AT88SC0x04,808CA Datasheet by Microchip Technology

View All Related Products | Download PDF Datasheet
Atmet
AT88SC0104CA, AT88SC0404CA
AT88SC0204CA, AT88SC0808CA
Atmel CryptoMemory Low Density Full Specification
DATASHEET
Features
One of a Family of Devices with User Memories from 1-Kbit to 8-Kbit
EEPROM User Memory
Four or Eight Zones
Self-timed Write Cycles
Single Byte or Multiple Byte Page Write Modes
Programmable Access Rights for Each Zone
2-Kbit Configuration Zone
37-byte OTP Area for User-Defined Codes
160-byte Area for User-Defined Keys and Passwords
High Security Features
64-bit Mutual Authentication Protocol (Under License of ELVA)
Cryptographic Message Authentication Codes (MAC)
Stream Encryption
Four Key Sets for Authentication and Encryption
Eight Sets of Two 24-bit Passwords
Anti-tearing Function
Voltage and Frequency Monitor
Embedded Application Features
Low-voltage Supply: 2.7V to 3.6V
Secure Nonvolatile Storage for Sensitive System or User Information
2-Wire Serial Interface (TWI, 5V Compatible)
1MHz Compatibility for Fast Operation
Standard 8-lead Plastic Packages, Green Compliant (Exceeds RoHS)
Same Pinout as 2-wire Serial EEPROMs
Smart Card Features
ISO 7816 Class B (3V) Operation
ISO 7816-3 Asynchronous T = 0 Protocol (Gemplus® Patent)
Multiple Zones, Key Sets, and Passwords for Multi-Application Use
Synchronous 2-Wire Serial Interface for Faster Device Initialization
Programmable 8-byte Answer-To-Reset (ATR) Register
ISO 7816-2 Compliant Modules
High Reliability
Endurance: 100,000 Cycles
Data Retention: 10 Years
ESD Protection: 2,000V
Atmel-8664I-CryptoMem-Low-Density-Full-Specification-Datasheet_072015
AtmeL
AT88SC0104CA/0204CA/0404CA/0808CA [Datasheet]
Atmel-8664I-CryptoMem-Low-Density-Full-Specification-Datasheet_072015
2
Table of Contents
1. Pin Configuration and Package Information .................................................... 4
1.1 Pin Configuration ................................................................................................ 4
1.2 Package Information ........................................................................................... 4
2. Description ....................................................................................................... 5
2.1 Atmel AT88SCxxxxC Family of Products Differences ......................................... 5
2.2 Embedded Applications ...................................................................................... 5
2.3 Smart Card Applications ..................................................................................... 5
2.4 Scope ............................................................................................................... 5
3. Block Diagram ................................................................................................. 6
4. Pin Description ................................................................................................ 7
4.1 Supply Voltage (VCC) .......................................................................................... 7
4.2 Clock (SCL/CLK)................................................................................................. 7
4.3 Serial Data (SDA/IO) ........................................................................................... 7
4.4 Reset (RST) ........................................................................................................ 7
5. Configuration and User Zone Description ....................................................... 8
5.1 Detailed Description ............................................................................................ 8
5.2 Control Logic ....................................................................................................... 8
5.3 Configuration Memory ......................................................................................... 8
5.4 User Memory .................................................................................................... 11
6. Communication Security Modes .................................................................... 14
6.1 Security Operations .......................................................................................... 14
6.2 Data Protection Features .................................................................................. 17
6.3 Configuration Memory Values ........................................................................... 18
6.4 Security Fuses .................................................................................................. 23
7. Protocol Selection.......................................................................................... 24
7.1 Synchronous Mode for Embedded Applications ............................................... 24
7.2 Asynchronous Mode for Smart Card Applications ............................................ 25
8. Synchronous Protocol ................................................................................... 26
8.1 Start-up Sequence ............................................................................................ 26
8.2 Command Set ................................................................................................... 27
8.3 Command Format ............................................................................................. 28
8.4 Acknowledge Polling ......................................................................................... 29
8.5 Device Addressing ............................................................................................ 30
8.6 TWI Command Descriptions ............................................................................. 30
8.7 Write User Zone: $B0 ....................................................................................... 31
8.8 Random Read: $B1 .......................................................................................... 32
8.9 Read User Zone: $B2 ....................................................................................... 33
8.10 System Write: $B4 ............................................................................................ 34
8.11 System Read: $B6 ............................................................................................ 36
8.12 Verify Crypto: $B8 ............................................................................................. 38
8.13 Verify Password: $BA ....................................................................................... 40
9. Initialization Example ..................................................................................... 41
9.1 Write Data to User Zones ................................................................................. 41
9.2 Unlock the Configuration Memory ..................................................................... 41
9.3 Write Data to the Configuration Memory ........................................................... 41
9.4 Set Security Fuses ............................................................................................ 41
Atmel
AT88SC0104CA/0204CA/0404CA/0808CA [Datasheet]
Atmel-8664I-CryptoMem-Low-Density-Full-Specification-Datasheet_072015
3
10. Asynchronous T=0 Protocol .......................................................................... 44
10.1 Character Format .............................................................................................. 44
10.2 Command format .............................................................................................. 44
10.3 Command Set ................................................................................................... 45
10.4 T=0 Command Descriptions ............................................................................. 47
10.5 Write User Zone: $B0 ....................................................................................... 47
10.6 Read User Zone: $B2 ....................................................................................... 48
10.7 System WRITE: $B4 ......................................................................................... 49
10.8 System READ: $B6 ........................................................................................... 51
10.9 Verify CRYPTO: $B8 ........................................................................................ 53
10.10 Verify Password: $BA ..................................................................................... 55
11. Initialization Example ..................................................................................... 56
11.1 Write Data to User Zones ................................................................................. 56
11.2 Unlock the Configuration Memory ..................................................................... 56
11.3 Write Data to the Configuration Memory ........................................................... 56
11.4 Set Security Fuses ............................................................................................ 56
12. Absolute Maximum Ratings ........................................................................... 59
12.1 DC and AC Characteristics ............................................................................... 59
12.2 Timing Diagrams for Synchronous Communications ........................................ 60
13. POR and Tamper Conditions ........................................................................ 63
13.1 Power On Reset (POR) Delay .......................................................................... 63
13.2 Tamper Detection ............................................................................................. 63
14. Ordering Information...................................................................................... 64
15. Package Marking Information ........................................................................ 65
15.1 AT88SC0104CA ............................................................................................... 65
15.2 AT88SC0204CA ............................................................................................... 66
15.3 AT88SC0404CA ............................................................................................... 67
15.4 AT88SC0808CA ............................................................................................... 68
Appendix A. Errata .............................................................................................. 69
A.1 Send Checksum Command in TWI Mode ......................................................... 69
Appendix B. Revision History .............................................................................. 70
3:3: 1111 EEEE EEC: jjjj CECE
AT88SC0104CA/0204CA/0404CA/0808CA [Datasheet]
Atmel-8664I-CryptoMem-Low-Density-Full-Specification-Datasheet_072015
4
1. Pin Configuration and Package Information
1.1 Pin Configuration
Table 1-1. Package Pin Configuration
Pad
Description
ISO Module
Contact
Standard
Package Pin
TSSOP
Mini-Map
VCC
Supply Voltage
C1
8
8
4
GND
Ground
C5
4
1
5
SCL/CLK
Serial Clock Input
C3
6
6
2
SDA/IO
Serial Data Input/Output
C7
5
3
7
RST
Reset Input
C2
NC
NC
NC
1.2 Package Information
Figure 1-1. Atmel CryptoMemory Packages
1
2
3
4
8
7
6
5
Smart Card Module
VCC = C1
RST = C2
SCL/CLK = C3
NC = C4
C5 = GND
C6 = NC
C7 = SDA/IO
C8 = NC
8-lead SOIC, PDIP
NC
NC
NC
GND
VCC
NC
SCL
SDA
8-lead TSSOP
NC
VCC
81
NC CN72 8-Lead TSSOP
NC
KLC63
GND
54
SDA
1
2
3
4
8
7
6
5
SDA
GND
CLK
VCC
8-lead Ultra Thin Mini-MAP (MLP 2x3)
Bottom View
NC
NC
NC
NC
Atmel
AT88SC0104CA/0204CA/0404CA/0808CA [Datasheet]
Atmel-8664I-CryptoMem-Low-Density-Full-Specification-Datasheet_072015
5
2. Description
The Atmel® AT88SCxxxxCA is a family of four high-performance secure memory devices providing 1Kbit to 8Kbits of user
memory with advanced built-in security and cryptographic features. The memory is divided into four or eight user zones each
of which may be individually set with different security access rights or used together to provide space for one or multiple data
files. A Configuration zone contains registers to define the security rights for each user zone and space for passwords and
secret keys used by the security logic of Atmel CryptoMemory®.
Through dynamic, symmetric-mutual authentication, data encryption, and the use of encrypted checksums, CryptoMemory
provides a secure place for storage of sensitive information within a system. With its tamper protection circuits, this information
remains safe even under attack.
CryptoMemory also provides high security, low cost and ease of implementation of host-client type systems without the need
for a microprocessor operating system. The embedded cryptographic engine provides for a dynamic, symmetric-mutual
authentication between the device and host, as well as performs stream encryption for all data and passwords exchanged
between the device and host. Up to four unique key sets may be used for these operations.
2.1 Atmel AT88SCxxxxC Family of Products Differences
The key differentiating feature of the AT88SCxxxxCA family of memory devices from AT88SCxxxxC family is support for
hardware implementation of the TWI read command. Support for this TWI hardware command allows for faster application
development and also permits greater device versatility. In addition, AT88SCxxxxCA offers a Random Read command,
whereby given a starting address, the user can clock unlimited number of bytes from the device up to the memory capacity.
Last but not least, the AT88SCxxxxCA family of devices specifically targets low-voltage and low-power applications.
2.2 Embedded Applications
A 2-Wire serial interface running at 1MHz is used for fast and efficient communications with up to 15 devices that may be
individually addressed. CryptoMemory is available in industry standard 8-lead packages with the same familiar pin layout as
2-Wire Serial EEPROMs supporting only the synchronous communications protocol.
Note: TSSOP pinout not the same.
2.3 Smart Card Applications
CryptoMemory offers the ability to communicate with virtually any smart card reader using the asynchronous T=0 protocol
defined in ISO 7816-3. All CryptoMemory devices in smart card module form will also communicate using a synchronous
2-Wire serial interface.
2.4 Scope
This CryptoMemory specification document includes all specifications for the standard, authentication, and encryption modes
of CryptoMemory operation.
AtmeL
AT88SC0104CA/0204CA/0404CA/0808CA [Datasheet]
Atmel-8664I-CryptoMem-Low-Density-Full-Specification-Datasheet_072015
6
3. Block Diagram
Figure 3-1. Block Diagram
Atmel
AT88SC0104CA/0204CA/0404CA/0808CA [Datasheet]
Atmel-8664I-CryptoMem-Low-Density-Full-Specification-Datasheet_072015
7
4. Pin Description
4.1 Supply Voltage (VCC)
The VCC input is a 2.7V to 3.6V positive voltage supplied by the host.
4.2 Clock (SCL/CLK)
In the asynchronous T=0 protocol, the SCL/CLK input is used to provide the device with a carrier frequency f. The nominal
length of one bit emitted on I/O is defined as an "Elementary Time Unit" (ETU) and is equal to 372/ f. When the synchronous
protocol is used, the SCL/CLK input is used to clock data in on the positive clock edge and clock data out on the negative
clock edge.
4.3 Serial Data (SDA/IO)
The SDA pin is bi-directional for serial data transfer. This pin is open-drain driven and may be wired with any number of other
open drain or open collector devices. An external pull up resistor should be connected between SDA and VCC, a nominal value
of 4.7KΩ may be used. The value of this resistor and the system capacitance loading the SDA bus will determine the rise time
of SDA. This rise time will determine the maximum frequency during read operations. Low value pull-up resistors will allow
higher frequency operations while drawing higher average power supply current.
