Lattice Semiconductor Corporation 的 iCE40 UltraLite Family 规格书

规格书反馈/错误

:.'.' LATTICE ll. SEMICONDUCTOR.

iCE40 UltraLite™ Family Data Sheet

DS1050 Version 1.4, November 2016

_.'_.'_.' LATTICE CCCCCCCCCCCCC

www.latticesemi.com 1-1 DS1050 Introduction_01.2

July 2016 Data Sheet DS1050

or product names are trademarks or registered trademarks of their respective holders. The specifications and information herein are subject to change without notice.

General Description

iCE40 UltraLite family is an optimum logic, smallest footprint, low I/O count ultra-low power FPGA and sensor man-

ager with instant on capability. It is designed for ultra-low power mobile applications, such as smartphones, tablets

and hand-held devices. The iCE40 UltraLite family includes integrated blocks to interface with virtually all mobile

sensors and application processors. The iCE40 UltraLite family also features two on-chip oscillators, 10 kHz and 48

MHz. The LFOSC (10 kHz) is ideal for low power function in always-on applications, while HFOSC (48 MHz) can be

used for awaken activities.

The hardened RGB PWM IP, with the three 24 mA constant current RGB LED outputs on the iCE40 UltraLite pro-

vides all the necessary logic to directly drive the service LED, without the need of external MOSFET or buffer.

The 400 mA constant current IR driver output provides a direct interface to external LED for application such as

IrDA functions. Users simply implement the hardened TX/RX pulse logic that meets their needs, and connect the IR

driver directly to the LED, without the need of external MOSFET or buffer. The 100 mA Barcode Emulation driver

output provides a direct interface for applications such as barcode scanning. The 100 mA and 400 mA drivers can

also be combined to be used as a 500 mA IR driver if higher than 400 mA current drive is required.

The iCE40 UltraLite family of devices are targeting for mobile applications to perform functions such as IrDA, Ser-

vice LED, Barcode Emulation, GPIO Expander, SDIO Level Shift, and other custom functions.

The iCE40 UltraLite family features two device densities of 640 or 1K Look Up Tables (LUTs) of logic with program-

mable I/Os that can be used as an interface port or general purpose I/O. It also has up to 56 kbits of Block RAMs to

work with user logic.

iCE40 UltraLite Family Data Sheet

Introduction

Features

Flexible Logic Architecture

• Two devices with 640 or 1K LUTs

• Offered in 16-ball WLCSP package

• Offered in 36-ball ucBGA package

Ultra-low Power Devices

• Advanced 40 nm ultra-low power process

• Typical 35 µA standby current which equals

42 uW standby power consumption

Embedded and Distributed Memory

• Up to 56 kbits sysMEM™ Embedded Block RAM

Two Hardened Interfaces

• Two optional FIFO mode I2C interface up to

1 MHz

• Either master or slave

Two On-Chip Oscillators

• Low Frequency Oscillator - 10 kHz

• High Frequency Oscillator - 48 MHz

Hardened PWM circuit for RGB

Hardened TX/RX Pulse Logic circuit for IR

LED

24 mA Current Drive RGB LED Outputs

• Three drive outputs in each device

• User selectable sink current up to 24 mA

400 or 500 mA Current Drive IR LED Output

• One IR drive output in each device

• User selectable sink current up to 400 mA

• Can be combined with 100 mA Barcode driver to

form 500 mA IR driver

100 mA Current Drive Barcode Emulator

• One barcode driver output in each device

• User selectable sink current up to 100 mA

• Can be combined with 400 mA IR driver to use

as 500 mA IR driver

Flexible On-Chip Clocking

• Eight low skew global signal resource, six can

be directly driven from external pins

• One PLL with dynamic interface per device

_:_:_: LATTICE 55555555555555

1-2

Introduction

iCE40 UltraLite Family Data Sheet

Flexible Device Configuration

• SRAM is configured through:

— Standard SPI Interface

— Internal Nonvolatile Configuration Memory

(NVCM)

Ultra-Small Form Factor

• As small as 1.409 mm x 1.409 mm

Applications

• Smartphones

• Tablets and Consumer Handheld Devices

• Handheld Industrial Devices

• Multi Sensor Management Applications

• IR remote, Barcode emulator

• RGB light control

Table 1-1. iCE40 UltraLite Family Selection Guide

Introduction

The iCE40 UltraLite devices are fabricated on a 40 nm CMOS low power process. The device architecture has sev-

eral features such as user configurable RGB LED and IR LED Controllers, and two Oscillators.

The iCE40 UltraLite FPGAs are available in very small form factor packages, as small as 1.409 mm x 1.409 mm.

The small form factor allows the device to easily fit into a lot of mobile applications. Table 1-1 shows the LUT densi-

ties, package and I/O pin count.

The iCE40 UltraLite devices offer I/O features such as programmable multiple value pull-up resistors. Pull-up fea-

tures are controllable on a “per-pin” basis.

The iCE40 UltraLite devices also provide flexible, reliable and secure configuration from on-chip NVCM. These

devices can also configure themselves from external SPI Flash, or be configured by an external master such as a

CPU.

Lattice provides a variety of design tools that allow complex designs to be efficiently implemented using the iCE40

UltraLite family of devices. Popular logic synthesis tools provide synthesis library support for iCE40 UltraLite. Lat-

tice design tools use the synthesis tool output along with the user-specified preferences and constraints to place

and route the design in the iCE40 UltraLite device. These tools extract the timing from the routing and back-anno-

tate it into the design for timing verification.

Part Number iCE40UL-640 iCE40UL-1K

Logic Cells (LUT + Flip-Flop) 640 1248

EBR Memory Blocks 14 14

EBR Memory Bits 56 k 56 k

PLL Block111

Hardened I2C 2 2

Hardened IR TX/RX 1 1

Hardened RGB PWM IP 1 1

HF Oscillator (48 MHz) 1 1

LF Oscillator (10 kHz) 1 1

24 mA LED Sink 3 3

100 mA LED Sink 1 1

400 mA LED Sink 1 1

Packages, ball pitch, dimension Programmable I/O Count

16-ball WLCSP, 0.35 mm, 1.409 mm x 1.409 mm 10 10

36-ball ucBGA, 0.40 mm, 2.5 mm x 2.5 mm 26 26

1. Only in 36-ball ucBGA package.

_:,-_: LATTICE 55555555555555

1-3

Introduction

iCE40 UltraLite Family Data Sheet

Lattice provides many pre-engineered IP (Intellectual Property) modules, including a number of reference designs,

licensed free of charge, optimized for the iCE40 UltraLite FPGA family. Lattice also can provide fully verified bit-

stream for some of the widely used target functions in mobile device applications, such as IR remote, barcode emu-

lator, and RGB LED control functions. Users can use these functions as offered by Lattice, or they can use the

design to create their own unique required functions. For more information regarding Lattice's reference designs or

fully-verified bitstreams, please contact your local Lattice representative.

' 'LATTICE .sEMICoNDUCTaR. IR and arcade Drv C] IIO Bank 0 canh, IIO Bank 1 . . IIO Bank 2

www.latticesemi.com 2-1 DS1050 Architecture_01.2

July 2016 Data Sheet DS1050

or product names are trademarks or registered trademarks of their respective holders. The specifications and information herein are subject to change without notice.

Architecture Overview

The iCE40 UltraLite family architecture contains an array of Programmable Logic Blocks (PLB), two Oscillator Gen-

erators, two user configurable I2C controllers, and blocks of sysMEM™ Embedded Block RAM (EBR) surrounded

by Programmable I/O (PIO). Figure 2-1shows the block diagram of the iCE40UL-1K device.

Figure 2-1. iCE40UL-1K Device, Top View

The logic blocks, Programmable Logic Blocks (PLB) and sysMEM EBR blocks, are arranged in a two-dimensional

grid with rows and columns. Each column has either PLB or EBR blocks. The PIO cells are located at the top and

bottom of the device, arranged in banks. The PLB contains the building blocks for logic, arithmetic, and register

functions. The PIOs utilize a flexible I/O buffer referred to as a sysIO buffer that supports operation with a variety of

interface standards. The blocks are connected with many vertical and horizontal routing channel resources. The

place and route software tool automatically allocates these routing resources.

In the iCE40 UltraLite family, there are three sysIO banks, one on top and two at the bottom. User can connect all

VCCIOs together, if all the I/Os are using the same voltage standard. Refer to the details in later sections of this doc-

ument. The sysMEM EBRs are large 4 kbit, dedicated fast memory blocks. These blocks can be configured as

RAM, ROM or FIFO with user logic using PLBs.

The iCE40 UltraLite also includes two user I2C ports, two Oscillators, and high current RGB and IR LED sinks, and

a 100 mA Barcode emulation output.

4 4 kbit RAM

3 4 kbit RAM

PLB

I/O Bank 0

I/O Bank 2

HFOSC LFOSC

config

I/O Bank 1

NVCM

IR and

Barcode Drv

RGB

Drv

Flip-flop with Enable

and Reset Controls

Carry Logic

4-Input Look-up

Table (LUT)

8 Logic Cells = Programmable Logic Block

iCE40 UltraLite Family Data Sheet

Architecture

ﬂ: LATTICE Illssumomzucrok

2-2

Architecture

iCE40 UltraLite Family Data Sheet

PLB Blocks

The core of the iCE40 UltraLite device consists of Programmable Logic Blocks (PLB) which can be programmed to

perform logic and arithmetic functions. Each PLB consists of eight interconnected Logic Cells (LC) as shown in

Figure 2-2. Each LC contains one LUT and one register.

Figure 2-2. PLB Block Diagram

Logic Cells

Each Logic Cell includes three primary logic elements shown in Figure 2-2.

