Greenlee Communications 的 7704SB, 06SB/7804SB, 06SB Manual 规格书

规格书反馈/错误

(:) GREENLEE® ATextron Company (—D «MIMI-ﬁll;

SERVICE MANUAL

Read and understand all of the instructions and

safety information in this manual before operating

or servicing this tool.

Quick Draw®

Hydraulic Punch Drivers

Serial Codes AHJ and YZ

7804SB / 7806SB Quick Draw®

7704SB / 7706SB Quick Draw® Flex

Quick Draw® Hydraulic Punch Drivers

Greenlee / A Textron Company 4455 Boeing Dr. • Rockford, IL 61109-2988 USA • 815-397-7070

Safety

Safety is essential in the use and maintenance of

Greenlee tools and equipment. This manual and any

markings on the tool provide information for avoiding

hazards and unsafe practices related to the use of this

tool. Observe all of the safety information provided.

Purpose of this Manual

This manual is intended to familiarize all personnel with

the safe service procedures for the following Greenlee

tools:

7704SB / 7706SB Serial Code AHJ

7804SB / 7806SB Serial Code YZ

Keep this manual available to all personnel.

Replacement manuals are available upon request at no

charge at www.greenlee.com.

Other Publications

Instruction Manual: 99947307

All specifications are nominal and may change as design

improvements occur. Greenlee Textron Inc. shall not be liable for

damages resulting from misapplication or misuse of its products.

Quick Draw is a registered trademark of Greenlee Textron Inc.

Loctite and 242 are registered trademarks of Loctite Corporation.

KEEP THIS MANUAL

Table of Contents

Safety ............................................................................ 2

Purpose of this Manual ................................................. 2

Other Publications ......................................................... 2

Important Safety Information ........................................ 3

Maintenance .................................................................. 4

Troubleshooting ............................................................. 5

Disassembly .................................................................. 6

Ball Seat Repair ............................................................. 6

Reassembly ................................................................... 7

Inspection and Adjustments .......................................... 7

Illustrations and Parts Lists ......................................8–11

7704SB / 7706SB ...................................................8–9

7804SB / 7806SB ...............................................10–11

Draw Studs and Accessories ...................................... 12

Quick Draw® Hydraulic Punch Drivers

Greenlee / A Textron Company 4455 Boeing Dr. • Rockford, IL 61109-2988 USA • 815-397-7070

IMPORTANT SAFETY INFORMATION

SAFETY

ALERT

SYMBOL

This symbol is used to call your attention to hazards

or unsafe practices which could result in an injury or

property damage. The signal word, defined below,

indicates the severity of the hazard. The message

after the signal word provides information for pre-

venting or avoiding the hazard.

Immediate hazards which, if not avoided, WILL result

in severe injury or death.

Hazards which, if not avoided, COULD result in

severe injury or death.

Hazards or unsafe practices which, if not avoided,

MAY result in injury or property damage.

Read and understand all of the

instructions and safety information

in this manual before operating or

servicing this tool. Refer also to the

instruction manual, which is listed

under “Other Publications.”

Failure to observe this warning could

result in severe injury or death.

Electric shock hazard:

Do not use this tool near live circuits.

This includes, but is not limited to, the

following:

• Near circuit breaker panels or fuse

boxes with energized circuits.

• Near junction boxes with energized

circuits.

Failure to observe this warning could

result in severe injury or death.

Wear eye protection when operating

or servicing this tool.

Failure to wear eye protection could

result in serious eye injury from flying

debris.

• Inspect tool for wear or damage. Replace any worn,

damaged, or missing components with Greenlee

replacement parts. A damaged or improperly

assembled tool can break and strike nearby

personnel with sufficient force to cause severe

injury or death.

• Inspect the punch, die, draw stud, and spacers for

wear or damage. Replace any worn or damaged

items with Greenlee replacement parts. Replace

any punches that have dull cutting surfaces.

Do not exceed the rated capacity of this tool.

Exceeding the rated capacity could cause a

component failure, which could throw broken parts

with great force.