4.4 Reset (RST)
CryptoMemory provides an ISO 7816-3 compliant asynchronous Answer-To-Reset (ATR) sequence. When the reset
sequence is activated, the device will output the data programmed into the 64-bit ATR register. When RST is low, all internal
logic, access rights, and write cycles are in reset, except the asynchronous mode activation flag. A weak internal pull-up on the
RST input pad allows the device to be used in synchronous mode without bonding RST. For synchronous only smart card
applications, an external pull-up on RST is recommended to ensure synchronous operation under any system timings or
conditions. CryptoMemory does not support a synchronous ATR sequence. The RST input is not available in the plastic
package options for CryptoMemory.
Figure 4-1. Connection Diagram
Note: While the Atmel CryptoMemory AT88SCXXXXCA is a low-voltage device (2.7V to 3.6V), its I/O buffers are
designed for standard high-voltage applications (2.7V to 5.5V).
2.7v - 5.5v
2.7v - 3.6v
SDA
SCL
CryptoMemoryMicroprocessor
AtmeL
AT88SC0104CA/0204CA/0404CA/0808CA [Datasheet]
Atmel-8664I-CryptoMem-Low-Density-Full-Specification-Datasheet_072015
8
5. Configuration and User Zone Description
5.1 Detailed Description
To enable the security features of CryptoMemory, personalize the device by setting up registers and loading appropriate
passwords and keys. This is accomplished though programming the Configuration zone of CryptoMemory using simple write
and read commands. To gain access to the Configuration zone, the secure code (Write 7 password) must be successfully
presented. After writing and verifying data in the Configuration zone, the security fuses must be blown to lock this information
in the device. For additional information on personalizing CryptoMemory, please see the examples in the protocol sections of
this specification.
5.2 Control Logic
Access to the user zones occurs only through the control logic built into the device. This logic is configurable through access
registers, key registers, and keys programmed into the configuration memory during device personalization. Also implemented
in the control logic is a cryptographic engine for performing the various higher-level security functions of the device.
5.3 Configuration Memory
The configuration memory consists of 2048 bits of EEPROM memory used for storing passwords, keys, codes, and defining
security levels to be used for each user zone. The control logic defines access rights to the configuration memory, and the
user may not alter these rights. The access rights include the ability to program certain portions of the configuration memory,
and then lock the data written through use of security fuses. The configuration memory for each CryptoMemory device is
identical with the exception of the number of access registers and password/key registers available. Devices with four user
zones have four sets of registers, and those with eight user zones, eight sets of registers. Unused memory space in the
register region becomes reserved to ensure other components of the configuration memory remain at the same address
location regardless of the number of user zones in a device.
Atmel 9
AT88SC0104CA/0204CA/0404CA/0808CA [Datasheet]
Atmel-8664I-CryptoMem-Low-Density-Full-Specification-Datasheet_072015
9
Table 5-1. Atmel AT88SC0104CA/0204CA/0404CA Configuration Memory
$0
$1
$2
$3
$4
$5
$6
$7
$00
Answer to Reset
Identification
$08
FAB Code
MTZ
Card Manufacturer Code
$10
Lot History Code
Read-Only
$18
DCR
Identification Number Nc
Access Control
$20
AR0
PR0
AR1
PR1
AR2
PR2
AR3
PR3
$28
Reserved
$30
$38
$40
Issuer Code
$48
$50
AAC0
Cryptogram C0
Cryptography
$58
Session Encryption Key S0
$60
AAC1
Cryptogram C1
$68
Session Encryption Key S1
$70
AAC2
Cryptogram C2
$78
Session Encryption Key S2
$80
AAC3
Cryptogram C3
$88
Session Encryption Key S3
$90
Secret Seed G0
Secret
$98
Secret Seed G1
$A0
Secret Seed G2
$A8
Secret Seed G3
$B0
PAC
Write 0
PAC
Read 0
Password
$B8
PAC
Write 1
PAC
Read 1
$C0
PAC
Write 2
PAC
Read 2
$C8
PAC
Write 3
PAC
Read 3
$D0
PAC
Write 4
PAC
Read 4
$D8
PAC
Write 5
PAC
Read 5
$E0
PAC
Write 6
PAC
Read 6
$E8
PAC
Write 7
PAC
Read 7
$F0
Reserved
Forbidden
$F8
AtmeL
AT88SC0104CA/0204CA/0404CA/0808CA [Datasheet]
Atmel-8664I-CryptoMem-Low-Density-Full-Specification-Datasheet_072015
10
Table 5-2. Atmel AT88SC0808CA Configuration Memory
$0
$1
$2
$3
$4
$5
$6
$7
$00
Answer to Reset
Identification
$08
FAB Code
MTZ
Card Manufacturer Code
$10
Lot History Code
Read-Only
$18
DCR
Identification Number Nc
Access Control
$20
AR0
PR0
AR1
PR1
AR2
PR2
AR3
PR3
$28
AR4
PR4
AR5
PR5
AR6
PR6
AR7
PR7
$30
Reserved
$38
$40
Issuer Code
$48
$50
AAC0
Cryptogram C0
Cryptography
$58
Session Encryption Key S0
$60
AAC1
Cryptogram C1
$68
Session Encryption Key S1
$70
AAC2
Cryptogram C2
$78
Session Encryption Key S2
$80
AAC3
Cryptogram C3
$88
Session Encryption Key S3
$90
Secret Seed G0
Secret
$98
Secret Seed G1
$A0
Secret Seed G2
$A8
Secret Seed G3
$B0
PAC
Write 0
PAC
Read 0
Password
$B8
PAC
Write 1
PAC
Read 1
$C0
PAC
Write 2
PAC
Read 2
$C8
PAC
Write 3
PAC
Read 3
$D0
PAC
Write 4
PAC
Read 4
$D8
PAC
Write 5
PAC
Read 5
$E0
PAC
Write 6
PAC
Read 6
$E8
PAC
Write 7
PAC
Read 7
$F0
Reserved
Forbidden
$F8
Atmel
AT88SC0104CA/0204CA/0404CA/0808CA [Datasheet]
Atmel-8664I-CryptoMem-Low-Density-Full-Specification-Datasheet_072015
11
5.4 User Memory
The EEPROM user memory is divided into four (AT88SC0104CA/0204CA/0404CA) or eight (AT88SC0808CA) user zones.
Multiple zones allow for the storage of different data types or files in different zones. Access to user zones is possible only
after meeting security requirements. The customer defines these security requirements in the Configuration zone during
device personalization. When the same security requirements define access to multiple zones, the zones effectively serve as
one large storage area albeit with the requirement to select each zone prior to access. User zone access is personalized by
customer via the access registers.
Table 5-3. Atmel AT88SC0104CA User Memory
Zone
$0
$1
$2
$3
$4
$5
$6
$7
User 0
$00
32 bytes
$18
User 1
$00
32 bytes
User 2
$00
32 bytes
$18
User 3
$00
32 bytes
$18
Note: Page size = 16 bytes
AT88SC0104CA/0204CA/0404CA/0808CA [Datasheet]
Atmel-8664I-CryptoMem-Low-Density-Full-Specification-Datasheet_072015
12
Table 5-4. Atmel AT88SC0204CA User Memory
Zone
$0
$1
$2
$3
$4
$5
$6
$7
User 0
$00
64 bytes
$38
User 1
$00
64 bytes
$38
User 2
$00
64 bytes
$38
User 3
$00
64 bytes
$38
Note: Page size = 16 bytes
AT88SC0104CA/0204CA/0404CA/0808CA [Datasheet]
Atmel-8664I-CryptoMem-Low-Density-Full-Specification-Datasheet_072015
13
Table 5-5. Atmel AT88SC0404CA User Memory
Zone
$0
$1
$2
$3
$4
$5
$6
$7
User 0
$00
128 bytes
$78
User 1
$00
128 bytes
$78
User 2
$00
128 bytes
$78
User 3
$00
128 bytes
$78
Note: Page size = 16 bytes
Table 5-6. Atmel AT88SC0808CA User Memory
Zone
$0
$1
$2
$3
$4
$5
$6
$7
User 0
$00
128 bytes
$78
User 1
User 6
$00
$78
User 7
$00
128 bytes
$78
Note: Page size = 16 bytes
aha) AtmeL
AT88SC0104CA/0204CA/0404CA/0808CA [Datasheet]
Atmel-8664I-CryptoMem-Low-Density-Full-Specification-Datasheet_072015
14
6. Communication Security Modes
Communication between the device and host operates in three basic modes:
Standard Mode Default mode for the device after power-up.
Authentication Mode Activated by a successful authentication sequence.
Encryption Mode Activated by a successful encryption activation following a successful authentication.
Data transferred to and from the device is handled per the following table.
Table 6-1. Communication Security Modes
Mode
Configuration Data
User Data
Passwords
Data Integrity Check
Standard/Password
Clear
Clear
Clear
MDC
Authentication
Clear
Clear
Encrypted
MAC
Encryption
Clear
Encrypted
Encrypted
MAC
Note: 1. Configuration data includes the entire configuration memory except the passwords:
MDC: Modification Detection Code
MAC: Message Authentication Code
6.1 Security Operations
6.1.1 Password Verification
The use of passwords protects read and write accesses to the user zones. Any one of eight password sets is available for
assignment to any user zone through configuration of access registers. CryptoMemory provides separate 24-bit passwords for
read and write operations. Read passwords grant only read accesses to zones under password protection, while write
passwords grant both read and write accesses. Successful presentation of any password renders the Verify Password
command active until the presentation of another password or device reset. Only one password may be active at a time.
Presenting incorrect passwords decrements the value of the corresponding password attempts counter (PAC). Decrementing
the PAC to $00 permanently disables the corresponding password and permanently renders the corresponding user zone(s)
under protection inaccessible. Operation in authentication or encryption modes requires encryption of passwords for all
password transactions.
Figure 6-1. Password Verification
Command/CommunicationsCryptoMemory Device
VERIFY Password
Allow Access
Host Logic
Send Password
encrypted if performed after
Mutual Authentication
Verify Password
{will
AT88SC0104CA/0204CA/0404CA/0808CA [Datasheet]
Atmel-8664I-CryptoMem-Low-Density-Full-Specification-Datasheet_072015
15
6.1.2 Authentication Protocol
The use of a mutual authentication protocol further protects access to user zones. Any one of four key sets is available for
assignment to any user zone through configuration of access registers. Each key set consists of a secret seed, a cryptogram,
and a session encryption key. A Verify Crypto command exists to allow the use of any one of the key sets to enter
authentication mode. Each successful entry into authentication mode renders the mode active for the current key set until the
next call to the Verify Crypto command or device reset. Only one key set may be active at anytime. Unsuccessful calls of the
Verify Crypto command exits authentication mode and decrements the value of the Authentication Attempts Counter (AAC)
register. Decrementing AAC to $00 permanently disables the corresponding key set and permanently renders the
corresponding user zone(s) under protection inaccessible.
Entry into authentication mode is a process through which the host and CryptoMemory device mutually authenticate one
another. First, the host generates a 64-bit random number, reads a current cryptogram, and identification information from the
device, and uses this information in conjunction with the corresponding secret seed to generate a 64-bit challenge for the
device. The host also generates a new cryptogram and session encryption key in the process. The host then sends the
challenge and random number to the device by calling the Verify Crypto command. The device utilizes the random number
from the host to generate its own challenge, new cryptogram, and session encryption key. It then compares the challenge to
the one from the host. If the challenges match, then the device declares the host authentic, overwrites its corresponding
current cryptogram and session encryption key with the new ones. To complete the mutual authentication, the host reads the
new cryptogram from the device and compares it with its new cryptogram. The new cryptogram from the device serves as a
challenge to the host. If the cryptograms match then the device is authentic. Only an authentic pair of host and device can
generate the same challenges and cryptograms. Activating mutual authentication requires the use of the verify authentication
variant of the Verify Crypto command (see Section 8.2, Command Set and Section 10.3, Command Set).