• A four-input Look-Up Table (LUT) builds any combinational logic function, of any complexity, requiring up to

four inputs. Similarly, the LUT element behaves as a 16x1 Read-Only Memory (ROM). Combine and cascade

multiple LUTs to create wider logic functions.

• A ‘D’-style Flip-Flop (DFF), with an optional clock-enable and reset control input, builds sequential logic func-

tions. Each DFF also connects to a global reset signal that is automatically asserted immediately following

device configuration.

• Carry Logic boosts the logic efficiency and performance of arithmetic functions, including adders, subtracters,

comparators, binary counters and some wide, cascaded logic functions.

Table 2-1. Logic Cell Signal Descriptions

Function Type Signal Names Description

Input Data signal I0, I1, I2, I3 Inputs to LUT

Input Control signal Enable Clock enable shared by all LCs in the PLB

Input Control signal Set/Reset1 Asynchronous or synchronous local set/reset shared by all LCs in

the PLB.

Input Control signal Clock Clock one of the eight Global Buffers, or from the general-purpose

interconnects fabric shared by all LCs in the PLB

Input Inter-PLB signal FCIN Fast carry in

Output Data signals O LUT or registered output

Output Inter-PFU signal FCOUT Fast carry out

1. If Set/Reset is not used, then the flip-flop is never set/reset, except when cleared immediately after configuration.

= Statically defined by configuration program

LUT

Carry Logic

Logic Cell

DFF

Flip-flop with

optional enable and

set or reset controls

Four-input

Look-Up Table

(LUT)

Clock

Enable

FCOUT

FCIN

Set/Reset

Shared Block-Level Controls

Programmable Logic

Block (PLB)

8 Logic Cells (LCs)

_:,-_: LATTICE 55555555555555

2-3

Architecture

iCE40 UltraLite Family Data Sheet

Routing

There are many resources provided in the iCE40 UltraLite devices to route signals individually with related control

signals. The routing resources consist of switching circuitry, buffers and metal interconnect (routing) segments.

The inter-PLB connections are made with three different types of routing resources: Adjacent (spans two PLBs), x4

(spans five PLBs) and x12 (spans thirteen PLBs). The Adjacent, x4 and x12 connections provide fast and efficient

connections in the diagonal, horizontal and vertical directions.

The design tool takes the output of the synthesis tool and places and routes the design.

Clock/Control Distribution Network

Each iCE40 UltraLite device has six global inputs, two pins on the top bank and four pins on the bottom bank

These global inputs can be used as high fanout nets, clock, reset or enable signals. The dedicated global pins are

identified as Gxx and each drives one of the eight global buffers. The global buffers are identified as GBUF[7:0].

These six inputs may be used as general purpose I/O if they are not used to drive the clock nets.

Table 2-2 lists the connections between a specific global buffer and the inputs on a PLB. All global buffers optionally

connect to the PLB CLK input. Any four of the eight global buffers can drive logic inputs to a PLB. Even-numbered

global buffers optionally drive the Set/Reset input to a PLB. Similarly, odd-numbered buffers optionally drive the

PLB clock-enable input. GBUF[7:6, 3:0] can connect directly to G[7:6, 3:0] pins respectively. GBUF4 and GBUF5

can connect to the two on-chip Oscillator Generators (GBUF4 connects to LFOSC, GBUF5 connects to HFOSC).

Table 2-2. Global Buffer (GBUF) Connections to Programmable Logic Blocks

The maximum frequency for the global buffers are shown in the iCE40 UltraLite External Switching Characteristics

tables later in this document.

Global Hi-Z Control

The global high-impedance control signal, GHIZ, connects to all I/O pins on the iCE40 UltraLite device. This GHIZ

signal is automatically asserted throughout the configuration process, forcing all user I/O pins into their high-imped-

ance state.

Global Reset Control

The global reset control signal connects to all PLB and PIO flip-flops on the iCE40 UltraLite device. The global

reset signal is automatically asserted throughout the configuration process, forcing all flip-flops to their defined

wake-up state. For PLB flip-flops, the wake-up state is always reset, regardless of the PLB flip-flop primitive used in

the application.

Global Buffer LUT Inputs Clock Reset Clock Enable

GBUF0

Yes, any 4 of 8

GBUF Inputs

Ye s Ye s

GBUF1 Yes Yes

GBUF2 Yes Yes

GBUF3 Yes Yes

GBUF4 Yes Yes

GBUF5 Yes Yes

GBUF6 Yes Yes

GBUF7 Yes Yes

ﬂ: LATTICE .- lsstoNnucrap 4. EVPASS LL PLL AL

2-4

Architecture

iCE40 UltraLite Family Data Sheet

sysCLOCK Phase Locked Loops (PLLs) (sysCLOCK PLL is only supported in 36-ball ucBGA package)

The sysCLOCK PLLs provide the ability to synthesize clock frequencies. The iCE40 UltraLite devices have one

sysCLOCK PLL. REFERENCECLK is the reference frequency input to the PLL and its source can come from an

external I/O pin, the internal Oscillator Generators from internal routing. EXTFEEDBACK is the feedback signal to

the PLL which can come from internal routing or an external I/O pin. The feedback divider is used to multiply the

reference frequency and thus synthesize a higher frequency clock output.

The PLLOUT output has an output divider, thus allowing the PLL to generate different frequencies for each output.

The output divider can have a value from 1 to 64 (in increments of 2X). The PLLOUT outputs can all be used to

drive the iCE40 UltraLite global clock network directly or general purpose routing resources can be used.

The LOCK signal is asserted when the PLL determines it has achieved lock and de-asserted if a loss of lock is

detected. A block diagram of the PLL is shown in Figure 2-3.

The timing of the device registers can be optimized by programming a phase shift into the PLLOUT output clock

which will advance or delay the output clock with reference to the REFERENCECLK clock. This phase shift can be

either programmed during configuration or can be adjusted dynamically. In dynamic mode, the PLL may lose lock

after a phase adjustment on the output used as the feedback source and not relock until the tLOCK parameter has

been satisfied.

There is an additional feature in the iCE40 UltraLite PLL. There are 2 FPGA controlled inputs, SCLK and SDI, that

allows the user logic to serially shift in data thru SDI, clocked by SCLK clock. The data shifted in would change the

configuration settings of the PLL. This feature allows the PLL to be time multiplexed for different functions, with dif-

ferent clock rates. After the data is shifted in, user would simply pulse the RESET input of the PLL block, and the

PLL will re-lock with the new settings. For more details, please refer to TN1251, iCE40 sysCLOCK PLL Design and

Usage Guide.

Figure 2-3. PLL Diagram

Table 2-3 provides signal descriptions of the PLL block.

Input

Divider

DIVR

Low-Pass

Filter

Voltage

Controlled

Oscillator

(VCO)

VCO

Divider

DIVQ

Feedback

Divider

DIVF

RANGE

Phase

Detector

Feedback_Path

Fine Delay

Adjustment

Feedback

Phase

Shifter

LATCHINPUTVALUE

REFERENCECLK

DYNAMICDELAY[7:0]

BYPASS

RESET

EXTFEEDBACK

PLLOUTCORE

PLLOUTGLOBAL

LOCK

BYPASS

Low Power mode

SIMPLE

EXTERNAL

VCCPLL

GNDPLL

Fine Delay

Adjustment

Output Port

SCLK

SDI

_:_:_: LATTICE 55555555555555

2-5

Architecture

iCE40 UltraLite Family Data Sheet

Table 2-3. PLL Signal Descriptions

sysMEM Embedded Block RAM Memory

Larger iCE40 UltraLite device includes multiple high-speed synchronous sysMEM Embedded Block RAMs (EBRs),

each 4 kbit in size. This memory can be used for a wide variety of purposes including data buffering, and FIFO.

sysMEM Memory Block

The sysMEM block can implement single port, pseudo dual port, or FIFO memories with programmable logic

resources. Each block can be used in a variety of depths and widths as shown in Table 2-4.

Signal Name Direction Description

REFERENCECLK Input Input reference clock

BYPASS Input The BYPASS control selects which clock signal connects to the PLL-

OUT output.

0 = PLL generated signal

1 = REFERENCECLK

EXTFEEDBACK Input External feedback input to PLL. Enabled when the FEEDBACK_PATH

attribute is set to EXTERNAL.

DYNAMICDELAY[7:0] Input Fine delay adjustment control inputs. Enabled when

DELAY_ADJUSTMENT_MODE is set to DYNAMIC.

LATCHINPUTVALUE Input When enabled, puts the PLL into low-power mode; PLL output is held

static at the last input clock value. Set ENABLE ICEGATE_PORTA and

PORTB to ‘1’ to enable.

PLLOUTGLOBAL Output Output from the Phase-Locked Loop (PLL). Drives a global clock net-

work on the FPGA. The port has optimal connections to global clock

buffers GBUF4 and GBUF5.

PLLOUTCORE Output Output clock generated by the PLL, drives regular FPGA routing. The

frequency generated on this output is the same as the frequency of the

clock signal generated on the PLLOUTLGOBAL port.

LOCK Output When High, indicates that the PLL output is phase aligned or locked to

the input reference clock.

RESET Input Active low reset.

SCLK Input Input, Serial Clock used for re-programming PLL settings.

SDI Input Input, Serial Data used for re-programming PLL settings.

