28015 规格书

规格书反馈/错误

P/‘PAL; X E Start Pu‘se _n_ a e J—L Echo Twme Pu‘se www auax com

Web Site: www.parallax.com

Forums: forums.parallax.com

Sales: sales@parallax.com

Technical: support@parallax.com

Office: (916) 624-8333

Fax: (916) 624-8003

Sales: (888) 512-1024

Tech Support: (888) 997-8267

PING))) Ultrasonic Distance Sensor (#28015)

The Parallax PING)))™ ultrasonic distance sensor provides precise, non-contact distance measurements

from about 2 cm (0.8 inches) to 3 meters (3.3 yards). It is very easy to connect to microcontrollers such

as the BASIC Stamp®, Propeller chip, or Arduino, requiring only one I/O pin.

The PING))) sensor works by transmitting an ultrasonic (well above human hearing range) burst and

providing an output pulse that corresponds to the time required for the burst echo to return to the

sensor. By measuring the echo pulse width, the distance to target can easily be calculated.

Features

 Range: 2 cm to 3 m (0.8 in to 3.3 yd)

 Burst indicator LED shows sensor

activity

 Bidirectional TTL pulse interface on a

single I/O pin can communicate with 5 V

TTL or 3.3 V CMOS microcontrollers

 Input trigger: positive TTL pulse, 2 µs

min, 5 µs typ.

 Echo pulse: positive TTL pulse, 115 µs

minimum to 18.5 ms maximum.

 RoHS Compliant

Key Specifications

 Supply voltage: +5 VDC

 Supply current: 30 mA typ; 35 mA max

 Communication: Positive TTL pulse

 Package: 3-pin SIP, 0.1” spacing

(ground, power, signal)

 Operating temperature: 0 – 70° C.

 Size: 22 mm H x 46 mm W x 16 mm D

(0.84 in x 1.8 in x 0.6 in)

 Weight: 9 g (0.32 oz)

Pin Definitions

GND Ground (Vss)

5 V 5 VDC (Vdd)

SIG Signal (I/O pin)

The PING))) sensor has a male 3-pin header used to supply

ground, power (+5 VDC) and signal. The header may be plugged

into a directly into solderless breadboard, or into a standard 3-

wire extension cable (Parallax part #800-00120).

<— 18"(457mm)="" —=""> E ‘25“ 4— 164“(417mm) <— 17‘(43="" 2mm)="" —="">1 mm“) |‘_ 64‘ (16 3mm) 6“ WWW Davallax 00m 74" (21 3mm) (‘8 8mm) (15 3mm) 0 ©2005 - . ¢ + P f 7 (2 5mm) —>1 [4— ->| l4— 1"(2 5mm) f km 7» + Mm (Homer; 5v SIG pin Sonar TX

Dimensions

Communication Protocol

The PING))) sensor detects objects by emitting a short ultrasonic burst and then "listening" for the echo.

Under control of a host microcontroller (trigger pulse), the sensor emits a short 40 kHz (ultrasonic) burst.

This burst travels through the air, hits an object and then bounces back to the sensor. The PING)))

sensor provides an output pulse to the host that will terminate when the echo is detected, hence the

width of this pulse corresponds to the distance to the target.

Host Device Input Trigger Pulse tOUT 2 µs (min), 5 µs typical

PING)))

Sensor Echo Holdoff tHOLDOFF 750 µs

Burst Frequency tBURST 200 µs @ 40 kHz

Echo Return Pulse Minimum tIN-MIN 115 µs

Echo Return Pulse Maximum tIN-MAX 18.5 ms

Delay before next measurement 200 µs

omen «45" too sman (ApprOX) k— >3.3m —>

Practical Considerations for Use

Object Positioning

The PING))) sensor cannot accurately measure the distance to an object that: a) is more than 3 meters

away, b) that has its reflective surface at a shallow angle so that sound will not be reflected back towards

the sensor, or c) is too small to reflect enough sound back to the sensor. In addition, if your PING)))

sensor is mounted low on your device, you may detect sound reflecting off of the floor.

a. b. c.

Target Object Material

In addition, objects that absorb sound or have a soft or irregular surface, such as a stuffed animal, may

not reflect enough sound to be detected accurately. The PING))) sensor will detect the surface of water,

however it is not rated for outdoor use or continual use in a wet environment. Condensation on its

transducers may affect performance and lifespan of the device.