Figure 6-2. The Mutual Authentication Process
CryptoMemory Device
Device Info, Cryptogram
[Secret Seed]
Compute Challenge A
Verify Challenge A
Compute Challenge B
Compute Session Key
Allow Access
Host Logic
Read Device Info, Cryptogram
Compute Secret Seed
Generate Random Number
Compute Challenge A
Compute Challenge B
Compute Session Key
Read Challenge B
Verify Challenge B
Allow Access
Read Config Zone
Verify Authentication
Read Config Zone
Command/Communications
e‘lll iiii
AT88SC0104CA/0204CA/0404CA/0808CA [Datasheet]
Atmel-8664I-CryptoMem-Low-Density-Full-Specification-Datasheet_072015
16
6.1.3 Data Encryption
CryptoMemory allows the use of encryption between a host system and the CryptoMemory device to protect the confidentiality
of data during read-write accesses and verify password operations. To enable encryption, the host must generate a challenge
using the session encryption key generated from the authentication activation step. The host then needs to call the Verify
Crypto command again with the device still in active authentication mode. The session encryption key must belong to the
active authentication key set. The host may enable encryption at any time after which data content of communication between
host and device user zones becomes encrypted. If a user zone configuration in the access register requires encryption,
however, then the host must enter encryption mode and must encrypt all data content to and from the zone in the remainder of
the active encryption session in order to communicate with the zone. CryptoMemory does not encrypt system zone data
except for password and password attempt counters. Passwords and password attempt counters require encryption during
active authentication or encryption modes.
Each successful entry into encryption mode renders the mode active for the current key set until the next call to the Verify
Crypto command or device reset. Only one key set may be active at anytime. Unsuccessful calls of the Verify Crypto
command exits both encryption and authentication modes and decrements the value of the authentication attempts counter
(AAC) register. Decrementing AAC to $00 permanently disables the corresponding key set and permanently renders the
corresponding user zone(s) under protection inaccessible. Activating encryption is similar in process to activating
authentication with the exception that the session encryption key replaces the secret seed. The process uses the verify
encryption variant of the Verify Crypto command (see Section 8.2, Command Set and Section 10.3, Command Set.)
Figure 6-3. Encryption Activation Process from Active Authentication Mode
6.1.4 Encrypted Checksum (Message Authentication Code, MAC)
CryptoMemory implements a data validity check function in the form of an encrypted checksum. This checksum provides a
bi-directional data integrity check and data origin authentication capability in the form of a Message Authentication Code
(MAC): only the host/device that carried out a valid authentication is capable of computing a valid MAC. When writing data to
the CryptoMemory device in authentication or encryption communication modes, the host must send a valid checksum
immediately following the write command. If the checksum is invalid, the device rejects the write command and resets the
device security privileges. The host must reinitiate entry into authentication and, if applicable, encryption modes to continue.
The use of checksum is optional when reading data. Calls to the Read Checksum command resets device security so its use
is recommended only at the completion of all data read operations from the device.
CryptoMemory Device
Session Key, Cryptogram
Compute Challenge A
Verify Challenge A
Compute Challenge B
Enable Encryption
Host Logic
Session Key, Cryptogram
Generate Random Number
Compute Challenge A
Compute Challenge B
Read Challenge B
Verify Challenge B
Verify Encryption
Read Config Zone
Command/Communications
Atmel
AT88SC0104CA/0204CA/0404CA/0808CA [Datasheet]
Atmel-8664I-CryptoMem-Low-Density-Full-Specification-Datasheet_072015
17
6.2 Data Protection Features
Security operations control access to data stored in CryptoMemory. After gaining access, additional options exist to protect
data in the user memory.
6.2.1 Modify Forbidden
The Modify Forbidden option renders the user zone read-only by restricting all write operations to it. It is recommended to
program all required data in the user zone prior to enabling this option. Modify forbidden is available for any user zone and is
selectable by configuring appropriate access registers.
6.2.2 Program Only
The Program Only option constrains data bit modification to programming from Logic 1 to Logic 0 only. Data bits may never
change from Logic 0 to Logic 1. Program-only is available for any user zone and is selectable by configuring appropriate
access registers.
6.2.3 Write Lock
The Write Lock option provides ability to render individual bytes within a user zone read-only by restricting all write operations
to it. It operates on 8-byte page level whereby the lowest addressed byte of the page serves as the write access control byte
for that page. Table 6-2 shows the use of Write Lock for data at addresses $080 to $087. The byte at $080 controls write
access to bytes from $080 to $087.
Table 6-2. Write Lock Example
Address
$0
$1
$2
$3
$4
$5
$6
$7
$080
11011001
xxxx xxxx
xxxx xxxx
xxxx xxxx
xxxx xxxx
xxxx xxxx
xxxx xxxx
xxxx xxxx
Locked
Locked
Locked
The Write Lock option also applies to the access control byte for each page by writing its least significant (rightmost) bit to
Logic 0. Moreover, only logic modifications from Logic 1 to Logic 0 of the access control byte are permissible. Write Lock is
available for any user zone and is selectable by configuring appropriate access registers. Furthermore, configuring a user
zone with the Write Lock option restricts writing to that zone to a byte at a time. Attempts to write several bytes within a
command; results in writing only the first byte.
6.2.4 Anti-tearing (Power Loss Protection)
In the event of a power loss during a write cycle, the integrity of the device's stored data may be recovered. This function is
optional, and the host may choose to activate the anti-tearing function for any write to a user zone or Configuration zone by
use of the appropriate B4 System Write command. When anti-tearing is active, write commands will take longer to execute
since more write cycles are required. Additionally, the data written is limited to eight bytes.
Data is written first to a buffer zone in EEPROM instead of the intended destination address in the user zone or Configuration
zone, but with the same access conditions. If this write cycle is interrupted the original data remains intact in the user zone or
Configuration zone. The data is then written in the required memory location. If this second write cycle is interrupted the device
will automatically recover the data from the system buffer zone at the next power-up and write it to the intended destination
address.
In 2-Wire mode, the host is required to perform ACK polling for 36ms after write commands when anti-tearing is active. At
power-up, five clock cycles are required to check the anti-tearing flags. In the event the device needs to carry out the data
recovery process the host is required to perform ACK polling for 18ms.
AtmeL
AT88SC0104CA/0204CA/0404CA/0808CA [Datasheet]
Atmel-8664I-CryptoMem-Low-Density-Full-Specification-Datasheet_072015
18
6.3 Configuration Memory Values
This section describes each individual field in the configuration memory.
6.3.1 Default Values
Atmel programs certain fields of the system zone at the factory. The customer may elect to change the content of all of these
fields except for the lot history code field, which is permanently locked. Atmel programs the remainder of the fields, including
all of the configuration memory and user zones to ones prior to releasing the device from the factory. Table 6-3, “Factory
Programmed Fields,” summarizes device fields Atmel programs at the factory. A brief description of each field follows.
Table 6-3. Factory Programmed Fields
Device
ATR
FAB Code
Lot History Code
Write 7 Password
(Secure Code)
AT88SC0104CA
3B B2 11 00 10 80 00 01
10 10
Variable, Locked
DD 42 97
AT88SC0204CA
3B B2 11 00 10 80 00 02
20 20
Variable, Locked
E5 47 47
AT88SC0404CA
3B B2 11 00 10 80 00 04
40 40
Variable, Locked
60 57 34
AT88SC0808CA
3B B2 11 00 10 80 00 08
80 60
Variable, Locked
22 E8 3F
6.3.2 Answer To Reset (ATR)
This is an eight byte wide register with content that Atmel defines. This register is read/write accessible prior to blowing the
FAB fuse, but becomes read-only after blowing the fuse.
6.3.3 FAB Code
This field is a 16-bit wide register with content that Atmel defines. This field is read/write accessible prior to blowing the FAB
fuse, but becomes read-only after blowing the fuse.
6.3.4 Memory Test Zone (MTZ)
This field is a 16-bit wide register with open read/write access privileges at all times for testing basic communication to the
device. This field is free of all security constraints at all times.
6.3.5 Card Manufacturer Code
This field is a 32-bit wide register with read/write access privileges for the customer to define its content. The content of this
field becomes read-only after blowing the PER fuse.
6.3.6 Lot History Code
This field is a 64-bit wide register with content that Atmel defines. This field is read-only.
6.3.7 Issuer Code
This field is a 128-bit wide register with read/write access privileges for customer to define its content. The content of this field
becomes read-only after blowing the PER fuse.
AtmeL
AT88SC0104CA/0204CA/0404CA/0808CA [Datasheet]
Atmel-8664I-CryptoMem-Low-Density-Full-Specification-Datasheet_072015
19
6.3.8 Device Configuration Register (DCR)
This 8-bit register allows selection of the following device configuration options (active low). The values programmed have an
immediate effect on the logic of the device. The default value is one for each bit.
Table 6-4. Device Configuration Register (DCR)
Bit 7
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
SME
UCR
UAT
ETA
CS3
CS2
CS1
CS0
6.3.8.1 SME (Supervisor Mode Enable)
Asserting this bit (SME = 0) enables supervisor mode for Write 7 password such that verifying Write 7 password grants read
and write accesses to all password sets and PACs. Verifying Write 7 password does not grant access to other passwords
when this bit is not asserted (SME = 1).
6.3.8.2 UCR (Unlimited Checksum Reads)
Asserting this bit (UCR = 0) allows unlimited number of checksum reads without requiring a new authentication. Not asserting
this bit (UCR = 1) limits the read of checksum to one attempt after which the device resets the crypto algorithm after executing
the Read Checksum command.
6.3.8.3 UAT (Unlimited Authentication Trials)
Asserting this bit (UAT = 0) disables the Authentication Attempts Counter (AAC) thus allowing unlimited authentication
attempts. The AAC decrements after each unsuccessful attempt but the internal logic ignores it value. Asserting this bit also
prevents reset of the crypto algorithm after reading the MAC in encryption mode. The UAT bit does not affect the password
attempts counter.
6.3.8.4 ETA (Eight Trials Allowed)
Asserting this bit (ETA = 0) extends the trials limit to eight incorrect attempts to authenticate or verify a password. The counter
(AAC or PAC) will decrement ($FF, $FE, $FC, $F8, $F0, $E0, $C0, $80, $00) with each incorrect attempt. Disabling this bit
(ETA = 1) limits authentication and password verification trials to only four incorrect attempts ($FF, $EE, $CC, $88, $00).
6.3.8.5 CS0 CS3: Programmable Chip Select (Only Relevant in Synchronous Protocol)
The four most significant bits (b4 b7) of every command comprise the Chip Select address. All CryptoMemory devices will
respond to the default Chip Select address of $B (1011). Each device also responds to a second Chip Select address
programmed into CS0 - CS3 of the device configuration register. By programming each device to a unique Chip Select
address, it is possible to connect up to 15 devices on the same serial data bus and communicate individually to each. Global
communications to all devices sharing the bus is accomplished using the default Chip Select address $B.
6.3.9 Access Registers
Four (AT88SC0104CA/0204CA/0404CA) or eight (AT88SC0808CA) 8-bit access registers allow personalization of the device.
Each access register works in conjunction with a password/key register to define the security settings for each individual zone
of the user memory. Values in the access registers take immediate effect after programming. The default value for each bit is
one.
Table 6-5. Access Register
Bit 7
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
PM1
PM0
AM1
AM0
ER
WLM
MDF
PGO
AtmeL
AT88SC0104CA/0204CA/0404CA/0808CA [Datasheet]
Atmel-8664I-CryptoMem-Low-Density-Full-Specification-Datasheet_072015
20
6.3.9.1 PM(1:0) Password Mode
Table 6-6. Password Mode
PM0
PM1
Access
1
1
No password required.
1
0
Write password required.
0
*
Read and write passwords required.
When PM = 11, the user zone under protection requires no password. When PM = 10, the zone requires write password
verification for writing and reading is free. When PM = 01 or 00, reading requires the read password verification and writing
requires write password verification; however, proper verification of the write password also grants read access. The password
set required is specified by PW(3:0) in the corresponding passwords/keys register (see Section 6.3.10, Password/Key
Registers). Verification of the write password also allows modification of the read and the write passwords.