_:,-_: LATTICE 55555555555555

2-6

Architecture

iCE40 UltraLite Family Data Sheet

Table 2-4. sysMEM Block Configurations1

Block RAM

Configuration

Block RAM

Configuration

and Size

WADDR Port

Size (Bits)

WDATA Port

Size (Bits)

RADDR Port

Size (Bits)

RDATA Port

Size (Bits)

MASK Port

Size (Bits)

SB_RAM256x16

SB_RAM256x16NR

SB_RAM256x16NW

SB_RAM256x16NRNW

256x16 (4K) 8 [7:0] 16 [15:0] 8 [7:0] 16 [15:0] 16 [15:0]

SB_RAM512x8

SB_RAM512x8NR

SB_RAM512x8NW

SB_RAM512x8NRNW

512x8 (4K) 9 [8:0] 8 [7:0] 9 [8:0] 8 [7:0] No Mask Port

SB_RAM1024x4

SB_RAM1024x4NR

SB_RAM1024x4NW

SB_RAM1024x4NRNW

1024x4 (4K) 10 [9:0] 4 [3:0] 10 [9:0] 4 [3:0] No Mask Port

SB_RAM2048x2

SB_RAM2048x2NR

SB_RAM2048x2NW

SB_RAM2048x2NRNW

2048x2 (4K) 11 [10:0] 2 [1:0] 11 [10:0] 2 [1:0] No Mask Port

1. For iCE40 Ultra, the primitive name without "Nxx" uses rising-edge Read and Write clocks. "NR" uses rising-edge Write clock and falling-

edge Read clock. "NW" uses falling-edge Write clock and rising-edge Read clock. "NRNW" uses falling-edge clocks on both Read and

Write.

ﬂ: LATTICE .- lsstoNnucrap r—’%r—% —>—> —> —,‘—

2-7

Architecture

iCE40 UltraLite Family Data Sheet

RAM Initialization and ROM Operation

If desired, the contents of the RAM can be pre-loaded during device configuration.

By preloading the RAM block during the chip configuration cycle and disabling the write controls, the sysMEM block

can also be utilized as a ROM.

Memory Cascading

Larger and deeper blocks of RAM can be created using multiple EBR sysMEM Blocks.

RAM4k Block

Figure 2-4 shows the 256x16 memory configurations and their input/output names. In all the sysMEM RAM modes,

the input data and addresses for the ports are registered at the input of the memory array.

Figure 2-4. sysMEM Memory Primitives

Table 2-5. EBR Signal Descriptions

For further information on the sysMEM EBR block, please refer to TN1250, Memory Usage Guide for iCE40

Devices.

Signal Name Direction Description

WDATA[15:0] Input Write Data input.

MASK[15:0] Input

Masks write operations for individual data bit-lines.

0 = write bit

1 = do not write bit

WADDR[7:0] Input Write Address input. Selects one of 256 possible RAM locations.

WE Input Write Enable input.

WCLKE Input Write Clock Enable input.

WCLK Input Write Clock input. Default rising-edge, but with falling-edge option.

RDATA[15:0] Output Read Data output.

RADDR[7:0] Input Read Address input. Selects one of 256 possible RAM locations.

RE Input Read Enable input.

RCLKE Input Read Clock Enable input.

RCLK Input Read Clock input. Default rising-edge, but with falling-edge option.

WCLK

WERE

WCLKE RCLKE

RCLK

WDATA[15:0] RDATA[15:0]

MASK[15:0]

WADDR[7:0] RADDR[7:0]

Write Port Read Port

RAM4K

RAM Block

(256x16)

_:,-_: LATTICE ssssssssssssss _/0 Bank 0 ;l— . I/O Bank 2 IIO Bank1

2-8

Architecture

iCE40 UltraLite Family Data Sheet

sysIO Buffer Banks

iCE40 UltraLite devices have up to three I/O banks with independent VCCIO rails. The configuration SPI interface

signals are powered by SPI_VCCIO1. On the 16 WLCSP package, VCCIO1 and VPP_2V5 are connected to the same

pin on the package, and must meet the voltage requirement of both supplies. Please refer to the Pin Information

Summary table.

Programmable I/O (PIO)

The programmable logic associated with an I/O is called a PIO. The individual PIOs are connected to their respec-

tive sysIO buffers and pads. The PIOs are placed on the top and bottom of the devices.

Figure 2-5. I/O Bank and Programmable I/O Cell

The PIO contains three blocks: an input register block, output register block iCEGate™ and tri-state register block.

To save power, the optional iCEGate latch can selectively freeze the state of individual, non-registered inputs within

an I/O bank. Note that the freeze signal is common to the bank. These blocks can operate in a variety of modes

along with the necessary clock and selection logic.

Input Register Block

The input register blocks for the PIOs on all edges contain registers that can be used to condition high-speed inter-

face signals before they are passed to the device core.

Output Register Block

The output register block can optionally register signals from the core of the device before they are passed to the

sysIO buffers.

Figure 2-6 shows the input/output register block for the PIOs.

OUT

CCIO

I/O Bank 0 or 2

Voltage Supply

0 = Hi-Z

1 = Output

Enabled

PAD

iCEGATE

HOLD

Disabled ‘0’

OUTCLK

INCLK

Enabled ‘1’

Latch inhibits

switching for

power saving

Pull-up

Enable

Programmable

Pull-up

Gxx pins optionally

connect directly to

an associated

GBUF global

buffer

LPSG

4 4 kbit RAM

3 4 kbit RAM

PLB

I/O Bank 0

I/O Bank 2

HFOSC LFOSC

config

I/O Bank 1

NVCM

RGB

Drv

PIO

I2C

IR and

Barcode Drv

ﬂ: LATTICE lllllllllllllllll m 3?

2-9

Architecture

iCE40 UltraLite Family Data Sheet

Figure 2-6. iCE I/O Register Block Diagram

Table 2-6. PIO Signal List

sysIO Buffer

Each I/O is associated with a flexible buffer referred to as a sysIO buffer. These buffers are arranged around the

periphery of the device in groups referred to as banks. The sysIO buffers allow users to implement a wide variety of

standards that are found in today’s systems with LVCMOS interfaces.

Pin Name I/O Type Description

OUTPUT_CLK Input Output register clock

CLOCK_ENABLE Input Clock enable

INPUT_CLK Input Input register clock

OUTPUT_ENABLE Input Output enable

D_OUT_0/1 Input Data from the core

D_IN_0/1 Output Data to the core

LATCH_INPUT_VALUE Input Latches/holds the Input Value

(1,0)

Pad

CLOCK_ENABLE

OUTPUT_ENABLE

OUTPUT_CLK

INPUT_CLK

LATCH_INPUT_VALUE

D_IN_1

D_IN_0

D_OUT_1

D_OUT_0

D_IN_1

D_IN_0

D_OUT_1

D_OUT_0

PIO Pair

= Statically defined by configuration program.

_:,-_: LATTICE 55555555555555

2-10

Architecture

iCE40 UltraLite Family Data Sheet

Typical I/O Behavior During Power-up

The internal power-on-reset (POR) signal is deactivated when VCC, SPI_VCCIO, and VPP_2V5 reach the level

defined in the Power-On-Reset Voltage table in the DC and Switching Characteristics chapter of this data sheet.

After the POR signal is deactivated, the FPGA core logic becomes active. You must ensure that all VCCIO banks

are active with valid input logic levels to properly control the output logic states of all the I/O banks that are critical

to the application. The default configuration of the I/O pins in a device prior to configuration is tri-stated with a weak

pull-up to VCCIO. The I/O pins maintain the pre-configuration state until VCC, SPI_VCCIO, and VPP_2V5 reach the

defined levels. The I/Os take on the software user-configured settings only after POR signal is deactivated and the

device performs a proper download/configuration. Unused I/Os are automatically blocked and the pull-up termina-

tion is disabled.

Supported Standards

The iCE40 UltraLite sysIO buffer supports both single-ended input/output standards, and used as differential com-

parators. The buffer supports the LVCMOS 1.8, 2.5, and 3.3 V standards. The buffer has individually configurable

options for bus maintenance (weak pull-up or none).

Table 2-7 and Table 2-8 show the I/O standards (together with their supply and reference voltages) supported by

the iCE40 UltraLite devices.

Programmable Pull Up Resistors

The iCE40 UltraLite sysIO buffer can be configured with programmable pull up resistors on every I/O. The options

are 3.3 kOhms, 6.8 kOhms, 10 kOhms or 100 kOhms (default). This feature is useful in supporting the I2C interface.

The user can also use it for other purposes.

Differential Comparators

The iCE40 UltraLite devices provide differential comparator on pairs of I/O pins. These comparators are useful in

some mobile applications. Please refer to the Pin Information Summary section to locate the corresponding paired

I/Os with differential comparators.

Table 2-7. Supported Input Standards

Table 2-8. Supported Output Standards

Input Standard VCCIO (Typical)

3.3 V 2.5 V 1.8 V

Single-Ended Interfaces

LVCMOS33 Ye s

LVCMOS25 Ye s

LVCMOS181Ye s

1. Not supported in bank 0 for 16-WLCP package.

Output Standard VCCIO (Typical)

Single-Ended Interfaces

LVCMOS33 3.3 V

LVCMOS25 2.5 V

LVCMOS1811.8 V

1. Not supported in bank 0 for 16-WLCP package.

_:,-_: LATTICE 55555555555555

2-11

Architecture

iCE40 UltraLite Family Data Sheet

On-Chip Oscillator

The iCE40 UltraLite devices feature two different frequency Oscillator. One is tailored for low-power operation that

runs at low frequency (LFOSC). Both Oscillators are controlled with internally generated current.

The LFOSC runs at nominal frequency of 10 kHz. The high frequency oscillator (HFOSC) runs at a nominal fre-

quency of 48 MHz, divisible to 24 MHz, 12 MHz, or 6 MHz, by user option. The LFOSC can be used to perform all

always-on functions, with the lowest power possible. The HFOSC can be enabled when the always-on functions

detect a condition that would need to wake up the system to perform higher frequency functions.

User I2C IP

The iCE40 UltraLite devices have two I2C IP cores. Either of the two cores can be configured either as an I2C mas-

ter or as an I2C slave. The pins for the I2C interface are not pre-assigned. User can use any General Purpose I/O

pins.