Failure to observe this warning could result in severe

injury or death.

Do not operate the pump lever after the ram motion

stops. Continuing to operate the pump lever after the

ram motion stops will damage the driver and could

propel internal parts with great force, striking nearby

personnel.

Use this tool for the manufacturer’s intended purpose

only. Use other than that which is described in this

manual can result in injury or property damage.

Note: Keep all decals clean and legible, and replace

when necessary.

“A?

Quick Draw® Hydraulic Punch Drivers

Greenlee / A Textron Company 4455 Boeing Dr. • Rockford, IL 61109-2988 USA • 815-397-7070

Maintenance

Maintenance and repairs should be performed in a dust-

free area by qualified technicians.

This unit requires minimum maintenance because it

has a closed hydraulic system and all internal parts

are lubricated by the hydraulic fluid. Lubricate lever pins

lightly. Keep contaminants away from the ram and cyl-

inder. Store with the lever down and hydraulic pressure

released.

Adding Hydraulic Oil

1. Place the driver in a vise in a vertical position with

the handles up. Unscrew the reservoir handle and

remove the bladder plug. Open the release valve

knob to assure the ram is fully extended.

2. Fill the rubber bladder to the point of overflow with

Greenlee hydraulic oil.

3. Purge air from the system:

Pump the lever handle several times to remove air

from the pumping chamber. Close the release valve

knob and pump the lever handle until the ram com-

pletes its full travel. Repeat as necessary.

Note: Open the release valve knob slowly so the

ram extends slowly. Rapid return of oil and air may

cause the oil to overflow the rubber bladder.

If this procedure fails to remove air, remove the

bladder plug and open the release valve knob.

Place thumb over the plug hole in the bladder and

squeeze the bladder while pumping the lever handle

several times. Close the release valve knob and

pump the lever handle until the ram completes its

full travel. Repeat as necessary.

If this procedure does not remove air, remove the

plunger (24) and fill the plunger cavity with clean oil

as described in the “Reassembly” section of this

manual.

4. Fill the rubber bladder to the point of overflow and

replace the bladder plug. Wipe the bladder clean of

excess oil and reassemble the reservoir handle.

Release Valve Knob

Rubber Bladder

Bladder Plug

Reservoir Handle

Lever Handle

Oil Leaks

• Check for external oil leaks.

• Check that the release valve knob and stem are

closed tightly and seating properly.

• Remove the reservoir handle and check for oil leaks

around the rubber bladder and bladder plug.

Quick Draw® Hydraulic Punch Drivers

Greenlee / A Textron Company 4455 Boeing Dr. • Rockford, IL 61109-2988 USA • 815-397-7070

Troubleshooting

Problem Probable Cause Probable Remedy

Does not punch hole. Improper assembly or use of punch,

die, or accessories.

Refer to “Operation” and “Capacity

and Draw Stud Selection Guide” in

the Instruction Manual.

Low oil level. Refer to “Adding Hydraulic Oil” in

the “Maintenance” section.

Requires excessive lever force. Improper assembly or use of punch,

die, or accessories.

Refer to “Operation” and “Capacity

and Draw Stud Selection Guide” in

the Instruction Manual.

Material being punched is too thick

or too hard.

Refer to “Capacity and Draw Stud

Selection Guide” in the Instruction

Manual.

Pump does not build pressure. Air in system. Refer to step 3 of “Adding Hydraulic

Oil” in the “Maintenance” section.

Excessive number of strokes are

required to punch hole.

Inoperative intake check valve. Refer to “Intake Check Valve”

inspection in the “Inspection and

Adjustments” section.

Inoperative discharge check valve. Refer to “Discharge Check Valve”

inspection in the “Inspection and

Adjustments” section.

Leaking release valve. Refer to “Release Valve” inspection

in the “Inspection and Adjustments”

section.

Damaged piston, piston extension,

pump plunger seals, or mating

surfaces.

Refer to “Maintenance,” cylinder and

pump block sections.

Clogged filter. Clean or replace filter (31).