6.3.9.2 AM(1:0) Authentication Mode
Table 6-7. Authentication Mode
AM1
AM0
Access
1
1
No authentication required.
1
0
Authentication for write.
0
1
Normal authentication mode.
0
0
Dual access mode.
When AM = 11, the user zone under protection requires no authentication. When AM = 10, the zone requires authentication
only for write accesses and read accesses are free. When AM = 01, the zone requires authentication for both write and read
accesses. In both of these configurations, the Authentication Key (AK) in the corresponding passwords/keys register specifies
the required secret seed and corresponding cryptogram, and when applicable the session encryption key (see the following
Section 6.3.10).
Finally, when AM = 00, the dual access mode is active in which authentication using the Program Only Key (POK) gives a right
to read and program the zone (i.e. write zeros only), while authentication using the AK gives full read and write access to the
zone. In this way, a token application may be implemented, whereby, regular hosts with knowledge of POK may decrement
the stored value, and only master hosts with knowledge of AK may reset the token to its full value. Please see the following
Section 6.3.10on the passwords/keys register for further definition of POK and AK.
Notes: 1. When AM = 00, the POK bits in the corresponding password/key register are ignored.
2. When AM = 00 and PGO = 0; bits in the zone may not be written to one even when using the AK.
3. Requiring authentication automatically requires the use of secure checksums for write operations (See Section
6.1.4, Encrypted Checksum (Message Authentication Code, MAC).
6.3.9.3 ER (Encryption Required)
When ER = 0, the host is required to activate the encryption mode in order to read/write the corresponding user zone. No data
read from or written to the zone may be transmitted in the clear. If ER = 1, the host may activate the encryption mode, but isn't
specifically required to do so by the device.
Atmel
AT88SC0104CA/0204CA/0404CA/0808CA [Datasheet]
Atmel-8664I-CryptoMem-Low-Density-Full-Specification-Datasheet_072015
21
6.3.9.4 WLM (Write Lock Mode)
Asserting this bit (WLM = 0) divides the user zone into 8-byte pages. The first byte of each page becomes the write lock byte
and defines the locked/unlocked status for each byte in the page. Write access is forbidden to a byte if its associated bit in the
write lock byte is set to zero. Bit 7 controls byte 7; bit 6 controls byte 6, etc. By setting bit 0 to zero locks the write lock byte
itself. Enabling Write Lock mode limits write operations to one byte at a time.
6.3.9.5 MDF (Modify Forbidden)
Asserting this bit (MDF = 0) renders the user zone read-only at all times. The user zone must, therefore, be programmed
before setting this bit to zero.
6.3.9.6 PGO (Program Only)
Asserting this bit (PGO = 0) allows changing of data within the user zone under protection from one to zero and never from
zero to one.
6.3.10 Password/Key Registers
Four (AT88SC0104CA/0204CA/0404CA) or eight (AT88SC0808CA) 8-bit password/key registers receive definition during
device personalization. Each password/key register works in conjunction with a corresponding access register to define the
security settings of each zone. The values programmed have an immediate effect on the logic of the device. The default value
is one for each bit. Bit 3 is reserved and should be left as value one.
Table 6-8. Password/Key Register Bit Map
Bit 7
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
AK1
AK0
POK1
POK0
Res
PW2
PW1
PW0
6.3.10.1 AK(1:0) (Authentication Key)
These bits define which of the four secret seeds G0-G3 must be used in an authentication to allow access to the user zone if
authentication is selected in the corresponding access register. Each access register may point to a unique authentication
secret, or access registers for multiple zones may point to the same authentication secret. In this case authentication with a
single secret seed will open several zones.
6.3.10.2 POK(1:0) (Program Only Key)
When the user zone has the dual access mode selected (AM = 00), these bits define which of the four secret seeds G0-G3
must be used in an authentication to allow read and program (i.e. write zeros only) access to the user zone.
6.3.10.3 PW(2:0) (Password Set)
These bits define which of the eight password sets must be presented to allow access to the user zone when the password
mode is selected.
6.3.11 Identification Number
A 56-bit number the customer defines during personalization. It is recommended that a unique identification number be
assigned to each device.
6.3.12 Cryptograms (C0 C3)
Each of these fields contains a 56-bit cryptogram for use during authentication. The internal logic modifies the cryptogram
each time it successfully verifies the authentication. The customer may program an initial value for the cryptogram during
personalization. It is recommended that the initial values be random numbers.
AtmeL
AT88SC0104CA/0204CA/0404CA/0808CA [Datasheet]
Atmel-8664I-CryptoMem-Low-Density-Full-Specification-Datasheet_072015
22
6.3.13 Session Keys (S0 S3)
Each of these fields contains a 64-bit session key for use during encryption. The internal logic modifies the session key each
time it successfully processes authentication or encryption verification. The session keys do not require initial values and does
programming initial values are not necessary.
6.3.14 Secret Seeds (G0-G3)
Each of these fields contains a 64-bit secret seed that is used in conjunction with the corresponding cryptogram and session
key during the authentication and encryption sequences. The customer programs the secret seeds during device
personalization.
6.3.15 Password Sets
The password fields contain eight sets of two 24-bit passwords for read and write operations. The customer defines the values
of these passwords during personalization. Successfully verifying the write password allows modification of the read and the
write passwords of the same set.
6.3.16 Secure Code
The secure code is the Write 7 password. Properly presenting this password grants write access to the configuration memory
during personalization. Atmel defines the initial value of the secure code but the customer may change these values after
successful presentation during a verify password operation for Write 7 password. Table 6-3, Factory Programmed Fields
shows the secure codes for various devices when they leave the Atmel factory. After blowing the PER fuse, verifying Write 7
password no longer grants write access to the configuration memory, and the configuration memory becomes read-only
thereafter.
6.3.17 Password Attempts Counters (PAC)
Each of the sixteen PAC fields contains an 8-bit attempts counter for the verify password process. Each PAC corresponds to a
password. The attempts counter limits the number of incorrect consecutive presentations of the corresponding password to
four, after which it locks the password from future use. The PAC will decrement ($FF, $EE, $CC, $88, $00) with each incorrect
attempt to present the password. The PAC permanently locks the corresponding password once its value reaches $00. Prior
to reaching $00, any correct presentation of the password resets the PAC value to $FF.
6.3.18 Authentication Attempts Counters (AAC)
Each of the four AAC fields contains an 8-bit attempt counter for the authentication process. Each AAC field corresponds to
each authentication key set. The attempts counter limits the number of incorrect consecutive attempts to authenticate to for,
after which it locks the authentication key set from future use. The AAC will decrement ($FF, $EE, $CC, $88, $00) with each
incorrect attempt to authenticate. The AAC permanently locks the corresponding key set once its value reaches $00. Prior to
reaching $00, any correct attempt to authenticate resets the AAC value to $FF.
AT88SC0104CA/0204CA/0404CA/0808CA [Datasheet]
Atmel-8664I-CryptoMem-Low-Density-Full-Specification-Datasheet_072015
23
6.4 Security Fuses
CryptoMemory uses four fuses. The status of these fuses is given in a ‘fuse byte.’ A value of zero indicates the fuse has been
blown. Bits four to seven of this byte are not used as security fuses and are reserved for Atmel use.
Table 6-9. Device Fuses
F7
F6
F5
F4
F3
F2
F1
F0
resv
resv
resv
resv
SEC
PER
CMA
FAB
SEC, PER, CMA, and FAB are nonvolatile fuses blown at the end of various steps in the manufacturing and personalization
process. Once blown, these fuses can never be reset. Atmel blows the SEC fuse to lock the lot history code before the device
leaves the factory. Blowing the remainder of the fuses must follow the sequence:
FAB To lock the ATR and the FAB code portions of the configuration memory.
CMA To lock the card manufacturer code of the configuration memory.
PER To lock the remainder of the configuration memory.
Any attempt to blow a fuse out of sequence will be unsuccessful.
Table 6-10 provides a summary of access rights for all portions of the memory for each fuse condition.
Table 6-10. Configuration Memory Access Control by Security Fuses
Zone
Operation
Fuse
SEC = 0
FAB = 0
CMA = 0
PER = 0
Identification
(Except MTZ and CMC)
Read
Free
Free
Free
Free
Write
Secure Code
Forbidden
Forbidden
Forbidden
Memory Test Zone
(MTZ)
Read
Free
Free
Free
Free
Write
Card Manufacturer Code
(CMC)
Read
Free
Free
Free
Free
Write
Secure Code
Secure Code
Forbidden
Forbidden
Read Only
(Lot History Code)
Read
Free
Free
Free
Free
Write
Forbidden
Forbidden
Forbidden
Forbidden
Access Control
Read
Free
Free
Free
Free
Write
Secure Code
Secure Code
Secure Code
Forbidden
Cryptography
(Except Encryption Keys S)
Read
Free
Free
Free
Free
Write
Secure Code
Secure Code
Secure Code
Forbidden
Encryption Keys
(S)
Read
Secure Code
Secure Code
Secure Code
Forbidden
Write
Secret
Read
Secure Code
Secure Code
Secure Code
Forbidden
Write
Passwords
Read
Secure Code
Secure Code
Secure Code
Write PW
Write
Password Attempts
Counters
(PAC)
Read
Free
Free
Free
Free
Write
Secure Code
Secure Code
Secure Code
Write PW
Forbidden
Read
Forbidden
Forbidden
Forbidden
Forbidden
Write
Note: Secure code: Write 7 password is the secure code until the PER fuse is blown.
AtmeL
AT88SC0104CA/0204CA/0404CA/0808CA [Datasheet]
Atmel-8664I-CryptoMem-Low-Density-Full-Specification-Datasheet_072015
24
7. Protocol Selection
CryptoMemory supports two application areas with different communication protocols:
2-Wire serial communication for embedded applications
ISO 7816 asynchronous T=0 smart card interface
The power-up sequence of CryptoMemory determines what mode it shall operate in. A brief description of each of these
modes follows.
7.1 Synchronous Mode for Embedded Applications
The 2-Wire serial interface is used for fast and efficient communication with logic and controllers. The synchronous mode is
the default after powering up VCC due to the internal and/or external pull-up on RST. For embedded applications using
CryptoMemory in standard plastic packages RST is not bonded out and this is the only communication protocol.
Power-up VCC, RST goes high,
After stable VCC, apply five pulses CLK-SCL, and
CLK-SCL and I/O-SDA may then be driven.
Figure 7-1. Asynchronous Mode
The asynchronous mode is selected when RST is low on a rising edge of CLK. Once the asynchronous mode has been
selected, it is not possible to return to the synchronous mode other than by powering the device off and on again.
Vcc
I/O-SDA
RST
CLK-SCL 1234 5
Atmel LL
AT88SC0104CA/0204CA/0404CA/0808CA [Datasheet]
Atmel-8664I-CryptoMem-Low-Density-Full-Specification-Datasheet_072015
25
7.2 Asynchronous Mode for Smart Card Applications
The asynchronous T=0 protocol defined by ISO 7816-3 is used for compatibility with the industry standard smart card readers.
Selecting this mode requires the following power-up sequence, which complies with ISO 7816-3 for a cold reset in smart card
applications.
Power up VCC; RST, IO-SDA and CLK-SCL are low,
Set I/O-SDA in receive mode,
Provide a clock signal to CLK-SCL,
RST goes high after 400 clock cycles.
The device will respond with a 64-bit ATR code, including historical bytes to indicate the memory density within the
CryptoMemory family. Once the asynchronous mode has been selected, it is not possible to switch to the synchronous mode
without powering off the device.
Table 7-1. ATR Codes for Lower Density CryptoMemory
Atmel Device
TS
T0
TA(1)
TB(1)
TD(1)
TA(2)
T1
T2
AT88SC0104CA
$3B
$B2
$11
$00
$10
$80
$00
$01
AT88SC0204CA
$3B
$B2
$11
$00
$10
$80
$00
$02
AT88SC0404CA
$3B
$B2
$11
$00
$10
$80
$00
$04
AT88SC0808CA
$3B
$B2
$11
$00
$10
$80
$00
$08
Figure 7-2. Power Up Sequence for Smart Card Mode
Smart card applications that support the 2-Wire protocol can also use CryptoMemory in the synchronous mode.