In each of the two cores, there are options to delay the either the input or the output, or both, by 50 ns nominal,

using dedicated on-chip delay elements. This provides an easier interface with any external I2C components.

In optional FIFO mode, FIFOs are used for storing multiple bytes of data for transmit and / or receive in order to effi-

ciently support the I2C sensor applications

When the IP core is configured as master, it will be able to control other devices on the I2C bus through the pre-

assigned pin interface. When the core is configured as the slave, the device will be able to provide I/O expansion to

an I2C Master. The I2C cores support the following functionality:

• Master and Slave operation

• 7-bit and 10-bit addressing

• Multi-master arbitration support

• Clock stretching

• Up to 1 MHz data transfer speed

• General Call support

• Optionally delaying input or output data, or both

• Optional FIFO mode

• Transmit FIFO size is 10 bits x 16 bytes, receive FIFO size is 10 bits x 32 bytes

For further information on the User I2C, please refer to TN1274, iCE40 SPI/I2C Hardened IP Usage Guide.

High Current LED Drive I/O Pins

The iCE40 UltraLite family devices offer multiple high current LED drive outputs in each device in the family to allow

the iCE40 UltraLite product to drive LED signals directly on mobile applications.

There are three outputs on each device that can sink up to 24 mA current. These outputs are open-drain outputs,

and provides sinking current to an LED connecting to the positive supply. These three outputs are designed to drive

the RBG LEDs, such as the service LED found in a lot of mobile devices. An embedded RGB PWM IP is also

offered in the family. This RGB drive current is user programmable from 4 mA to 24 mA, in increments of 4 mA in

full current mode or from 2 mA to 12 mA, in increments of 2 mA in half current mode. This output functions as Gen-

eral Purpose I/O with open-drain when the high current drive is not needed.

There is one output on each device that can sink up to 100 mA current. This output is open-drain, and provides

sinking current to drive an external Barcode LED connecting to the positive supply. This Barcode drive current is

user programmable from 16.6 mA to100 mA in increments of 16.6 mA in full current mode or 8.3 mA to 50 mA in

_:,-_: LATTICE 55555555555555

2-12

Architecture

iCE40 UltraLite Family Data Sheet

increments of 8.3 mA in half current mode. This output functions as General Purpose I/O with open drain when the

high current drive is not needed.

There is one output on each device that can sink up to 400 mA current. This output is open-drain, and provides

sinking current to drive an external IR LED connecting to the positive supply. This IR drive current is user program-

mable from 50 mA to 400 mA in increments of 50 mA in full current mode or from 25mA to 200mA in increments of

25mA in half current mode. This output functions as General Purpose I/O with open-drain when the high current

drive is not needed. This output pin can also bond together with the Barcode output to drive higher current for IR

LED.

The 400 mA IR LED drive output and the 100 mA Barcode LED drive output can be connected together to drive up

to 500 mA IR LED, if higher than 400 mA driving capability is needed.

Table 2-9 shows the different LED driving current in the different selected Current Modes. IR500 LED applies with

both IR LED and Barcode LED pins connected together.

Table 2-9. Current Drive

Hardened RGB PWM IP

To provide an easier usage of the RGB high current drivers to drive RGB LED, a Pulse-Width Modulator IP can be

embedded into the user design. This PWM IP provides the flexibility for user to dynamically change the settings on

the ON-time duration, OFF-time duration, and ability to turn the LED lights on and off gradually with user set

breath-on and breath-off time.

For additional information on the PWM IP, please refer to TN1288, iCE40 LED Driver Usage Guide.

Hardened IR Transceiver IP

The IR Transceiver hard IP provides logic function to transmit and receive data through the Infrared LED data link.

It takes the data residing inside the FPGA fabric to transmit with user specified frequency. In user enabled learning

mode, it receives data from Infrared receiver and send the received data back to the FPGA fabric along with the

measured receiving frequency.

For additional information on IR Transceiver IP, please see TN1288, iCE40 LED Driver Usage Guide.

Non-Volatile Configuration Memory

All iCE40 UltraLite devices provide a Non-Volatile Configuration Memory (NVCM) block which can be used to con-

figure the device.

For more information on the NVCM, please refer to TN1248, iCE40 Programming and Configuration.

Power On Reset

iCE40 UltraLite devices have power-on reset circuitry to monitor VCC, SPI_VCCIO1, and VPP_2V5 voltage levels

during power-up and operation. At power-up, the POR circuitry monitors these voltage levels. It then triggers

Full Current Mode Half Current Mode

mA (VCCIO= 3.3 V) mA (VCCIO=2.5 V) mA (VCCIO= 3.3 V) mA (VCCIO=2.5 V)

RGB LED 0, 4, 8, 12, 16, 20, 24 not allowed 0, 2, 4, 6, 8, 10, 12 0, 2, 4, 6, 8, 10, 12

BARCODE LED 0, 16.6, 33.3, 50, 66.6,

83.3, 100

not allowed 0, 8.3, 16.6, 25, 33.3,

41.6, 50

not allowed

IR400 LED 0, 50, 100, 150, 200,

250, 300, 350, 400

not allowed 0, 25, 50, 75, 100, 125,

150, 175, 200

0, 25, 50, 75, 100, 125,

150, 175, 200

IR500 LED 0, 50, 100, 150, 200,

250, 300, 350, 400, 450,

500

not allowed 0, 25, 50, 75, 100, 125,

150, 175, 200, 225, 250

0,25, 50, 75, 100, 125,

150, 175, 200, 225, 250

_:,-_: LATTICE 55555555555555

2-13

Architecture

iCE40 UltraLite Family Data Sheet

download from either the internal NVCM or the external Flash memory after reaching the power-up levels speci-

fied in the Power-On-Reset Voltage table in the DC and Switching Characteristics section of this data sheet. All

power supplies should be powered up during configuration. Before and during configuration, the I/Os are held in

tri-state. I/Os are released to user functionality once the device has finished configuration.

_:,-_: LATTICE 55555555555555

2-14

Architecture

iCE40 UltraLite Family Data Sheet

iCE40 UltraLite Programming and Configuration

This section describes the programming and configuration of the iCE40 UltraLite family.

Device Programming

The NVCM memory can be programmed through the SPI port. The SPI port is located in Bank 1, using

SPI_VCCIO01 power supply.

Device Configuration

There are various ways to configure the Configuration RAM (CRAM), using SPI port, including:

• From a SPI Flash (Master SPI mode)

• System microprocessor to drive a Serial Slave SPI port (SSPI mode)

For more details on configuring the iCE40 UltraLite, please see TN1248, iCE40 Programming and Configuration.

Power Saving Options

The iCE40 UltraLite devices feature iCEGate and PLL low power mode to allow users to meet the static and

dynamic power requirements of their applications. Table 2-10 describes the function of these features.

Table 2-10. iCE40 UltraLite Power Saving Features Description

Device Subsystem Feature Description

PLL When LATCHINPUTVALUE is enabled, puts the PLL into low-power mode; PLL output held static at

last input clock value.

iCEGate

To save power, the optional iCEGate latch can selectively freeze the state of individual, non-regis-

tered inputs within an I/O bank. Registered inputs are effectively frozen by their associated clock or

clock-enable control.

_.'_.'_.' LATTICE CCCCCCCCCCCCC

www.latticesemi.com 3-1 DS1050 DC and Switching_01.4

November 2016 Data Sheet DS1050

or product names are trademarks or registered trademarks of their respective holders. The specifications and information herein are subject to change without notice.

Absolute Maximum Ratings1, 2, 3

Supply Voltage VCC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . –0.5 V to 1.42 V

Output Supply Voltage VCCIO . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . –0.5 V to 3.60 V

NVCM Supply Voltage VPP_2V5 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . –0.5 V to 3.60 V

PLL Supply Voltage VCCPLL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . –0.5 V to 1.30 V

I/O Tri-state Voltage Applied. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . –0.5 V to 3.60 V

Dedicated Input Voltage Applied . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . –0.5 V to 3.60 V

Storage Temperature (Ambient). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . –65 °C to 150 °C

Junction Temperature (TJ) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . –65 °C to 125 °C

1. Stress above those listed under the “Absolute Maximum Ratings” may cause permanent damage to the device. Functional operation of the

device at these or any other conditions above those indicated in the operational sections of this specification is not implied.

2. Compliance with the Lattice Thermal Management document is required.

3. All voltages referenced to GND.

iCE40 UltraLite Family Data Sheet

DC and Switching Characteristics

_:_:_: LATTICE 55555555555555

3-2

DC and Switching Characteristics

iCE40 UltraLite Family Data Sheet

Recommended Operating Conditions1

Power Supply Ramp Rates1, 2

Power-On Reset

All iCE40 UltraLite devices have on-chip Power-On-Reset (POR) circuitry to ensure proper initialization of the

device. Only three supply rails are monitored by the POR circuitry as follows: (1) VCC, (2) SPI_VCCIO1 and (3)

VPP_2V5. All other supply pins have no effect on the power-on reset feature of the device. Note that all supply volt-

age pins must be connected to power supplies for normal operation (including device configuration).

Power-Up Supply Sequencing

It is recommended to bring up the power supplies in the following order. Note that there is no specified timing delay

between the power supplies, however, there is a requirement for each supply to reach a level of 0.5V, or higher,

before any subsequent power supplies in the sequence are applied.

1. VCC and VCCPLL should be the first two supplies to be applied. Note that these two supplies can be tied

together subject to the recommendation to include a RC-based noise filter on the VCCPLL (Please refer to

TN1252, iCE40 Hardware Checklist.)

2. SPI_VCCIO1 should be the next supply, and can be applied any time after the previous supplies (VCC and

VCCPLL) have reached as level of 0.5 V or higher.