Does not return piston. Weak or damaged return spring;

excess oil in unit.

Refer to “Ram Travel Inspection” in

the “Inspection and Adjustments”

section.

External oil leaks. Damaged piston, piston extension,

pump plunger seals, or mating

surfaces.

Refer to “Maintenance,” cylinder and

pump block sections.

Damaged release valve stem seal. Refer to “Release Valve” inspection

in the “Inspection and Adjustments”

section.

AWARNING

Quick Draw® Hydraulic Punch Drivers

Greenlee / A Textron Company 4455 Boeing Dr. • Rockford, IL 61109-2988 USA • 815-397-7070

Disassembly

1. Remove reservoir handle (1), and bladder plug (20);

drain oil from the rubber bladder (29).

2. Remove O-ring retainer (35) and the rubber bladder

(29). Remove retaining rings (21) from one end of

both handle pins (30) and disassemble handle pins

and lever handle (2).

3. Grasp plunger (24) with pliers; pull and twist to

remove. Loosen set screw (12) from release valve

knob (27); remove knob. Unscrew release valve

stem (28) to remove from pump block (5). Ball (32) is

also accessible.

4. Loosen set screw (12) from cylinder (4) and

unscrew cylinder from pump block (5).

5. Remove compression spring (7), retaining plate (22)

and ram coupler (26). Spring (23) and ball (37) can

also be removed.

6. Screw a draw stud into end of ram (6); push the ram

out of the cylinder (4).

7. Remove filter (31). Remove seat (3) and ball (32).

Spring (13) will also be accessible.

You have now disassembled the punch driver.

Thoroughly clean all parts and inspect the three ball

seats (intake, discharge and release valve stem) for

nicks, scratches, or other damage.

Ball Seat Repair

Re-seating

Minor seat imperfections may be corrected by

re-seating. Use a soft brass rod and hammer to tap

the ball against its seat.

Wear eye protection when operating

or servicing this tool.

Failure to wear eye protection could

result in serious eye injury from flying

debris.

Re-drilling

Badly worn or damaged seats may be reworked by

re-drilling and then re-seating.

The pump block is manufactured with seats of 118°,

the standard drill point angle. Use standard drills for

re-drilling.

• To re-drill the 3/16" ball seat for release valve stem

(28): Use an “I” drill and a 9/64" diameter reamer.

• To re-drill the 7/32" ball seat for the discharge check:

Use an “I” drill and a 5/32" diameter reamer.

• To re-drill the 3/16" ball seat for the intake check:

Use a 1/4" drill and a 1/8" diameter reamer.

When drilling, remove a minimum of material to obtain

maximum seat life. Re-seat the balls before reassembly.

5/32" Ream

Discharge

Check

9/64" Ream

Intake

Check

“I” Drill

“B” Drill

Std. Drill

Acceptable

Release

Valve

Stem

Quick Draw® Hydraulic Punch Drivers

Greenlee / A Textron Company 4455 Boeing Dr. • Rockford, IL 61109-2988 USA • 815-397-7070

Reassembly

Reassembly is done in reverse sequence of

disassembly.

1. Use one of the following repair kits to replace all

O-ring seals, balls, and springs:

• 7704SB / 7706SB: Repair kit 501 0477.2

• 7804SB / 7806SB: Repair kit 503 7161.4

2. Inspect drilled oil passage in ram (6); be sure this

passage is not blocked.

3. Before reinserting ram (6) in cylinder (4), lightly coat

O-ring seals and bores of the cylinder with clean

hydraulic oil.

4. Coat discharge check spring (23) with petroleum gel

and insert it into the counter bore of the ram coupler

(26).

5. Fill plunger bore in pump block (5) with clean oil.

Then coat plunger O-ring seals with clean oil, and

reinsert in the pump block with release valve knob

(27) closed.

6. Fill unit with clean oil and purge air. Refer to “Adding

Hydraulic Oil” in the “Maintenance” section of this

manual.