Vcc
I/O-SDA
RST
CLK-SCL
ATR
AtmeL
AT88SC0104CA/0204CA/0404CA/0808CA [Datasheet]
Atmel-8664I-CryptoMem-Low-Density-Full-Specification-Datasheet_072015
26
8. Synchronous Protocol
Communication with the CryptoMemory using the synchronous protocol is very similar to communication with AT24Cxxx Serial
EEPROM devices using a 2-Wire protocol (TWI). Basic command structure and timing are the same; however, a significant
difference exists when reading the CryptoMemory device that will be described below.
8.1 Start-up Sequence
When first powering up the device, five pulses are required on CLK-SCL for reading of internal registers. This can be
accomplished by sending one full command byte to the device. The device will not respond but will then be ready to respond
to the next correct command sequence.
Power-up VCC,
External pull-up resistor pulls I/O-SDA high with VCC,
After stable VCC, five pulses are applied to CLK-SCL,
CLK-SCL and I/O-SDA may be driven.
Figure 8-1. Start-up Sequence
Vcc
I/O-SDA
CLK-SCL 1234 5
Atmel
AT88SC0104CA/0204CA/0404CA/0808CA [Datasheet]
Atmel-8664I-CryptoMem-Low-Density-Full-Specification-Datasheet_072015
27
8.2 Command Set
The command set of CryptoMemory is expanded compared to a Serial EEPROM as the functionality of CryptoMemory
exceeds that of a simple memory device. Each instruction sent to the CryptoMemory must have four bytes:
Command
Address 1
Address 2
N
The N byte defines the number of any additional data bytes to be sent or received from the CryptoMemory device. In addition,
the Random Read command is available. It is the only one byte command but must be preceded by an aborted write
command in order to set up the read address.
Table 8-1. Atmel CryptoMemory Synchronous Command Set
Command Description
Command
Addr 1
Addr 2
N
Data (N)
Write User
Zone
Normal
(AT88SC0104CA-AT88SC0808CA)
$B0
Addr
Addr
N $10
N bytes
With Anti-tearing (All Devices)
$B0
Addr
Addr
N $08
N bytes
Read Read
Random Read
$B1
Details on command usage below.
Read User Zone
Normal Read
$B2
Addr
Addr
N
N bytes
System Write
Write Config Zone
(AT88SC0104CA-AT88SC0808CA)
$B4
$00
Addr
N $10
N bytes
Write Fuses
$B4
$01
Fuse ID
$00
Send Checksum
$B4
$02
$00
$02
2 bytes
Set User Zone
$B4
$03
Zone
$00
Write Config Zone with Anti-tearing
$B4
$08
Addr
N $08
N bytes
Set User Zone with Anti-tearing
$B4
$0B
Zone
$00
System Read
Read Conifg Zone
$B6
$00
Addr
N
Read Fuse Byte
$B6
$01
$00
$01
Read Checksum
$B6
$02
$00
$02
Verify Crypto
Verify Authentication
$B8
$0X
$00
$10
8 Random Bytes
+ 8 Challenge Bytes
X = Key Set (0-3)
Verify Encryption
$B8
$1X
$00
$10
8 Random Bytes
+ 8 Challenge Bytes
X = Key Set (0-3)
Verify
Password
Write Password
$BA
$0X
$00
$03
3 Byte Password
X = Password Set
(0-7)
Read Password
$BA
$1X
$00
$03
3 Byte Password
X = Password Set
(0-7)
H H H H H H \H K K K K K K H H H H H H HJ K K K K AtmeL
AT88SC0104CA/0204CA/0404CA/0808CA [Datasheet]
Atmel-8664I-CryptoMem-Low-Density-Full-Specification-Datasheet_072015
28
8.3 Command Format
Most CryptoMemory commands have the same format as a two wire interface (TWI) write command characterized by a zero in
the LSB of the first byte (device address). The only exception is the Random Read command which has a one in the LSB of
the device address byte.
8.3.1 Write Command Format
The host generates all command and data bytes within a write transaction and sends these to the device. The device
acknowledges each byte.
Figure 8-2. CryptoMemory Write Command
The number of bytes CryptoMemory can write within each call of a write command is constrained by the physical page size of
the EEPROM memory. The maximum number of bytes to write for each call to the write command is $10. All CryptoMemory
write commands comply with the format for the TWI write command.
8.3.2 Read Command Format
The CryptoMemory read commands (Read User Zone, System Read, and Random Read) do not comply with the format of the
TWI read command. The CryptoMemory read user zone and system read commands closely resemble the TWI write
command format by having a zero in the LSB in the device address byte. The Random Read command closely resembles the
format for the TWI read command but requires additional steps to specify the read address.
8.3.2.1 Normal Read: $B2 or $B6 (Read User Zone or System Read)
The CryptoMemory normal read command looks like a TWI write command (LSB of the fist byte = 0) but after the fourth byte of
the command the CryptoMemory device will begin to send data back on the bus. The number of bytes sent by CryptoMemory
will be equal to the value of N.
Figure 8-3. CryptoMemory Normal Read Command
The response of CryptoMemory will cause contention with the host on a standard TWI bus. Typically CryptoMemory cannot be
used on a standard TWI bus but requires a modified TWI protocol to account for the unique read command format.
S
T
A
R
T
S
T
O
P
WRITE
Command Address 1 Address 2 N Data Data x N
A
C
K
A
C
K
A
C
K
A
C
K
A
C
K
A
C
K
xxxx xxx0 0000 0000 0a6-- ---a0 n7--- ---n0 d7--- ---d0 d7--- ---d0
S
T
A
R
T
S
T
O
P
READ
Command Address 1 Address 2
Data Data x N
A
C
K
A
C
K
A
C
K
A
C
K
A
C
K
N
A
C
K
xxxx xxx0 0000 0000 0a6-- ---a0 n7--- ---n0 d7--- ---d0 d7--- ---d0
N
Atmel
AT88SC0104CA/0204CA/0404CA/0808CA [Datasheet]
Atmel-8664I-CryptoMem-Low-Density-Full-Specification-Datasheet_072015
29
8.3.2.2 Random Read: $B1
The Random Read command provides the host ability to sequentially clock data from the device starting from a specified
address. The host needs to issue a “dummy” write operation in order to specify the start address for the Random Read. The
host does this by clocking in the four bytes of the write command and then follows them with a Start condition instead of a data
byte. At this point, the device’s internal logic is pointing to the address from the aborted write operation. The host may then
issue the Random Read command byte ($B1) to which the device will respond with the EEPROM byte at the current address
location and then increment the internal address by one. The device will continue to sequentially send out bytes as long as the
host keeps acknowledging each byte with an ACK. Address roll-over is from the last byte of the current zone to the first byte of
that zone. The host terminates Random Read by issuing a NACK signal instead of an ACK.
Figure 8-4. Random Read Command
CryptoMemory will NACK the N parameter of the dummy write operation if the write were issued to an illegal write location.
The NACK response, however, does not affect the loading of the read address. The Random Read command works for both
configuration and user memory. It is important to implement the CryptoMemory read commands as specified; otherwise
CryptoMemory responses will cause contention on the bus with a host using standard TWI protocol.
8.4 Acknowledge Polling
A stop condition ends each command. Certain commands require an acknowledge polling sequence. Acknowledge polling
consists of sending a Start condition followed by the command byte and determining if the device responds with an ACK. If the
device is not ready for the command it will not acknowledge and the sequence must be repeated (Start condition, command
byte, check for ACK). The ACK indicates the operation has completed but gives no indication of the success or failure of the
command.
Read Commands: No ACK polling required.
Write Commands: ACK polling required except encrypted write commands. Any command may be used.
Set Commands: No ACK polling required.
Verify Commands: ACK polling required with B2 or B6 commands only.
S
T
A
R
TWRITE
Command Address 1 Address 2
Data Data
A
C
K
A
C
K
A
C
K
A
C
K
A
C
K
S
T
A
R
T
N
A
C
K
xxxx xxx0 0000 0000 0a6--- ---a0 n7--- ---n0 xxxx 0001 d7--- ---d0
N
S
T
O
P
Data x N
A
C
K
N
A
C
K
d7--- ---d0
Random Read
Command
AtmeL
AT88SC0104CA/0204CA/0404CA/0808CA [Datasheet]
Atmel-8664I-CryptoMem-Low-Density-Full-Specification-Datasheet_072015
30
The following table lists the specific requirements for ACK polling and the maximum expected delay before the device will ACK
indicating readiness for the next command.
Table 8-2. Minimum Delay for ACK Polling for each Command
Command Description
Command
Addr 1
Addr 2
N
ACK Polling CMD
Delay
Write User
Zone
Normal
$B0
Addr
Addr
N
Required, any CMD
5ms
Normal with Anti-tearing
Encrypted
$B0
Addr
Addr
N
Required, any CMD
20ms
$B0
Addr
Addr
N
No, Send Checksum
0
Encrypted with Anti-tearing
$B0
Addr
Addr
N
No, Send Checksum
0
Random Read
$B1
N/A
N/A
N/A
Not Required
Read User
Zone
$B2
Addr
Addr
N
Not Required
0
System Write
Write Config Zone
$B4
$00
Addr
N
Required, any CMD
5ms
Write Fuses
$B4
$01
Fuse
ID
$00
Required, any CMD
5ms
Send Checksum
$B4
$02
$00
$02
Required, any CMD
5ms
Send Checksum with Anti-tearing
$B4
$02
$00
$02
Required, any CMD
20ms
Set User Zone
$B4
$03
Zone
$00
Not Required
0
Write Config Zone with Anti-tearing
$B4
$08
Addr
N
Required, any CMD
20ms
Set User Zone with Anti-tearing
$B4
$0B
Zone
$00
Not Required
0
System Read
Read Config Zone
$B6
$00
Addr
N
Not Required
0
Read Fuse Byte
$B6
$01
$00
$01
Not Required
0
Read Checksum
$B6
$02
$00
$02
Note Required
0
Verify Crypto
Verify Authentication
$B8
$0X
$00
$10
Required; B2 or B6 only
10ms
Verify Encryption
$B8
$1X
$00
$10
Required; B2 or B6 only
10ms
Verify
Password
Write Password
$BA
$0X
$00
$03
Required; B2 or B6 only
10ms
Read Password
$BA
$1X
$00
$03
Required; B2 or B6 only
10ms
Note: Delays are based on operation at 25° C.
8.5 Device Addressing
The first nibble of the command byte corresponds to the device address. All CryptoMemory devices will respond to the device
address $B. A specific device may be set to respond to another value ($0 to $F) in addition to $B by setting this value in the
second nibble of the Device Configuration Register (DCR) in the configuration memory. The DCR is set to $FF at the Atmel
factory and thus will respond to device address $B and $F unless the DCR is modified. For a device to respond only to $B the
DCR should be set to $B also.
8.6 TWI Command Descriptions
In the following section operations are described in two parts: the instruction is described first from a functional point of view
(parameters and data exchanged), after which they are detailed for the synchronous 2-wire protocol. In these diagrams, values
are shown in binary format with bits to the left transmitted first, i.e. bytes are transmitted most significant bit first.
Atmel
AT88SC0104CA/0204CA/0404CA/0808CA [Datasheet]
Atmel-8664I-CryptoMem-Low-Density-Full-Specification-Datasheet_072015
31
8.7 Write User Zone: $B0
8.7.1 Functional
Figure 8-5. Write User Zone Command Functional Description
Host
Device
Command
Address 1
Address 2
Number of bytes N
Data
N data bytes
Data
The Write User Zone command $B0 allows writing of data in the device's currently selected user zone (the procedure for
selecting a user zone is described below, see Section 8.10 System Write: $B4).