3. VPP_2V5 should be the next supply, and can be applied any time after previous supplies (VCC, VCCPLL and

SPI_VCCIO1) have reached a level of 0.5 V or higher.

4. Other Supplies (VCCIO0 and VCCIO2) do not affect device power-up functionality, and they can be applied any

time after the initial power supplies (VCC and VCCPLL) have reached a level of 0.5 V or greater. On the 16

Symbol Parameter Min. Max. Units

VCC1Core Supply Voltage 1.14 1.26 V

VPP_2V5 VPP_2V5 NVCM Programming and

Operating Supply Voltage

Slave SPI Configuration 1.7143.46 V

Master SPI Configuration 2.30 3.46 V

Configuration from NVCM 2.30 3.46 V

NVCM Programming 2.30 3.00 V

VCCIO1, 2, 3 I/O Driver Supply Voltage VCCIO_0, SPI_VCCIO1, VCCIO_2 1.71 3.46 V

VCCPLL PLL Supply Voltage 1.14 1.26 V

tJCOM Junction Temperature Commercial Operation 0 85 °C

tJIND Junction Temperature Industrial Operation –40 100 °C

tPROG Junction Temperature NVCM Programming 10 30 °C

1. Like power supplies must be tied together if they are at the same supply voltage and they meet the power up sequence requirement. Please

refer to Power-Up Supply Sequencing section. VCC and VCCPLL are recommended to tie to same supply with an RC-based noise filter

between them. Please refer to TN1252, iCE40 Hardware Checklist.

2. See recommended voltages by I/O standard in subsequent table.

3. VCCIO pins of unused I/O banks should be connected to the VCC power supply on boards.

4. VPP_2V5 can, optionally, be connected to a 1.8 V (+/-5%) power supply in Slave SPI Configuration mode subject to the condition that none of

the HFOSC/LFOSC and RGB LED / IR / Barcode LED driver features are used. Otherwise, VPP_2V5 must be connected to a power supply

with a minimum 2.30 V level.

Symbol Parameter Min. Max. Units

tRAMP Power supply ramp rates for all power supplies. 0.6 10 V/ms

1. Assumes monotonic ramp rates.

2. Power-up sequence must be followed. Please refer to Power-Up Supply Sequencing section.

ﬂ: LATTICE .- lsstoNnucrap

3-3

DC and Switching Characteristics

iCE40 UltraLite Family Data Sheet

WLCSP package, VCCIO0 and VPP_2V5 are connected to the same pin on the package, and should be pow-

ered as VPP_2V5 in the sequence.

There is no power down sequence required. However, when partial power supplies are powered down, it is

required the above sequence to be followed when these supplies are repowered up again.

External Reset

When all power supplies have reached to their minimum operating voltage defined in Minimum Operation Condition

Table, it is required to either keep CRESET_B LOW, or toggle CRESET_B from HIGH to LOW, for a duration of

tCRESET_B, and release it to go HIGH, to start configuration download from either the internal NVCM or the external

Flash memory.

Figure 3-1 shows Power-Up sequence when SPI_VCCIO1 and VPP_2V5 are connected separately, and the

CRESET_B signal triggers configuration download. Figure 3-2 shows when SPI_VCCIO1 and VPP_2V5 connected

together. If the supply sequence is not followed, extra peak current may be observed on the supplies during power

up.

All power supplies should be powered up during configuration. Before and during configuration, the I/Os are held in

tri-state. I/Os are released to user functionality once the device has finished configuration.

Figure 3-1. Power Up Sequence with SPI_VCCIO1 and VPP_2V5 Not Connected Together

Figure 3-2. Power Up Sequence with All Supplies Connected Together

VCC/VCC_PLL = 1.2 V

SPI_VCCIO1 = 1.8 V

VPP_2V5, VCCIO0 and VCCIO2= 2.5 V / 3.3 V

0.5 V

CRESET_B

tCRESET_B

VSUPPLY(MIN)

VCC/VCC_PLL = 1.2 V

SPI_VCCIO, VPP_2V5, VCCIO0 and VCCIO2= 1.8 V / 2.5 V / 3.3 V

0.5 V

VSUPPLY(MIN)

CRESET_B

tCRESET_B

_:_:_: LATTICE 55555555555555

3-4

DC and Switching Characteristics

iCE40 UltraLite Family Data Sheet

Power-On-Reset Voltage Levels1

ESD Performance

Please contact Lattice Semiconductor for additional information.

DC Electrical Characteristics

Over Recommended Operating Conditions

Symbol Parameter Min. Max. Units

VPORUP Power-On-Reset ramp-up trip point (circuit monitoring

VCC, SPI_VCCIO1, VPP_2V5)

VCC 0.6 1 V

SPI_VCCIO1 0.7 1.6 V

VPP_2V5 0.7 1.6 V

VPORDN Power-On-Reset ramp-down trip point (circuit monitor-

ing VCC, SPI_VCCIO1, VPP_2V5)

VCC —0.85 V

SPI_VCCIO1 —1.6 V

VPP_2V5 —1.6 V

1. These POR trip points are only provided for guidance. Device operation is only characterized for power supply voltages specified under rec-

ommended operating conditions.

Symbol Parameter Condition Min. Typ. Max. Units

IIL, IIH1, 3, 4 Input or I/O Leakage 0V < VIN < VCCIO + 0.2 V — — +/–10 µA

C1I/O Capacitance2VCCIO = 3.3 V, 2.5 V, 1.8 V

VCC = Typ., VIO = 0 to VCCIO + 0.2 V —6—pf

C2Global Input Buffer

Capacitance2

VCCIO = 3.3 V, 2.5 V, 1.8 V

VCC = Typ., VIO = 0 to VCCIO + 0.2 V —6—pf

C324 mA LED I/O Capacitance VCCIO = 3.3 V, 2.5 V, 1.8 V

VCC = Typ., VIO = 0 to VCCIO + 0.2 V —20— pf

C4400 mA LED I/O Capacitance VCCIO = 3.3 V, 2.5 V, 1.8 V

VCC = Typ., VIO = 0 to VCCIO + 0.2 V —53— pf

C5100 mA LED I/O Capacitance VCCIO = 3.3 V, 2.5 V, 1.8 V

VCC = Typ., VIO = 0 to VCCIO + 0.2 V —20— pf

VHYST Input Hysteresis VCCIO = 1.8 V, 2.5 V, 3.3 V — 200 — mV

IPU Internal PIO Pull-up

Current

VCCIO = 1.8 V, 0=<VIN<=0.65 VCCIO –3—–31 µA

VCCIO = 2.5 V, 0=<VIN<=0.65 VCCIO –8—–72 µA

VCCIO = 3.3 V, 0=<VIN<=0.65 VCCIO –11 — –128 µA

1. Input or I/O leakage current is measured with the pin configured as an input or as an I/O with the output driver tri-stated. It is not measured

with the output driver active. Internal pull-up resistors are disabled.

2. TJ 25°C, f = 1.0 MHz.

3. Please refer to VIL and VIH in the sysIO Single-Ended DC Electrical Characteristics table of this document.

4. Input pins are clamped to VCCIO and GND by a diode. When input is higher than VCCIO or lower than GND, the Input Leakage current will be

higher than the IIL and IIH.

_:_:_: LATTICE 55555555555555

3-5

DC and Switching Characteristics

iCE40 UltraLite Family Data Sheet

Supply Current 1, 2, 3, 4, 5

Internal Pull-Up Resistor Specifications

User I2C Specifications1

Symbol Parameter

Typ. VCC =

1.2 V4Units

ICCSTDBY Core Power Supply Static Current 35 µA

IPP2V5STDBY VPP_2V5 Power Supply Static Current 1 µA

ICCPLLSTDBY PLL Power Supply Static Current 1 µA

ICCIOSTDBY VCCIO Power Supply Static Current 1 at VCCIO equal or less

2.5 V; 5 at VCCIO equal

or less 3.465 V

µA

ICCPEAK Core Power Supply Startup Peak Current 3.06 mA

IPP_2V5PEAK VPP_2V5 Power Supply Startup Peak Current 2.15 mA

ICCPLLPEAK PLL Power Supply Startup Peak Current 3.066mA

ICCIOPEAK VCCIO Power Supply Startup Peak Current 4.65 for config bank, 0.25

for regular IO bank

1. Assumes programmed pattern with the following characteristics: all outputs are tri-stated, all inputs are configured as LVCMOS and held at

VCCIO or GND, on-chip PLL is off. For more detail with your specific design, use the Power Calculator tool. Power specified with master SPI

configuration mode. Other modes may be up to 25% higher.

2. Frequency = 0 MHz.

3. TJ = 25 °C, power supplies at nominal voltage.

4. Does not include pull-up.

5. Peak current is the in rush current - highest current during power supply start up within the power supply ramp rate. See Power Supply

Ramp Rates1, 2 section. These currents are measured with decoupling capacitance of 0.1 uF, 10 nF, and 1 nF to the power supply. Higher

decoupling capacitance causes higher current.

6. PLL power supply shared with Core Power supply.

Parameter Condition Spec Units

Min Typ Max

Resistor_3.3K 1.71 < Vccio < 3.47 V 2.64 3.3 3.96 kOhm

Resistor_6.8K 1.71 < Vccio < 3.47 V 5.44 6.8 8.16 kOhm

Resistor_10K 1.71 < Vccio < 3.47 V 8 10 12 kOhm

Weak pull-up resistor

1.71 < Vccio < 1.89 V — 100 — kOhm

2.38 < Vccio < 2.63 V — 55 — kOhm

3.13 < Vccio < 3.47 V — 40 — kOhm

SN Symbol Parameter STD Mode FAST Mode FAST Mode Plus

Min Max Min Max Min Max Units

1 fSCL SCL clock frequency 100 400 10002kHz

1. Refer to the I2C specification for timing requirements.

2. Fast Mode Plus maximum speed may be achieved by using external pull up resistor on I2C bus. Internal pull up may not be sufficient to sup-

port the maximum speed.

