaimers for TI products.IMPORTANT NOTICE
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2021, Texas Instruments Incorporated