The data byte address to be written is defined by Address 1 and Address 2 in the command. The value N defines how many
bytes are to be written. The maximum number of bytes that may be written is $10 corresponding to the EEPROM page size. In
anti-tearing mode the maximum value for N is $08 for all devices. A write in anti-tearing mode is activated with the set user
zone with anti-tearing command; all subsequent write operations to the user zone will be in anti-tearing mode. A write may be
started in the middle of an EEPROM page but should not extend past the end of the page.
When a Write User Zone command is sent in authentication mode or encryption mode the data is saved in a buffer until a
cryptographic checksum is received. The host must send the checksum it has computed immediately after the Write User
Zone command. If the checksum is valid, CryptoMemory writes the data; if the checksum is incorrect, the data is discarded
and the cryptographic engine is reset. If the host is not allowed to write in the zone, the device will not acknowledge the N
byte. After this command the host must perform ACK polling.
Figure 8-6. Write User Zone Command Structure
S
T
A
R
T
S
T
O
P
Command Address 1 Address 2 Data Data x N
A
C
K
A
C
K
A
C
K
A
C
K
A
C
K
A
C
K
1011 0000 xxxx xxxx xxxx xxxx xxxx xxxx d7--- ---d0 d7--- ---d0
N
AtmeL
AT88SC0104CA/0204CA/0404CA/0808CA [Datasheet]
Atmel-8664I-CryptoMem-Low-Density-Full-Specification-Datasheet_072015
32
8.8 Random Read: $B1
8.8.1 Functional
Figure 8-7. Random Read Sequence Description
Host
Device
Write Command
Address A1
Address A2
Number of bytes N
Random Read Command
Data
N data bytes
Data
The Random Read command $B1 allows reading of data from the devices configuration memory or currently selected user
zone (The Section 8.10 System Write: $B4 describes how to select a user zone).
The Random Read command provides the host ability to sequentially clock data from the device starting from a specified
address. The host needs to first specify the start address to read from in the memory by executing a “dummy” operation. The
host does this by clocking in the four bytes of the write command and then follows them with a Start condition instead of a data
byte. At this point, the device’s internal logic is pointing to the address from the aborted write operation. The host may then
issue the Random Read command byte ($B1) to which the device will respond with the EEPROM byte at the current address
location and then increment the internal address by one. The device will continue to sequentially send out bytes as long as the
host keeps acknowledging each byte with an ACK. During this operation the address will roll-over from the last byte of the
current zone to the first byte of the same zone. The host terminates Random Read by issuing a NACK signal instead of an
ACK.
Figure 8-8. Random Read Command Structure
WRITE
Command Address 1 Address 2 N
N
A
C
KRandom Read
Command
A
C
K
N
A
C
K
S
T
O
P
xxxx xxx00000 00000a6-- ---a0 n7--- ---n0 xxxx 0001d7--- ---d0 d7--- ---d0
Data Data x N
S
T
A
R
T
S
T
A
R
T
A
C
K
A
C
K
A
C
K
A
C
K
A
C
K
Atmel
AT88SC0104CA/0204CA/0404CA/0808CA [Datasheet]
Atmel-8664I-CryptoMem-Low-Density-Full-Specification-Datasheet_072015
33
8.9 Read User Zone: $B2
8.9.1 Functional
Figure 8-9. Read User Zone Command Functional Description
Host
Device
Read Command
Address 1
Address 2
Number of bytes N
Data
N data bytes
Data
The Read User Zone command $B2 allows reading of data from the device's currently selected user zone (the procedure for
selecting a user zone is described in Section 8.10, System Write: $B4).
The data byte address to be read is defined by Address 1 and Address 2 in the command and is internally incremented
following the transmission of each data byte. The value N defines how many bytes CryptoMemory will read, a value of zero will
result in 256 bytes read. The host, however, may cease clocking the device and end the transmission with a NACK and stop at
any time prior to receiving all N bytes. During a read operation the address will roll-over from the last byte of the current zone,
to the first byte of the same zone.
If the host is not allowed to read the zone, the device will not acknowledge the N byte.
Figure 8-10. Read User Zone Command Structure
S
T
A
R
T
S
T
O
P
Command Address 1 Address 2
Data Data x NA
C
K
A
C
K
A
C
K
A
C
K
A
C
K
N
A
C
K
1011 0010 xxxx xxxx xxxx xxxx xxxx xxxx d7--- ---d0 d7--- ---d0
N
AtmeL
AT88SC0104CA/0204CA/0404CA/0808CA [Datasheet]
Atmel-8664I-CryptoMem-Low-Density-Full-Specification-Datasheet_072015
34
8.10 System Write: $B4
Figure 8-11. System Write Command Functional Description
Host
Device
Command
Address 1
Address 2
Number of bytes N
Data
N data bytes
Data
The System Write command allows writing of configuration data to the device. Depending on the value of the Address 1
parameter, the host may write data in the Configuration zone, program the fuses, or set the user zone.
Table 8-3. System Write Command Detail
Command Description
Command
Addr 1
Addr 2
N
Data (N)
Write Config Zone
$B4
$00
Addr
N $10
N bytes
Write Fuses
$B4
$01
Fuse ID
$00
Send Checksum
$B4
$02
$00
$02
2 bytes
Set User Zone
$B4
$03
Zone
$00
8.10.1.1. Write Config Zone
The maximum number of bytes that may be written is $10 and this corresponds to the EEPROM page size. In anti-tearing
mode the maximum value for N is $08 for all devices. A write may be started in the middle of an EEPROM page but should not
extend past the end of the page. If the address provided is an unauthorized address, the device will not write the requested
data. Since access rights vary throughout the Configuration zone, the host may provide an authorized starting address, but a
number of bytes that causes the device to reach unauthorized data. In this case, the device will prevent the internal write cycle
and no bytes will be written in the EEPROM. After this command the host must perform ACK polling.
Atmel
AT88SC0104CA/0204CA/0404CA/0808CA [Datasheet]
Atmel-8664I-CryptoMem-Low-Density-Full-Specification-Datasheet_072015
35
8.10.1.2 Write Fuses
The fuses may only be "programmed", that is written from one to zero. The write fuses operation is allowed only after
successfully presenting the secure code (Write 7 password). The fuses must be blown sequentially: FAB must be blown first,
CMA may be blown only if FAB is zero, and PER only if CMA is zero. After this command the host must perform ACK polling.
The SEC fuse is blown at the Atmel factory to protect lot history information.
Table 8-4. Fuse Identification
Fuse
Fuse ID
SEC
$07
FAB
$06
CMA
$04
PER
$00
8.10.1.3 Send Checksum
To write data to user zones that require authentication or encryption for write access (ER = 0, AM[1:0] = 00, 01, or 10 in the
access register), the host should first carry out the write command $B0. At this point the memory is unchanged and the device
is waiting for the host to provide a valid checksum before initiating the write cycle. The host immediately sends the checksum it
has computed using the System Write command with P1 = $02. Only if the checksum is valid will the device initiate the write
cycle. Furthermore, if the device receives an incorrect checksum, it will clear the authentication privilege. After this command
the host must perform ACK polling.
8.10.1.4 Set User Zone
Before reading and writing data in the user zones, the host must select a zone with this command. At this time the host
chooses whether anti-tearing should be active for this zone.
Table 8-5. Anti-tearing
Command Description
Command
Addr 1
Addr 2
N
Data (N)
Write Config Zone with Anti-tearing
$B4
$08
Addr
N $08
N bytes
Set User Zone with Anti-tearing
$B4
$0B
Zone
$00
Data written to the Configuration zone may be done with anti-tearing enabled by setting Address 1 to $08 of the write
Configuration zone command.
To enable anti-tearing for writes to a user zone, a set user zone command is executed with Address 1 set to $0B. All
subsequent Write User Zone commands will be executed with anti-tearing enabled until the next set user zone command.
Anti-tearing should be turned off if not required, as it would otherwise cause more write cycles than necessary
Figure 8-12. System Write Command Detail
S
T
A
R
T
S
T
O
P
Command Address 1 Address 2 Data Data x N
A
C
K
A
C
K
A
C
K
A
C
K
A
C
K
A
C
K
1011 0100 0000 xxxx xxxx xxxx xxxx xxxx d7--- ---d0 d7--- ---d0
N
AtmeL
AT88SC0104CA/0204CA/0404CA/0808CA [Datasheet]
Atmel-8664I-CryptoMem-Low-Density-Full-Specification-Datasheet_072015
36
8.11 System Read: $B6
8.11.1 Functional
Figure 8-13. System Read Command Functional Description
Host
Device
Read Command
Address 1
Address 2
Number of bytes N
Data
N data bytes
Data
The system read command allows reading of system data from the device. Depending on the value of Address 1, the host may
read the data in the Configuration zone, or the fuses.
Table 8-6. Zone Configuration Example
Command Description
Command
Addr 1
Addr 2
N
Read Config Zone
$B6
$00
Addr
N
Read Fuse Byte
$B6
$01
$00
$01
Read Checksum
$B6
$02
$00
$02
8.11.2 Read Config Zone
The data byte address to be read is defined by Address 2 in the command and is internally incremented following the
transmission of each data byte. The value N defines how many bytes CryptoMemory will read, a value of zero will result in
256 bytes read. If the address provided is an unauthorized address, the device will not ACK the N byte and will not return any
data. Since access rights vary throughout the Configuration zone, the host may provide an authorized starting address and a
number of bytes N that causes the device to reach unauthorized data. In this case the device will transmit the fuse byte (see
below) in place of unauthorized bytes.
8.11.3 Read Fuse Byte
Fuse data is returned in the form of a single byte. Bits zero to three represent the fuse states; a value of zero indicates the
fuse has been blown. Bits four to seven are not used as security fuses and are reserved by Atmel.
Table 8-7. Fuse Byte Definition
F7
F6
F5
F4
F3
F2
F1
F0
resv
resv
resv
resv
SEC
PER
CMA
FAB
Atmel
AT88SC0104CA/0204CA/0404CA/0808CA [Datasheet]
Atmel-8664I-CryptoMem-Low-Density-Full-Specification-Datasheet_072015
37
8.11.3.1 Read Checksum
The checksum consists of two bytes, and the Read Checksum command must be sent with parameter N = 2.
Figure 8-14. System Read
S
T
A
R
T
S
T
O
P
Command Address 1 Address 2
Data Data x N
A
C
K
A
C
K
A
C
K
A
C
K
A
C
K
N
A
C
K
1011 0110 0000 xxxx xxxx xxxx xxxx xxxx d7--- ---d0 d7--- ---d0
N
AtmeL
AT88SC0104CA/0204CA/0404CA/0808CA [Datasheet]
Atmel-8664I-CryptoMem-Low-Density-Full-Specification-Datasheet_072015
38
8.12 Verify Crypto: $B8
8.12.1 Functional
Figure 8-15. Verify Crypto Command Functional Description
Host
Device
Command
Key Index
8 random bytes
Q1
Q2
Q3
Q4
Q5
Q6
Q7
Q8
8 challenge bytes
CH1
CH2
CH3
CH4
CH5
CH6
CH7
CH8
When the device receives the Verify Crypto command, it computes a challenge based on the received random number, Q, the
internally stored associated cryptogram, Ci, and secret seed, Gi (or session encryption key, Si). The device also decrements
the associated attempts counter. It then compares the computed challenge with the challenge sent by the host. If the
challenges match, the device computes and writes a new Ci and Si. The device utilizes the success or failure information of the
authentication process and updates the attempts counter accordingly.
Key index:
b0000_00nn : Secret Seed G0-G3
b0001_00nn : Session Encryption Key S0-S3
Data :
Q : Host Random Number, 8 bytes
CH : Host Challenge, 8 bytes
Atmel
AT88SC0104CA/0204CA/0404CA/0808CA [Datasheet]
Atmel-8664I-CryptoMem-Low-Density-Full-Specification-Datasheet_072015
39
Figure 8-16. Verify Crypto
Once the sequence has been carried out, the device requires the host to perform an ACK polling with either the read user
zone $B2 command or system read $B6 command. To verify whether the authentication succeeded, the host could either read
the associated attempts counter to confirm the value is $FF, or read the post authentication cryptogram from the device and
compare with the cryptogram generated when the host computed the challenge bytes.