_:_:_: LATTICE 55555555555555

3-6

DC and Switching Characteristics

iCE40 UltraLite Family Data Sheet

Internal Oscillators (HFOSC, LFOSC)

sysIO Recommended Operating Conditions

sysIO Single-Ended DC Electrical Characteristics

Differential Comparator Electrical Characteristics

Derating Logic Timing

Logic timing provided in the following sections of the data sheet and the Lattice design tools are worst case num-

bers in the operating range. Actual delays may be much faster. Lattice design tools can provide logic timing num-

bers at a particular temperature and voltage.

Parameter Parameter Description Spec/Recommended Units

Symbol Conditions Min Typ Max

fCLKHF

Commercial Temp HFOSC clock frequency (tJ = 0 oC–85 oC) –10% 48 10% MHz

Industrial Temp HFOSC clock frequency (tJ = –40 oC–100 oC) –20% 48 20% MHz

fCLKLF LFOSC CLKK clock frequency –10% 10 10% kHz

DCHCLKHF

Commercial Temp HFOSC clock frequency (tJ = 0 oC–85 oC) 45 50 55 %

Industrial Temp HFOSC clock frequency (tJ = –45 oC–100 oC) 40 50 60 %

DCHCLKLF LFOSC Duty Cycle (Clock High Period) 45 50 55 %

tWAKEUP Delay OSC Enable to output enable delay — — 100 µs

Tsync_on Oscillator output synchronizer delay — — 5 Cycles

Tsync_off Oscillator output disable delay — — 5 Cycles

Standard

VCCIO (V)

Min. Typ. Max.

LVCMOS 3.3 3.14 3.3 3.46

LVCMOS 2.5 2.37 2.5 2.62

LVCMOS 1.8 1.71 1.8 1.89

Input/

Output

Standard

VIL VIH VOL Max.

(V)

VOH Min.

(V)

IOL Max.

(mA)

IOH Max.

(mA)Min. (V) Max. (V) Min. (V) Max. (V)

LVCMOS 3.3 -0.3 0.8 2.0 VCCIO + 0.2V 0.4 VCCIO - 0.4 8 –8

0.2 VCCIO - 0.2 0.1 –0.1

LVCMOS 2.5 -0.3 0.7 1.7 VCCIO + 0.2V 0.4 VCCIO - 0.4 6 –6

0.2 VCCIO - 0.2 0.1 –0.1

LVCMOS 1.8 -0.3 0.35VCCIO 0.65VCCIO VCCIO + 0.2V 0.4 VCCIO - 0.4 4 –4

0.2 VCCIO - 0.2 0.1 –0.1

Parameter

Symbol Parameter Description

Test

Conditions Min. Max. Units

VREF Reference Voltage to compare, on VINM VCCIO = 2.5 V 0.25 VCCIO –0.25 V V

VDIFFIN_H Differential input HIGH (VINP - VINM)V

CCIO = 2.5 V 250 — mV

VDIFFIN_L Differential input LOW (VINP - VINM)V

CCIO = 2.5 V — –250 mV

IIN Input Current, VINP and VINM VCCIO = 2.5 V –10 10 µA

_:_:_: LATTICE 55555555555555

3-7

DC and Switching Characteristics

iCE40 UltraLite Family Data Sheet

Maximum sysIO Buffer Performance1

iCE40 UltraLite External Switching Characteristics

Over Recommended Operating Conditions

I/O Standard Max. Speed Units

Inputs

LVCMOS33 250 MHz

LVCMOS25 250 MHz

LVCMOS18 250 MHz

LED I/O used as GPIO open drain 50 MHz

Outputs

LVCMOS33 250 MHz

LVCMOS25 250 MHz

LVCMOS18 155 MHz

LED I/O used as GPIO open drain 502MHz

1. Measured with a toggling pattern.

2. With external resistor from 180 Ohm to 250 Ohm and capacity of no more than 15 pF.

Parameter Description Device Min Max Units

Global Clocks

fMAX_GBUF Frequency for Global Buffer Clock network All devices — 185 MHz

tW_GBUF Clock Pulse Width for Global Buffer All devices 2 — ns

tSKEW_GBUF Global Buffer Clock Skew Within a Device All devices — 500 ps

Pin-LUT-Pin Propagation Delay

tPD Best case propagation delay through one

LUT logic All devices — 9.0 ns

General I/O Pin Parameters (Using Global Buffer Clock without PLL)1

tSKEW_IO Data bus skew across a bank of IOs All devices — 410 ps

tCO Clock to Output - PIO Output Register All devices — 9.0 ns

tSU Clock to Data Setup - PIO Input Register All devices –0.5 — ns

tHClock to Data Hold - PIO Input Register All devices 5.55 — ns

General I/O Pin Parameters (Using Global Buffer Clock with PLL)

tCOPLL Clock to Output - PIO Output Register All Devices — 2.9 ns

tSUPLL Clock to Data Setup - PIO Input Register All Devices 7.9 — ns

tHPLL Clock to Data Hold - PIO Input Register All Devices –0.6 — ns

1. All the data is from the worst case condition.

_:_:_: LATTICE 55555555555555

3-8

DC and Switching Characteristics

iCE40 UltraLite Family Data Sheet

sysCLOCK PLL Timing

Over Recommended Operating Conditions

SPI Master or NVCM Configuration Time1, 2

Parameter Descriptions Conditions Min. Max. Units

fIN Input Clock Frequency

(REFERENCECLK, EXTFEEDBACK) 10 133 MHz

fOUT Output Clock Frequency (PLLOUT) 16 275 MHz

fVCO PLL VCO Frequency 533 1066 MHz

fPFD Phase Detector Input Frequency 10 133 MHz

AC Characteristics

tDT Output Clock Duty Cycle 40 60 %

tPH Output Phase Accuracy — +/–12 deg

tOPJIT1, 5

Output Clock Period Jitter fOUT >= 100 MHz — 450 ps p-p

fOUT < 100 MHz — 0.05 UIPP

Output Clock Cycle-to-cycle Jitter fOUT >= 100 MHz — 750 ps p-p

fOUT < 100 MHz — 0.10 UIPP

Output Clock Phase Jitter fPFD >= 25 MHz — 275 ps p-p

fPFD < 25 MHz — 0.05 UIPP

tWOutput Clock Pulse Width At 90% or 10% 1.33 — ns

tLOCK2, 3 PLL Lock-in Time — 50 µs

tUNLOCK PLL Unlock Time — 50 ns

tIPJIT4Input Clock Period Jitter fPFD  20 MHz — 1000 ps p-p

fPFD < 20 MHz — 0.02 UIPP

tSTABLE3LATCHINPUTVALUE LOW to PLL Stable — 500 ns

tSTABLE_PW3LATCHINPUTVALUE Pulse Width 100 — ns

tRST RESET Pulse Width 10 — ns

tRSTREC RESET Recovery Time 10 — µs

tDYNAMIC_WD DYNAMICDELAY Pulse Width 100 — VCO

Cycles

1. Period jitter sample is taken over 10,000 samples of the primary PLL output with a clean reference clock. Cycle-to-cycle jitter is taken over

1000 cycles. Phase jitter is taken over 2000 cycles. All values per JESD65B.

2. Output clock is valid after tLOCK for PLL reset and dynamic delay adjustment.

3. At minimum fPFD. As the fPFD increases the time will decrease to approximately 60% the value listed.

4. Maximum limit to prevent PLL unlock from occurring. Does not imply the PLL will operate within the output specifications listed in this table.

5. The jitter values will increase with loading of the PLD fabric and in the presence of SSO noise.

Symbol Parameter Conditions Max. Units

tCONFIG POR/CRESET_B to Device I/O Active

All devices - Low Frequency (Default) 53 ms

All devices - Medium frequency 25 ms

All devices - High frequency 13 ms

1. Assumes sysMEM Block is initialized to an all zero pattern if they are used.

2. The NVCM download time is measured with a fast ramp rate starting from the maximum voltage of POR trip point.

_:_:_: LATTICE 55555555555555

3-9

DC and Switching Characteristics

iCE40 UltraLite Family Data Sheet

sysCONFIG Port Timing Specifications

Symbol Parameter Conditions Min. Typ. Max. Units

All Configuration Modes

tCRESET_B

Minimum CRESET_B LOW pulse width

required to restart configuration, from

falling edge to rising edge

200 — — ns

tDONE_IO

Number of configuration clock cycles

after CDONE goes HIGH before the

PIO pins are activated

49 — — Clock

Cycles

Slave SPI

tCR_SCK

Minimum time from a rising edge on

CRESET_B until the first SPI WRITE

operation, first SPI_XCK clock. During

this time, the iCE40 UltraLite device is

clearing its internal configuration mem-

ory

1200 — — µs

fMAX CCLK clock frequency Write 1 — 25 MHz

Read1—15—MHz

tCCLKH CCLK clock pulsewidth HIGH 20 — — ns

tCCLKL CCLK clock pulsewidth LOW 20 — — ns

tSTSU CCLK setup time 12 — — ns

tSTH CCLK hold time 12 — — ns

tSTCO CCLK falling edge to valid output 13 — — ns

Master SPI3

fMCLK MCLK clock frequency

Low Frequency

(Default)