Inspection and Adjustments

After reassembly, check the following:

Ram Travel Inspection

Ram Extended

With the draw stud removed and release valve knob

open, observe whether end of ram (6) is flush to 1/64"

(0.396 mm) below the end of cylinder (4). If it is not, the

rubber bladder (29) contains too much oil.

To remove excess oil:

1. Remove reservoir handle (1) and bladder plug (20).

2. Slowly open release valve knob (27); excess oil

should come out of the rubber bladder and the ram

should move to become flush to 1/64" (0.396 mm)

below the end of cylinder (4).

3. If excess oil does not come out, replace the

compression spring (7).

Ram Retracted

Measure ram travel distance (difference between ram

completely extended and completely retracted). Adjust

cylinder (4) so travel distance is 0.830" (21.1 mm) to

0.930" (23.6 mm). Tighten set screw (12).

33967

Adapter Set Screw

(12)

Piston

Travel

Rotate cylinder

to make adjustment.

.930"

.830"

(23.6 mm)

(21.1 mm)

Pump Section Inspection

Intake Check Valve

Close the release valve knob and operate lever

handle (2) until ram (6) bottoms and handle

resistance increases.

• If the ram bottoms in 30 strokes or less, the intake

check valve is operating properly.

• More than 30 strokes indicates an intake check leak.

Re-seat, re-drill, or replace the intake check seat.

Discharge Check Valve

If the lever handle (2) returns to the raised position

by itself, the discharge check valve is leaking.

Re-seat or re-drill the discharge check seat and replace

the discharge compression spring (23).

Release Valve

Pump the handle until the ram bottoms. Gently apply

and maintain additional force on lever handle (2). If the

lever handle remains solid, the release valve ball (32)

is operating properly. If the lever handle (2) goes down

slowly, the release valve is leaking. Re-seat or re-drill the

release valve stem seat and replace O-ring (33).

Quick Draw® Hydraulic Punch Drivers

Greenlee / A Textron Company 4455 Boeing Dr. • Rockford, IL 61109-2988 USA • 815-397-7070

Illustration—7704SB / 7706SB

33 33

33 36

14 15

3232

Repair Kits

50371606 Release Valve Unit Repair Kit

includes items keyed in black circles

(12, 16, 27, 28, 32, one of 33, 34)

50104772 Hydraulic Repair Kit

includes items keyed in black squares

(3, 8–11, 13–15, 21, 23, 31–37)

Quick Draw® Hydraulic Punch Drivers

Greenlee / A Textron Company 4455 Boeing Dr. • Rockford, IL 61109-2988 USA • 815-397-7070

Parts List—7704SB / 7706SB

Key Part No. Description Qty

1 50368893 Handle, reservoir ....................................................................................... 1

2 50368877 Handle, pump ........................................................................................... 1

3 50368907 Seat, inlet check........................................................................................ 1

4 50342711 Cylinder, hydraulic ..................................................................................... 1

5 50103903 Block weld assembly, pump ..................................................................... 1

6 50103849 Ram ........................................................................................................... 1

7 50342720 Spring, compression, 1.07 x 1.37 x 3.18 .................................................. 1

8 90538471 Backup ring, spiral, 1.00 x 1.24 x .027 ..................................................... 1

9 90513169 O-ring, 1.50 x 1.75 x .125 nitrile ................................................................ 1

10 90538498 Backup ring, spiral, 1.50 x 1.74 x .027 ..................................................... 1

11 90513304 O-ring, 1.00 x 1.25 x .125 nitrile ................................................................ 1

12 90552814 Screw, set #8-32 x .312 cup point ............................................................ 1

13 50342878 Spring ........................................................................................................ 1

14 90551214 Backup ring, spiral, .373 x .479 x .056 ..................................................... 1

15 90501683 O-ring, .364 x .500 x .068 nitrile ................................................................ 1

16 50318780 Decal, punch release ................................................................................. 1

18 90511301 O-ring, 1.50 x 1.62 x .062 nitrile ................................................................ 1

19 50232584 Grip, rubber ............................................................................................... 1

20 50324888 Plug, bladder ............................................................................................. 1