S
T
A
R
T
S
T
O
P
Command Key Index Parameter 2 Data x 16
A
C
K
A
C
K
A
C
K
A
C
K
A
C
K
1011 1000 000e 00nn xxxx xxxx 0001 0000 d7--- ---d0
N=16
AtmeL
AT88SC0104CA/0204CA/0404CA/0808CA [Datasheet]
Atmel-8664I-CryptoMem-Low-Density-Full-Specification-Datasheet_072015
40
8.13 Verify Password: $BA
8.13.1 Functional
Figure 8-17. Verify Password Command Functional Description
Host
Device
Command
Password Index
PW1
3 password bytes
PW2
PW3
Read password indices: $10 to $17 for passwords 0, 1, 2, and 7.
Write password indices: $00 to $07 for passwords 0, 1, 2, and 7.
Secure code index: $07 (equivalent to Write Password 7).
Four password index bits "r" and "ppp" indicate the password to compare:
r = 0 : Write Password
r = 1 : Read Password
p2p1p0 : Password Set Number
Figure 8-18. Verify Password
Once the sequence has been carried out, the device requires the host to perform an ACK polling sequence with the system
read command $B6. In order to know whether the inserted password was correct, the host can read the corresponding
attempts counter and verify the value is zero.
S
T
A
R
T
S
T
O
P
Command PW Index Parameter 2 Data x 3
A
C
K
A
C
K
A
C
K
A
C
K
A
C
K
1011 1010 000r 0p2p1p0 xxxx xxxx 0000 0011 d7--- ---d0
N=3
Atmel
AT88SC0104CA/0204CA/0404CA/0808CA [Datasheet]
Atmel-8664I-CryptoMem-Low-Density-Full-Specification-Datasheet_072015
41
9. Initialization Example
The first step in initializing CryptoMemory is to determine what data is to be stored in the device and what the security settings
need to be to protect this data. Once defined, determine the proper settings for CryptoMemory registers and select values for
passwords. To initialize the CryptoMemory device, the following sequence is recommended to take place in a secure location
to protect sensitive data and passwords that may be loaded into the device.
9.1 Write Data to User Zones
In the default configuration from Atmel, all user zones have free access rights. Writing initial data into the user zones should be
done before setting security configurations. Use the set user zone command and Write User Zone command to write initial
data into the user zones. The Read User Zone command may be used to verify the data written.
9.2 Unlock the Configuration Memory
Before any data can be written to the Configuration zone, it must be unlocked by presenting the correct security code (Write 7
password). Use the Verify Password command with the proper secure code supplied by Atmel to unlock the Configuration
zone. Use the Read Config Zone command to read back the security code at address $E9 for verification that the
Configuration zone has been unlocked.
9.3 Write Data to the Configuration Memory
Writing this data is accomplished by performing the Write Config Zone command at the appropriate address location. The
Read Config Zone command may be used to verify the data written. As soon as values are written to the registers, keys, and
passwords, they become effective in determining the security of the user zones.
9.4 Set Security Fuses
Once all data is written and verified into user zones and the Configuration zone, the security fuses should be set before the
device is released from the secure location used for device initialization. There are three fuses, FAB, CMA and PER, which
must be set. These three fuses must be set in the order listed (FAB, then CMA, then PER). The Write Fuse command is used
to set each of the three fuses individually. The Read Fuse command may be used to check the status of all three fuses. Once
all fuses have been set, the Read Fuse command should return a value of zero for the second nibble of the fuse byte.
The AT88SC0104CA is used for this example. A small pattern is written into the first two user zones. Security for each of these
two user zones and the associated register values are shown in the table below. Simple values for passwords are used.
Table 9-1. CryptoMemory Asynchronous Command Set
User Zone
Data
Security Requirements
Access Register
Password/Key Register
0
Zone 0
None
$FF
$FF
1
Zone 1
Read/Write Password (Set 1)
$7F
$F9
2
Zone 2
Read/Write Authentication (Set 2)
$DF
$BF
3
Zone 3
Read/Write Password (Set 1)
Read/Write Authentication (Set 2)
with encryption required
$57
$B9
AtmeL
AT88SC0104CA/0204CA/0404CA/0808CA [Datasheet]
Atmel-8664I-CryptoMem-Low-Density-Full-Specification-Datasheet_072015
42
The following shows the 2-Wire commands sent to the CryptoMemory device for the purpose of initializing the device. The flow
is consistent with the steps described above; comments have been added as indicated with an asterisk (*).
*Atmel AT88SC0104CA Initialization Example
*WRITE DATA TO USER ZONES
*Set User Zone 0
B4 03 00 00
*Write data = Zone 0 Data
B0 00 00 0B 5A 6F 6E 65 20 30 20 44 61 74 61
*Set User Zone 1
B4 03 01 00
*Write data = Zone 1 Data
B0 00 00 0B 5A 6F 6E 65 20 31 20 44 61 74 61
*Set User Zone 2
B4 03 02 00
*Write data = Zone 2 Data
B0 00 00 0B 5A 6F 6E 65 20 32 20 44 61 74 61
*Set User Zone 3
B4 03 03 00
*Write data = Zone 3 Data
B0 00 00 0B 5A 6F 6E 65 20 33 20 44 61 74 61
*UNLOCK CONFIGURATION ZONE
BA 07 00 03 DD 42 97
*WRITE CODES IN CONFIGURATION ZONE
*Write Card Mfg Code = P001
B4 00 0B 04 50 30 30 31
*Write Identification Number = 00000000012345
B4 00 19 07 00 00 00 00 01 23 45
*Write Issuer Code = STATION 035
B4 00 40 10 53 54 41 54 49 4F 4E 20 30 33 35 00 00 00 00 00
*WRITE REGISTERS IN CONFIGURATION ZONE
*Write Registers AR1/PR1 = 7F F9
B4 00 22 02 7F F9 DF BF 57 B9
*WRITE KEYS IN CONFIGURATION MEMORY
*Write Ci for set 2 = 22222222222222
B4 00 71 07 22 22 22 22 22 22 22
*Write Gc for set 2 = 5B4F9AE4B5098BE7
B4 00 A0 08 5B 4F 9A E4 B5 09 8B E7
*WRITE PASSWORDS IN CONFIGURATION MEMORY
*WRITE PASSWORDS IN CONFIGURATION ZONE
*Write Passwords, read 7 = 10 00 01, write 7 = 11 00 11
B4 00 B9 07 11 00 11 FF 10 00 01
*READ ENTIRE CONFIGURATION ZONE TO VERIFY
B6 00 00 F0
Atmel
AT88SC0104CA/0204CA/0404CA/0808CA [Datasheet]
Atmel-8664I-CryptoMem-Low-Density-Full-Specification-Datasheet_072015
43
*Device Response:
3B B2 11 00 10 80 00 01 10 10 FF 50 30 30 31 FF
8C AD A8 10 0A AB FF FF FB 00 00 00 00 01 23 45
FF FF 7F F9 FF FF FF FF FF FF FF FF FF FF FF FF
FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
53 54 41 54 49 4F 4E 20 30 33 35 00 00 00 00 00
FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
FF FF FF FF FF FF FF FF FF 11 00 11 FF 10 00 01
FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
*SET SECURITY FUSES
*Set FAB Fuse
B4 01 06 00
*Set CMA Fuse
B4 01 04 00
*Set PER Fuse
B4 01 00 00
*Read Fuse Byte = X0
B6 01 00 01
*Device Response:
00
90 00
‘ 8 data bits . <7 4}="" atmel="">
AT88SC0104CA/0204CA/0404CA/0808CA [Datasheet]
Atmel-8664I-CryptoMem-Low-Density-Full-Specification-Datasheet_072015
44
10. Asynchronous T=0 Protocol
10.1 Character Format
The CryptoMemory complies with the asynchronous T=0 protocol defined in ISO 7816-3. The character format is shown in the
following figure.
Note: The byte is transmitted with the least significant bit first.
Figure 10-1. Character Format
Even parity is used: the parity bit is such that the overall sum of bits in the data byte and the parity bit is an even number. If a
transmission error is detected, the receiving device indicates this by applying a low level on the I/O channel during the guard
time. This tells the transmitting device to retransmit the byte.
10.2 Command format
The command sequence is as follows:
1. In compliance with ISO 7816-3, the host must send the header consisting of five characters: CLA, INS, P1, P2, P3.
CLA refers to a class of instructions. This byte isn't tested by the device.
INS is the instruction byte.
P1 and P2 are reference bytes, such as a data byte address or password index.
P3 is the number of data bytes transferred during the command. For outgoing transfers (e.g. read commands),
P3 = 0 means that 256 data bytes will be emitted by the card. For incoming commands, P3 = 0 means that no
data bytes will be transferred.
2. The device replies with a "procedure byte normally equal to the INS code received. If a problem occurred, then the
device will respond with a status word pair SW1-SW2, indicating the end of the command.
3. Data transfer (P3 bytes).
4. A final SW1-SW2 sequence gives the status of the device after completion of the command. A normal completion is
indicated by SW1-SW2 = $90-$00.
Note: For all bytes transmitted by the device or by the host, including header, procedure, status and data bytes, if
a parity error is detected, the receiver requests that byte to be sent again (see character format).
(n ± 0,2) etu
Parity bit Next Start bitStart bit
Guard Time
d d d d d d d d p
0tt t
I/O
Z
A
8 data bits
0 1
110n
234567
Atmel
AT88SC0104CA/0204CA/0404CA/0808CA [Datasheet]
Atmel-8664I-CryptoMem-Low-Density-Full-Specification-Datasheet_072015
45
10.3 Command Set
Table 10-1. CryptoMemory Asynchronous Command Set
Command Description
CLA
INS
P1
P2
P3
Data (N)
B0
Write User
Zone
Normal
$00
$B0
Addr
Addr
N $10
N bytes
With Anti-tearing
$00
$B0
Addr
Addr
N $08
N bytes
B2
Read User
Zone
Read User Zone
$00
$B2
Addr
Addr
N
B4
System
Write
Write Config Zone
$00
$B4
$00
Addr
N $10
N bytes
Write Fuses
$00
$B4
$01
Fuse ID
$00
Send Checksum
$00
$B4
$02
$00
$02
2 bytes
Set User Zone
$00
$B4
$03
Zone
$00
Write Config Aone w/a-t
$00
$B4
$08
Addr
N $08
N bytes
Set User Zone w/a-t
$00
$B4
$0B
Zone
$00
B6
System
Read
Read Config Zone
$00
$B6
$00
Addr
N
Read Fuse Byte
$00
$B6
$01
$00
$01
Read Checksum
$00
$B6
$02
$00
$02
B8
Verify
Crypto
Verify Authentication
$00
$B8
$0X
$00
$10
8 Random Bytes
+ 8 Challenge Bytes
X = Key Set (0-3)
Verify Encryption
$00
$B8
$1X
$00
$10
8 Random Bytes
+ 8 Challenge Bytes
X = Key Set (0-3)
BA
Verify
Password
Write Password
$00
$BA
$0X
$00
$03
3 Byte Password
X = Password Set
(0, 1, 2, or 7)
Read Password
$00
$BA
$1X
$00
$03
3 byte Password
X = Password Set
(0, 1, 2, or 7)
10.3.1 Status Words
Table 10-2. Asynchronous Mode Return Status Words Definitions
SW1 SW2
Meaning
$62 $00
The memory is unchanged (waiting for checksum).
$67 $00
The length is incorrect.
$69 $00
The command is unauthorized.
$6B $00
The address is incorrect.
$6D $00
The instruction code is invalid.
$90 $00
The command was successfully executed.
AtmeL
AT88SC0104CA/0204CA/0404CA/0808CA [Datasheet]
Atmel-8664I-CryptoMem-Low-Density-Full-Specification-Datasheet_072015
46
These status words indicate the state of the device at the end of the command. In normal conditions, the device sends the INS
byte as the procedure byte, and $90 $00 as the final status word. In certain conditions described below, the device may
interrupt the command by returning a status word in place of INS as the procedure byte.