7.0 12.0 17.0 MHz

Medium Frequency221.0 33.0 45.0 MHz

High Frequency233.0 53.0 71.0 MHz

tMCLK CRESET_B HIGH to first MCLK edge 1200 — — µs

tMTSU MCLK setup time49.9 — — ns

tMTH MCLK hold time 1 — — ns

1. Supported with 1.2 V Vcc and at 25 C.

2. Extended range fMAX Write operations support up to 53 MHz with 1.2 V VCC and at 25 C.

3. tSU and tHD timing must be met for all MCLK frequency choices

4. For considerations of SPI Master Configuration Mode, please refer to TN1248, iCE40 Programming and Configuration.

_:_:_: LATTICE 55555555555555

3-10

DC and Switching Characteristics

iCE40 UltraLite Family Data Sheet

High Current LED, IR LED and Barcode LED Drives1

RGB LED Timing Specification

IR Transceiver IP Timing Specification

Symbol Parameter VCCIO = 3.3 V VCCIO = 2.5 V

Min. Max. Units Min. Max. Units

IRGB_ACCURACY_FULL RGB LED0, LED1, LED2 Sink Cur-

rent Accuracy to selected current

@ 

VPAD = 0.5 ~ 2.5 V

–12 +12 % not

allowed

not

allowed

IRGB_ACCURACY_HALF RGB LED0, LED1, LED2 Sink Cur-

rent Accuracy to selected current

@ 

VPAD = 0.35 ~ 2.5 V

–14 +14 % –14 +14 %

IRGB_MATCH RGB LED0, LED1, LED2 Sink Cur-

rent Matching among the 3 outputs

@ 

VPAD = 0.35 ~ 2.5 V

–5+5 % –5+5 %

IIR_ACCURACY_FULL IR LED Sink Current Accuracy to

selected current @ VPAD = 

0.8 V ~ 2 V

–12 +12 % not

allowed

not

allowed

IIR_ACCURACY_HALF IR LED Sink Current Accuracy to

selected current @ VPAD = 

0.55 V ~ 2 V

–12 +12 % –12 +12 %

IBARCODE_ACCURACY_FULL BARCODE LED Sink Current

Accuracy to selected current @

VPAD = 

0.8 V ~ 2 V

–12 +12 % not

allowed

not

allowed

IBARCODE_ACCURACY_HALF BARCODE LED Sink Current

Accuracy to selected current @

VPAD = 

0.55 V ~ 2 V

–12 +12 % not

allowed

not

allowed

1. Refer to Table 2-9 for valid current settings.

SN Symbol Parameter Min TYP Max Units

PWM_OUT_X

FR250 = 0

Frequency of the PWM output for color LED;

When FR250 = 0

125 Hz

PWM_OUT_X

FR250 = 1

Frequency of the PWM output for color LED;

When FR250 = 1

250 Hz

HIGH_X PWM High percentage for color LED. 0 99 %

HIGH_STEP_X PWM High percentage incremental step. 1/256 %

SN Symbol Parameter Min TYP Max Units

IR_OUT Frequency of the IR output 25 120 kHz

IR_IN Frequency of the IR input 25 120 kHz

HIGH (DUTY1/3 = 0) Duty Cycle when DUTY1/3 = 0. 50 %

HIGH (DUTY1/3 = 1) Duty Cycle when DUTY1/3 = 1. 33.33 %

_:,-_: LATTICE 55555555555555 n1

3-11

DC and Switching Characteristics

iCE40 UltraLite Family Data Sheet

Switching Test Conditions

Figure 3-3 shows the output test load used for AC testing. The specific values for resistance, capacitance, voltage,

and other test conditions are shown in Table 3-1.

Figure 3-3. Output Test Load, LVCMOS Standards

Table 3-1. Test Fixture Required Components, Non-Terminated Interfaces

Test Condition R1CLTiming Reference VT

LVCMOS settings (L -> H, H -> L) 0 pF

LVCMOS 3.3 = 1.5 V —

LVCMOS 2.5 = VCCIO/2 —

LVCMOS 1.8 = VCCIO/2 —

LVCMOS 3.3 (Z -> H)

188 0 pF

1.5 V VOL

LVCMOS 3.3 (Z -> L) 1.5 V VOH

Other LVCMOS (Z -> H) VCCIO/2 VOL

Other LVCMOS (Z -> L) VCCIO/2 VOH

LVCMOS (H -> Z) VOH - 0.15 V VOL

LVCMOS (L -> Z) VOL - 0.15 V VOH

Note: Output test conditions for all other interfaces are determined by the respective standards.

DUT

Test Poi n t

:'_.'_.' LATTICE CCCCCCCCCCCCC

www.latticesemi.com 4-1 DS1050 Pinout Information_01.1

April 2016 Data Sheet DS1050

or product names are trademarks or registered trademarks of their respective holders. The specifications and information herein are subject to change without notice.

Signal Descriptions

Signal Name Function I/O Description

Power Supplies

VCC Power — Core Power Supply

VCCIO_0, SPI_VCCIO1, VCCIO_2 Power — Power for I/Os in Bank 0, 1, and 2. VCCIO0 is tied with

VPP_2V5 and VCCIO2 is tied with SPI_VCCIO1 in 16

WLCS package.

VPP_2V5 Power — Power for NVCM programming and operations

VCCPLL Power — Power for PLL

GND GROUND — Ground

GND_LED GROUND — Ground for LED drivers. Should connect to GND on

board

Configuration

Primary Secondary

CRESETB — Configuration I Configuration Reset, active LOW. Include a weak

internal pull-up resistor to VCCIO_2. Or actively driven

externally or connect an 10K-Ohm pull-up to VCCIO_2.

PIOB_8a CDONE Configuration I/O Configuration Done. Includes a weak pull-up resistor

to VCCIO_2. In 16 WLCS CDONE shared with

PIOB_8a.

General I/O I/O In user mode, after configuration, this pin can be pro-

grammed as general I/O in user function.

PIOB_11b CDONE Configuration I/O Configuration Done. Includes a weak pull-up resistor

to VCCIO_2. In 36-ball ucBGA package CDONE

shared with PIOB_11b.

General I/O I/O In user mode, after configuration, this pin can be pro-

grammed as general I/O in user function.

Config SPI

Primary Secondary

PIOB_16a SPI_SCK Configuration I/O This pin is shared with device configuration. During

configuration:

In Master SPI mode, this pin outputs the clock to

external SPI memory.

In Slave SPI mode, this pin inputs the clock from

external processor.

General I/O I/O In user mode, after configuration, this pin can be pro-

grammed as general I/O in user function.

PIOB_14a SPI_SO Configuration Output This pin is shared with device configuration. During

configuration:

In Master SPI mode, this pin outputs the command

data to external SPI memory.

In Slave SPI mode, this pin connects to the MISO pin

of the external processor.

General I/O I/O In user mode, after configuration, this pin can be pro-

grammed as general I/O in user function.

iCE40 UltraLite Family Data Sheet

Pinout Information

_:_:_: LATTICE 55555555555555

4-2

Pinout Information

iCE40 UltraLite Family Data Sheet

PIOB_15b SPI_SI Configuration Input This pin is shared with device configuration. During

configuration:

In Master SPI mode, this pin receives data from exter-

nal SPI memory.

In Slave SPI mode, this pin connects to the MOSI pin

of the external processor.

General I/O I/O In user mode, after configuration, this pin can be pro-

grammed as general I/O in user function

PIOB_17b SPI_SS_B Configuration I/O This pin is shared with device configuration. During

configuration:

In Master SPI mode, this pin outputs to the external

SPI memory.

In Slave SPI mode, this pin inputs from the external

processor.

General I/O I/O In user mode, after configuration, this pin can be pro-

grammed as general I/O in user function.

Global Signals

Primary Secondary

PIOT_22b G0 General I/O I/O In user mode, after configuration, this pin can be pro-

grammed as general I/O in user function.

Global Input Global input used for high fanout, or clock/reset net.

The G0 pin drives the GBUF0 global buffer.

PIOT_21a G1 General I/O I/O In user mode, after configuration, this pin can be pro-

grammed as general I/O in user function.

Global Input Global input used for high fanout, or clock/reset net.

The G1 pin drives the GBUF1 global buffer.

PIOB_13b G3 General I/O I/O In user mode, after configuration, this pin can be pro-

grammed as general I/O in user function.

Global Input Global input used for high fanout, or clock/reset net.

The G3 pin drives the GBUF3 global buffer.

PIOB_8a G4 General I/O I/O In user mode, after configuration, this pin can be pro-

grammed as general I/O in user function.

Global Input Global input used for high fanout, or clock/reset net.

The G4 pin drives the GBUF4 global buffer.

PIOB_7b G5 General I/O I/O In user mode, after configuration, this pin can be pro-

grammed as general I/O in user function.

Global Input Global input used for high fanout, or clock/reset net.

The G5 pin drives the GBUF5 global buffer.

PIOB_3b G6 General I/O I/O In user mode, after configuration, this pin can be pro-

grammed as general I/O in user function.

Global Input Global input used for high fanout, or clock/reset net.

The G6 pin drives the GBUF6 global buffer.

LED Signals

RGB0 General I/O Open-Drain I/O In user mode, with user's choice, this pin can be pro-

grammed as open drain I/O in user function.

LED Open-Drain

Output

In user mode, with user's choice, this pin can be pro-

grammed as open drain 24mA output to drive exter-

nal LED.

RGB1 General I/O Open-Drain I/O In user mode, with user's choice, this pin can be pro-

grammed as open drain I/O in user function.

LED Open-Drain

Output

In user mode, with user's choice, this pin can be pro-

grammed as open drain 24mA output to drive exter-

nal LED.

_:,-_: LATTICE 55555555555555

4-3

Pinout Information

iCE40 UltraLite Family Data Sheet

RGB2 General I/O Open-Drain I/O In user mode, with user's choice, this pin can be pro-

grammed as open drain I/O in user function.

LED Open-Drain

Output

In user mode, with user's choice, this pin can be pro-

grammed as open drain 24mA output to drive exter-

nal LED.

IRLED General I/O Open-Drain I/O In user mode, with user's choice, this pin can be pro-

grammed as open drain I/O in user function.