Air Temperature

Temperature has an effect on the speed of sound in air that is measurable by the PING))) sensor. If the

temperature (°C) is known, the formula is:



m/sT0.6331.5C Cair 

The percent error over the sensor’s operating range of 0 to 70 ° C is significant, in the magnitude of 11

to 12 percent. The use of conversion constants to account for air temperature may be incorporated into

your program (as is the case in the example BS2 program given in the Example Programs section below).

Percent error and conversion constant calculations are introduced in Chapter 2 of

Smart Sensors and

Applications

, a Stamps in Class text available for download from the 28029 product page at

www.parallax.com.

Test Data

The test data on the following pages is based on the PING))) sensor, tested in the Parallax lab, while

connected to a BASIC Stamp microcontroller module. The test surface was a linoleum floor, so the

sensor was elevated to minimize floor reflections in the data. All tests were conducted at room

temperature, indoors, in a protected environment. The target was always centered at the same elevation

as the PING))) sensor.

Test 1

Sensor Elevation: 40 in. (101.6 cm)

Target: 3.5 in. (8.9 cm) diameter cylinder, 4 ft. (121.9 cm) tall – vertical orientation

10° 20° 30" 40“ 50° 60" 70" so“ 90" 10' 10° 20° 30“ 40" 50° 60° 70° 50“ 90° 10‘ V?“

Test 2

Sensor Elevation: 40 in. (101.6 cm)

Target: 12 in. x 12 in. (30.5 cm x 30.5 cm) cardboard, mounted on 1 in. (2.5 cm) pole

Target positioned parallel to backplane of sensor

zams W wwwpayanaxmm O Extension Cable and Port Cautions for the Board of Education 1514 Vdd 1312

Example Programs

BASIC Stamp 2

This circuit allows you to quickly connect your PING))) sensor to a BASIC Stamp® 2 via the Board of

Education® breadboard area. The PING))) module’s GND pin connects to Vss, the 5 V pin connects to

Vdd, and the SIG pin connects to I/O pin P15. This circuit will work with the example BASIC Stamp

program listed below.

Extension Cable and Port Cautions for the Board of Education

If you are connecting your PING))) sensor to a Board of Education platform using an extension cable,

follow these steps:

1. When plugging the cable onto the PING))) sensor, connect Black to GND, Red to 5 V, and White

to SIG.

2. Check to see if your Board of Education servo ports have a jumper, as shown at right.

3. If your Board of Education servo ports have a jumper, set it to Vdd as shown. Then plug the

cable into the port, matching the wire color to the labels next to the port.

4. If your Board of Education servo ports do not have a jumper, do not use them with the

PING))) sensor. These ports only provide Vin, not Vdd, and this may damage your PING)))

sensor. Go to the next step.

5. Connect the cable directly to the breadboard with a 3-pin header as shown above. Then, use

jumper wires to connect Black to Vss, Red to Vdd, and White to I/O pin P15.

Board of Education Servo Port Jumper, Set to Vdd

Example Program. P gMeasureCmAndl n.bsz th BASIC Stamp Debug Termina‘. The example program p www.9aral‘ax.com. The BASIC Stamp Edwtor softw f ad from www.gara‘\ax.com[baswcstampsoftware

Example Program: PingMeasureCmAndIn.bs2

This program for the BASIC Stamp 2 displays distance measurements in both inches and centimeters in

the BASIC Stamp Debug Terminal. The example program can be downloaded from the 28015 product

page at www.parallax.com. The BASIC Stamp Editor software, which includes the Debug Terminal, is a

free download from www.parallax.com/basicstampsoftware.

' Smart Sensors and Applications - PingMeasureCmAndIn.bs2

' Measure distance with Ping))) sensor and display in both in & cm

' {$STAMP BS2}

' {$PBASIC 2.5}

' Conversion constants for room temperature measurements.

CmConstant CON 2260

InConstant CON 890

cmDistance VAR Word

inDistance VAR Word

time VAR Word

PULSOUT 15, 5

PULSIN 15, 1, time

cmDistance = cmConstant ** time

inDistance = inConstant ** time

DEBUG HOME, DEC3 cmDistance, " cm"

DEBUG CR, DEC3 inDistance, " in"