21 90541863 Retaining ring, .217 Truarc ........................................................................ 4

22 50103881 Retainer, coupler ....................................................................................... 1

23 90538455 Spring, compression, .152 x .180 x .380 .................................................. 1

24 50377159 Plunger ...................................................................................................... 1

26 50103865 Coupler, ram .............................................................................................. 1

27 50368869 Knob, release valve ................................................................................... 1

28 50368931 Stem, release valve ................................................................................... 1

29 50342690 Bladder, rubber ......................................................................................... 1

30 50377140 Pin, handle ................................................................................................ 2

31 52059251 Filter, oil ..................................................................................................... 1

32 90506782 Ball, steel, .187 diameter .......................................................................... 2

33 90538544 O-ring, .250 x .375 x .062 ......................................................................... 2

34 90504585 Pin, roll, .125 x .375 .................................................................................. 1

35 90503767 O-ring, 1.125 x 1.375 x .12 nitrile .............................................................. 1

36 90542304 Backup ring, spiral, .265 x .318 x .050 ..................................................... 1

37 90504526 Ball, steel, .218 diameter .......................................................................... 1

38 50368940 Cap, reservoir handle ................................................................................ 1

39 50103920 Hose .......................................................................................................... 1

40 50103873 Retainer, spring ......................................................................................... 1

41 90541421 Ring, retaining ........................................................................................... 1

42 50103938 Cover, hose ............................................................................................... 1

43 50015923 Decal, identification ................................................................................... 1

Quick Draw® Hydraulic Punch Drivers

Greenlee / A Textron Company 4455 Boeing Dr. • Rockford, IL 61109-2988 USA • 815-397-7070

Illustration—7804SB / 7806SB

534

Repair Kits

50371606 Release Valve Unit Repair Kit

includes items keyed in black circles

(12, 16, 27, 28, 32, one of 33, 34)

50371614 Hydraulic Repair Kit

includes items keyed in black squares

(3, 8–11, 13–15, 18, 21, 23, 31–37)

Quick Draw® Hydraulic Punch Drivers

Greenlee / A Textron Company 4455 Boeing Dr. • Rockford, IL 61109-2988 USA • 815-397-7070

Parts List—7804SB / 7806SB

Key Part No. Description Qty

1 50368893 Handle, reservoir ....................................................................................... 1

2 50368877 Handle, pump ........................................................................................... 1

3 50368907 Seat, inlet check........................................................................................ 1

4 50342711 Cylinder, hydraulic ..................................................................................... 1

5 50369008 Block, pump .............................................................................................. 1

6 50368966 Ram ........................................................................................................... 1

7 50342720 Spring, compression, 1.07 x 1.37 x 3.18 .................................................. 1

8 90538471 Backup ring, spiral, 1.00 x 1.24 x .027 ..................................................... 1

9 90513169 O-ring, 1.50 x 1.75 x .125 nitrile ................................................................ 1

10 90538498 Backup ring, spiral, 1.50 x 1.74 x .027 ..................................................... 1

11 90513304 O-ring, 1.00 x 1.25 x .125 nitrile ................................................................ 1

12 90510321 Screw, set, #8-32 x .187 socket cup ........................................................ 2

13 50342878 Spring ........................................................................................................ 1

14 90551214 Backup ring, spiral, .373 x .479 x .056 ..................................................... 2

15 90501683 O-ring, .364 x .500 x .068 nitrile ................................................................ 2

16 50318780 Decal, punch release ................................................................................. 1

18 90511301 O-ring, 1.50 x 1.62 x .062 nitrile ................................................................ 1

19 50232584 Grip, rubber ............................................................................................... 1

20 50324888 Plug, bladder ............................................................................................. 1

21 90541863 Retaining ring, .217 Truarc ........................................................................ 4

22 50368923 Plate, retaining .......................................................................................... 1

23 90538455 Spring, compression, .152 x .180 x .380 .................................................. 1

24 50377159 Plunger ...................................................................................................... 1

26 50368915 Coupler, ram .............................................................................................. 1