LED Open-Drain

Output

In user mode, with user's choice, this pin can be pro-

grammed as open drain 400 mA output to drive exter-

nal LED.

BARCODE General I/O Open-Drain I/O In user mode, with user's choice, this pin can be pro-

grammed as open drain I/O in user function.

LED Open-Drain

Output

In user mode, with user's choice, this pin can be pro-

grammed as open drain 100 mA output to drive exter-

nal LED.

PIOT_xx General I/O I/O In user mode, with user's choice, this pin can be pro-

grammed as I/O in user function in the top (xx = I/O

location).

PIOB_xx General I/O I/O In user mode, with user's choice, this pin can be pro-

grammed as I/O in user function in the bottom (xx = I/

O location).

_:_:_: LATTICE 55555555555555

4-4

Pinout Information

iCE40 UltraLite Family Data Sheet

Pin Information Summary

Pin Type iCE40UL1K iCE40UL640

SWG16 36 ucBGA SWG16 36 ucBGA

General Purpose I/O Per

Bank

Bank 0 5 12 5 12

Bank 1 4 4 4 4

Bank 2 1 10 1 10

Total General Purpose I/Os 10 26 10 26

VCC 1 1 1 1

VCCIO Bank 0 0 1 0 1

Bank 1 0 1 0 1

Bank 2 1 1 1 1

VCCPLL 0101

VCPP_2V5 1 1 1 1

CRESET_B 1 1 1 1

CDONE 0 0 0 0

GND 1 2 1 2

GND_LED 1 1 1 1

Total Balls 16361636

_.'_.'_.' LATTICE CCCCCCCCCCCCC

www.latticesemi.com 5-1 DS1050 Order Info_01.1

April 2016 Data Sheet DS1050

or product names are trademarks or registered trademarks of their respective holders. The specifications and information herein are subject to change without notice.

iCE40 UltraLite Part Number Description

Tape and Reel Quantity

Ordering Part Numbers

Industrial

Package TR Quantity

CM36A 4,000

SWG16 5,000

Part Number LUTs Supply Voltage Package Pins Temp.

ICE40UL1K-SWG16ITR 1248 1.2 Halogen-Free WLCSP 16 IND

ICE40UL1K-CM36AITR 1248 1.2 36-Ball ucBGA 36 IND

ICE40UL1K-CM36AITR1K 1248 1.2 36-Ball ucBGA 36 IND

ICE40UL640-SWG16ITR 640 1.2 Halogen-Free WLCSP 16 IND

ICE40UL640-CM36AITR 640 1.2 36-Ball ucBGA 36 IND

ICE40UL640-CM36AITR1K 640 1.2 36-Ball ucBGA 36 IND

Logic Cells

Package

SWG16 = 16-Ball WLCSP (0.35 mm Ball Pitch)

CM36A = 36-Ball ucBGA (0.40 mm Ball Pitch)

Device Family

iCE40 UltraLite FPGA

iCE40ULXX-XXXXXITR

640 = 640 Logic Cells

1K = 1,248 Logic Cells

Shipping Method

Blank = Trays

TR = Tape and Reel (See quantity below)

TR1K = Tape and Reel, 1,000 units

Grade

I = Industrial

iCE40 UltraLite Family Data Sheet

Ordering Information

_.'_.'_.' LATTICE CCCCCCCCCCCCC

July 2016 Data Sheet DS1050

or product names are trademarks or registered trademarks of their respective holders. The specifications and information herein are subject to change without notice.

www.latticesemi.com 6-1 DS1050 Further Info_01.1

For Further Information

A variety of technical notes for the iCE40 UltraLite family are available on the Lattice web site.

• TN1248, iCE40 Programming and Configuration

• TN1274, iCE40 I2C and SPI Hardened IP Usage Guide

• TN1276, Advanced iCE40 I2C and SPI Hardened IP Usage Guide

• TN1250, Memory Usage Guide for iCE40 Devices

• TN1251, iCE40 sysCLOCK PLL Design and Usage Guide

• TN1252, iCE40 Hardware Checklist

• TN1288, iCE40 LED Driver Usage Guide

• iCE40 UltraLite Pinout Files

• iCE40 UltraLite Pin Migration Files

•Thermal Management document

•Lattice design tools

•Schematic Symbols

iCE40 UltraLite Family Data Sheet

Supplemental Information

_.'_.'_.' LATTICE CCCCCCCCCCCCC

November 2016 Data Sheet DS1050

or product names are trademarks or registered trademarks of their respective holders. The specifications and information herein are subject to change without notice.

www.latticesemi.com 7-1 DS1050 Revision History

Date Version Section Change Summary

November 2016 1.4 DC and Switching

Characteristics

Updated External Reset section. Added information on following supply

sequence.

June 2016 1.3 Introduction Updated General Description section.

— Changed “embedded RGB PWM IP” to ”hardened RGB PWM IP”.

— Changed “modulation logic” to “hardened TX/RX pulse logic”.

— Updated information on the use of 500 mA IR driver.

Updated Introduction section.

— Added “RGB LED and IR LED” to configurable Controllers.

— Added “LED” to RGB control functions.

Architecture Updated Architecture Overview section.

— Changed caption to Figure 2-1, iCE40UL1K iCE40UL-1K Device,

Top View.

— Changed logic blocks to PLB.

— Changed “LED sink” to “RGB and IR LED sinks, and a 100 mA Bar-

code emulation output”.

— Corrected headings in Table 2-2, Global Buffer (GBUF) Connections

to Programmable Logic Blocks.

— Updated footnote in Table 2-4, sysMEM Block Configuration.

— Updated sysIO Buffer Banks section.

— Corrected VCCIO format in Figure 2-5, I/O Bank and Programmable I/O Cell.

— Updated Typical I/O Behavior During Power-up section.

— Updated Supported Standards section.

— Updated Programmable Pull Up Resistors section.

— Changed “more than one byte” to “multiple bytes” in User I2C IP sec-

tion.

— Updated High Current LED Drive I/O Pins section.

Changed heading to High Current LED Drive I/O Pins. Added LED to

“high current drive”. Added information on use of 500 mA IR LED.

Added paragraph to reference Table 2-9.

— Changed heading to Hardened RGB PWM IP.

— Changed heading to Hardened IR Transceiver IP.

Updated iCE40 UltraLite Programming and Configuration section.

Changed VCCIO_1 to SPI_VCCIO1 in Device Programming.

DC and Switching

Characteristics

Updated Absolute Maximum Ratings section. Corrected VPP_2V5 and

VCCPLL format.

Updated Recommended Operating Conditions section.

— Changed heading to Hardened RGB PWM IP.

— Updated footnote.

Removed Power-up Sequence section.

Added the following sections:

— Power-On Reset

— Power-Up Supply Sequencing

— External Reset

Updated DC Electrical Characteristics section. Revised footnote 4.

Updated Supply Current section.

— Changed VPP_2V5 format.

— Updated footnote 5.

Updated Internal Oscillators (HFOSC, LFOSC) section. Added Com-

mercial and Industrial Temp values for fCLKHF and DCHCLKHF

Updated Differential Comparator Electrical Characteristics section.

iCE40 UltraLite Family Data Sheet

Revision History

_:_:_: LATTICE 55555555555555

7-2

Revision History

iCE540 Ultra Family Data Sheet

Updated iCE40 UltraLite External Switching Characteristics section.

Revised footnote.

Updated sysCLOCK PLL Timing section. Revised tOPJIT conditions.

Updated sysCONFIG Port Timing Specifications section.

— Added footnote to Master SPI.

— Added footnote to MCLK setup time.

— Revised tMTSU minimum value.

— Added footnotes 3 and 4.

Supplemental

Information

Updated For Further Information section. Added reference to TN1252,

iCE40 Hardware Checklist.

April 2016 1.2 Introduction Updated Features section.

— Updated BGA package to ucBGA.

— Corrected HF Oscillator unit in Table 1-1, iCE40 UltraLite Family

Selection Guide.

Architecture Updated sysCLOCK Phase Locked Loops (PLLs) (sysCLOCK PLL is

only supported in 36-ball ucBGA package) section. Updated BGA pack-

age to ucBGA in heading.

DC and Switching

Characteristics

Updated Recommended Operating Conditions section. Added footnote

4 regarding VPP_2V5.

Pinout Information Updated Signal Descriptions and Pin Information Summary sections.

— Updated BGA package to ucBGA.

— Changed SPI_CSN to SPI_SS_B.

— Corrected minor typo errors.

Ordering Information Updated iCE40 UltraLite Part Number Description section.

— Added shipment types.

— Updated BGA package to ucBGA.

Added Tape and Reel Quantity section.

Updated Ordering Part Numbers section.

— Added part numbers.

— Updated BGA package to ucBGA.

March 2015 1.1 All Document status changed from Preliminary to Final.

Introduction Updated General Description and Features sections. Changed the

LFOSC frequency value from 9.7 kHz to 10 kHz.

Architecture Updated On-Chip Oscillator section. Changed the LFOSC frequency

value from 9.7 kHz to 10 kHz.

DC and Switching

Characteristics

Updated Power-up Sequence section. Revised power-up sequence

description for 16-ball WLCSP. Added Power-up Sequence table.

Updated User I2C Specifications section. Added footnote 2.

Updated Internal Oscillators (HFOSC, LFOSC) section. Added and

revised values. Removed footnote.

Updated Maximum sysIO Buffer Performance section. Revised value for

LED I/O used as GPIO open drain.

Updated High Current LED, IR LED and Barcode LED Drives1 section.

Revised values.

January 2015 1.0 All Initial release.

Date Version Section Change Summary

Lattice Semiconductor Corporation 的 iCE40 UltraLite Family 规格书

信息

帮助

联系我们

关注我们