PAUSE 100

LOOP

vtv$tv$vv$vv$vt$vt$vv$tv$vvivvivvivt$vt ' Huthori Ehrls Savage & Jeff Martln ' vtv$tv$vv$vv$vt$vt$vv$tv$vvivvivvivt$vt uans of Klme or distance. Each method requlres one parameter, Pin, that 15 the 1/0 pin that r44‘44‘44‘44‘44‘44‘1 |\ I | PINGJJ) | I \I Remember PING))) Requires L44‘44r44‘r4‘4r‘44‘J v1‘1 - Updated @3/2ﬂ/2ﬂﬂ7 to change SIG reslstor from lﬂK to 1K DUN diraEPln]~~ ' Make Pin Uutput diraEPln]~ ' Make I/U Pin Input waltpquﬂ, |< pin,="" e)="" '="" wait="" for="" pin="" to="" go="" loh="" microseconds="" ::="" (iikcntl="" -="" cntz)="" (clkfreq="" liﬂﬂﬂiﬂﬂﬂ))="">> 1 ' Return Time 1n us "Measure object distance 1n 1nches

Propeller Microcontroller

{{

***************************************

* Ping))) Object V1.1 *

* Author: Chris Savage & Jeff Martin *

* Started: 05-08-2006 *

***************************************

Interface to Ping))) sensor and measure its ultrasonic travel time. Measurements can be in

units of time or distance. Each method requires one parameter, Pin, that is the I/O pin that

is connected to the Ping)))'s signal line.

┌───────────────────┐

│┌───┐ ┌───┐│ Connection To Propeller

││ ‣ │ PING))) │ ‣ ││ Remember PING))) Requires

│└───┘ └───┘│ +5V Power Supply

│ GND +5V SIG │

└─────┬───┬───┬─────┘

│ │  1K

 └┘ └ Pin

--------------------------REVISION HISTORY--------------------------

v1.1 - Updated 03/20/2007 to change SIG resistor from 10K to 1K

}}

CON

TO_IN = 73_746 ' Inches

TO_CM = 29_034 ' Centimeters

PUB Ticks(Pin) : Microseconds | cnt1, cnt2

''Return Ping)))'s one-way ultrasonic travel time in microseconds

outa[Pin]~ ' Clear I/O Pin

dira[Pin]~~ ' Make Pin Output

outa[Pin]~~ ' Set I/O Pin

outa[Pin]~ ' Clear I/O Pin (> 2 μs pulse)

dira[Pin]~ ' Make I/O Pin Input

waitpne(0, |< Pin, 0) ' Wait For Pin To Go HIGH

cnt1 := cnt ' Store Current Counter Value

waitpeq(0, |< Pin, 0) ' Wait For Pin To Go LOW

cnt2 := cnt ' Store New Counter Value

Microseconds := (||(cnt1 - cnt2) / (clkfreq / 1_000_000)) >> 1 ' Return Time in μs

PUB Inches(Pin) : Distance

''Measure object distance in inches

Distance := Ticks(Pin) * 1_000 / TO_IN ' Distance In Inches

PUB Centimeters(Pin) : Distance

''Measure object distance in centimeters

Distance := Millimeters(Pin) / 10 ' Distance In Centimeters

PUB Millimeters(Pin) : Distance

''Measure object distance in millimeters

Distance := Ticks(Pin) * 10_000 / TO_CM ' Distance In Millimeters

object is used in an example p asurements. The complete http [lobex parallax com. www paralla comlgrogellertool ds and links to VldeO www garallax om

The ping.spin object is used in an example project with the Parallax 4 x 20 Serial LCD (#27979) to

display distance measurements. The complete Project Archive can be downloaded from the Propeller

Object Exchange at http://obex.parallax.com. The Propeller Tool software can be downloaded from

www.parallax.com/propellertool.

───────────────────────────────────────

Parallax Propeller Chip Project Archive

───────────────────────────────────────

Project : "ping_demo"

Archived : Tuesday, December 18, 2007 at 3:29:46 PM

Tool : Propeller Tool version 1.05.8

ping_demo.spin

│

├──Debug_Lcd.spin

│ │

│ ├──Serial_Lcd.spin

│ │ │

│ │ └──Simple_Serial.spin

│ │

│ └──Simple_Numbers.spin

│

└──ping.spin

Reources and Downloads

For additional example code downloads and links to videos, tutorials and robotics projects that use the

Ping))) Ultrasonic Distance Sensor, visit www.parallax.com and search “28015.”

Product Change Notice

Rev A: original release

Rev B: resonator added to the SX-28 co-processor circuit. No changes to functionality

Rev C: SX-28 co-processor changed to PIC16F57. No changes to functionality.

Revision History

Version 2.0: Added revision history. Removed Javelin Stamp examples. Added URLs for programming

software. Added Product Change Notice section with PCB revision information.

28015 规格书

信息

帮助

联系我们

关注我们