$67 $00 is returned as a procedure byte when the number of data bytes to be transferred is incorrect.
$69 $00 is returned after read/write commands as procedure bytes if the host is not allowed to read/write at the address
provided. It is also returned after password commands if the maximum number of attempts has been exceeded. The device
will return $69 $00 as a final status word in place of $90 $00, if the password presentation failed.
$6B $00 is returned as procedure bytes if the address is incorrect.
$6D $00 is returned as procedure bytes if the INS code received is not supported.
10.3.2 Example: Write EEPROM command
The following illustrates the data exchanges that occur during a write operation of four bytes: $04, $09, $19, and $97 to
addresses $02, $03, $04, and $05 in the current user zone.
Start
Finish
Host
Device
Val
Note
CLA
**
Class (ignored by CryptoMemory).
INS
$B0
Write instruction.
P1
**
Address byte A1 (ignored by 0104C - 1616C).
P2
$02
Address byte A2 = $02.
P3
$04
Four data bytes.
INS
$B0
Device responds with INS code.
Data
$04
Byte to be written at start address $02
Data
$09
Byte to be written at address $03.
Data
$19
Byte to be written at address $04.
Data
$97
Byte to be written at address $05.
Write Cycle
~5ms
SW1
90
Write operation successful.
SW2
$00
Atmel
AT88SC0104CA/0204CA/0404CA/0808CA [Datasheet]
Atmel-8664I-CryptoMem-Low-Density-Full-Specification-Datasheet_072015
47
10.4 T=0 Command Descriptions
The command set of CryptoMemory is expanded compared to a Serial EEPROM as the functionality of CryptoMemory
exceeds that of a simple memory device. Each instruction sent to the CryptoMemory must have four bytes:
Command
Address 1
Address 2
N
The N byte defines the number of any additional data bytes to be sent or received from the CryptoMemory device.
10.5 Write User Zone: $B0
10.5.1 Functional
Figure 10-2. Write User Zone Command Functional Description
Host
Device
Command
Address A1
Address A2
Number of bytes N
Data
N data bytes
Data
The Write User Zone command $B0 allows writing of data into the device's currently selected user zone (the procedure for
selecting a user zone is described below.
The maximum numbers of bytes that may be written in a single write operation is $10 and corresponds to the EEPROM page
size. Each data byte within a page must only be loaded once. In anti-tearing mode the maximum value for N is $08 for all
devices. A write in anti-tearing mode is activated with the set user zone command with the anti-tearing option (00 B4 0B zz
00); all subsequent writes to the user zone will be in anti-tearing mode.
When a Write User Zone command is sent in authentication mode or encryption mode the data is saved in a buffer until a
cryptographic checksum is received. The host must send the checksum it has computed immediately after the Write User
Zone command. If the checksum is valid, CryptoMemory writes the data; if the checksum is incorrect the data is discarded and
the cryptographic engine is reset.
If the host is not allowed to write in the zone, the device will return the "Command Unauthorized" code ($69 $00) after it has
received the P3 byte.
Table 10-3. Write User Zone Command Structure
Command Header
Data Sent
CLA
INS : Command
P1 : Address 1
P2 : Address 2
P3 : N
Data(1)
...
Data(N)
**
$B0
0000 0000
0a6-- ---a0
000n4 --- n0
d7--- ---d0
...
d7--- ---d0
AtmeL
AT88SC0104CA/0204CA/0404CA/0808CA [Datasheet]
Atmel-8664I-CryptoMem-Low-Density-Full-Specification-Datasheet_072015
48
10.6 Read User Zone: $B2
10.6.1 Functional
Figure 10-3. Read User Zone Command Functional Description
Host
Device
Read Command
Address 1
Address 2
Number of bytes N
Data
N data bytes
Data
The Read User Zone command $B2 allows reading of data from the device’s currently selected user zone (the procedure for
selecting a user zone is described below). The byte address is internally incremented following the transmission of each data
byte. During a read operation, the address will roll-over from the last byte of the current zone, to the first byte of the same
zone.
If the host is not allowed to read the zone, the device will return the "Command Unauthorized" code ($69 $00) after it has
received the header.
Table 10-4. Read User Zone Command Structure
Command Header
Data Returned
CLA
INS : Command
P1 : Address 1
P2 : Address 2
P3 : N
Data(1)
...
Data(N)
**
$B2
0000 0000
0a6-- ---a0
n7 --- n0
d7--- ---d0
...
d7--- ---d0
AtmeL
AT88SC0104CA/0204CA/0404CA/0808CA [Datasheet]
Atmel-8664I-CryptoMem-Low-Density-Full-Specification-Datasheet_072015
49
10.7 System WRITE: $B4
10.7.1 Functional
Figure 10-4. System Write Command Functional Description
Host
Device
Command
Address P1
Address P2
Number of bytes N
Data
N data bytes
Data
The System Write command allows writing of system data to the device. Depending on the value of the P1 parameter, the host
may write data in the configuration memory, program the fuses, send a checksum or set the user zone.
Table 10-5. System Write Command Detail
Command
CLA
INS
P1
P2
P3
Data(N)
Write Config Zone
$00
$B4
$00
ADDR
N $10
N bytes
Write Fuses
$00
$B4
$01
Fuse ID
$00
Send Checksum
$00
$B4
$02
$00
$02
2 bytes
Set User Zone
$00
$B4
$03
Zone
$00
The anti-tearing function is controlled by P1: the host may choose to write in the Configuration zone with anti-tearing enabled
by setting P1 = $08 instead of $00. Similarly, the host may choose to activate anti-tearing for a user zone by carrying out the
Set user zone command with P1 = $0B instead of $03. All subsequent Write User Zone commands are then carried out with
anti-tearing enabled until the next set user zone command. Anti-tearing should be turned off if not required, as it would
otherwise cause more write cycles than necessary.
Table 10-6. Anti-tearing
Command Description
CLA
INS
P1
P2
P3
Data(N)
Write Config Zone w/ a-t
$00
$B4
$08
ADDR
N $08
N bytes
Set User Zone w/ a-t
$00
$B4
$0B
Zone
$00
AtmeL
AT88SC0104CA/0204CA/0404CA/0808CA [Datasheet]
Atmel-8664I-CryptoMem-Low-Density-Full-Specification-Datasheet_072015
50
10.7.2 Write Config Zone
The maximum number of bytes to write for each call of the write command is $16 and corresponds to the EEPROM page size.
Each data byte within a page must only be loaded once. In anti-tearing mode the maximum value for N is $08 for all devices.
If the address provided at P2 is an unauthorized address, the device will return the "Command Unauthorized" code ($69 $00)
after it has received the header. Since access rights vary throughout the Configuration zone, the host may provide an
authorized starting address, but a number of bytes that causes the device to reach unauthorized data. In this case, the device
will prevent the internal write cycle and no bytes will be written in the EEPROM. At the end of the command the "Command
Unauthorized" code ($69 $00) will be returned instead of $90 $00 to indicate that no write cycle occurred.
10.7.3 Write Fuses
Table 10-7. Fuse Bytes
Fuse
Fuse ID
SEC
$07
FAB
$06
CMA
$04
PER
$00
The fuses may only be programmed, that is written from one to zero. The write fuses operation is only allowed after
successfully presenting the secure code (Write 7 password). The fuses must be blown sequentially:
1. FAB must be blown first,
1. CMA may be blown only if FAB is zero,
1. PER only if CMA is zero.
The SEC fuse is blown at the Atmel factory to protect lot history information.
10.7.4 Send Checksum
To write data to user zones which require authentication or encryption for write access (ER = “0”, AM [1:0] = “00”, “01”, or “10”
in the access register), the host should first carry out the write command $B0, after which the device will return a special status
word: $62 $00. At this point the memory is unchanged and the device is waiting for the host to provide a valid checksum
before initiating the write cycle. The host immediately sends the checksum it has computed using the System Write command
with P1 = $02. Only if the checksum is valid will the device initiate the write cycle; furthermore, if the device receives an
incorrect checksum, it will clear the authentication privilege. After this command the host must perform ACK polling.
10.7.5 Set User Zone
Before reading and writing data in the user zones, the host should select a zone with this command. At this time the host may
choose whether anti-tearing should be active for this zone.
Table 10-8. System Write Command Structure
Command Header
Data Sent
CLA
INS : Command
P1
P2
P3
Data(1)
...
Data(N)
**
$B4
p7 --- p0
p7 --- p0
n7 --- n0
d7--- ---d0
...
d7--- ---d0
AtmeL
AT88SC0104CA/0204CA/0404CA/0808CA [Datasheet]
Atmel-8664I-CryptoMem-Low-Density-Full-Specification-Datasheet_072015
51
10.8 System READ: $B6
10.8.1 Functional
Figure 10-5. System READ Command Functional Description
Host
Device
Read Command
Address 1
Address 2
Number of bytes N
Data
N data bytes
Data
The System Read command allows reading of the system data from the device. Depending on the value of the P1 parameter,
the host may read the data in the configuration memory, the fuses, or a checksum.
Table 10-9. System READ Command Detail
Command
CLA
INS
P1
P2
P3
Data (N)
Read Config Zone
$00
$B6
$00
addr
N
Read Fuse Byte
$00
$B6
$01
$00
$01
Read Checksum
$00
$B6
$02
$00
$02
10.8.2 Read Config Zone
To read 256 bytes, the host should set N = $00. This is true for any outgoing command, and is defined by ISO 7816-3. If the
address provided at P2 is an unauthorized address, the device will return the "Command Unauthorized" code ($69 $00) after it
has received the header. Since access rights vary throughout the Configuration zone, the host may provide an authorized
starting address, but a number of bytes N that causes the device to reach unauthorized data. In this case, the device will
transmit the authorized bytes, but unauthorized bytes will be replaced by the "fuse byte" (see below). At the end of this
command the "Command Unauthorized" code ($69 $00) will be returned instead of $90 $00 to indicate that some of the bytes
returned are not valid
10.8.3 Read Fuse Byte
Fuse data is returned in the form of a single byte. Bits 0 to 3 represent the fuse states; a value of ‘0’ indicates the fuse has
been blown. Bits 4 to 7 are not used as security fuses and are reserved by Atmel.
Table 10-10. Fuse Byte Definition
F7
F6
F5
F4
F3
F2
F1
F0
resv
resv
resv
resv
SEC
PER
CMA
FAB
AtmeL
AT88SC0104CA/0204CA/0404CA/0808CA [Datasheet]
Atmel-8664I-CryptoMem-Low-Density-Full-Specification-Datasheet_072015
52
10.8.4 System Read Command Structure
Table 10-11. System Read
Command Header
Data Returned
CLA
INS : Command
P1
P2
P3
Data(1)
...
Data(N)
**
$B6
p7 --- p0
p7 --- p0
n7 --- n0
d7--- ---d0
...
d7--- ---d0
10.8.5 Read Checksum
The checksum consists of two bytes, and the Read Checksum command must be sent with parameter P3 = 2.
Table 10-12. System READ
System Read
Data Returned
CLA
INS : Command
P1
P2
P3
Data(1)
...
Data(N)
**
$B6
p7 --- p0
p7 --- p0
n7 --- n0
d7--- ---d0
...
d7--- ---d0
Atmel
AT88SC0104CA/0204CA/0404CA/0808CA [Datasheet]
Atmel-8664I-CryptoMem-Low-Density-Full-Specification-Datasheet_072015
53
10.9 Verify CRYPTO: $B8
10.9.1 Functional
Figure 10-6. Verify Crypto Command Functional Description
Host
Device
Command
Key Index
8 random bytes
Q1
Q2
Q3
Q4
Q5
Q6
Q7
Q8
8 challenge bytes
CH1
CH2
CH3
CH4
CH5
CH6
CH7
CH8
When the device receives the Verify Crypto command, it computes a challenge based on the received random number, Q, the
internally stored associated cryptogram, Ci, and secret seed, Gi (or session encryption key, Si). The device also increments the
associated attempts counter. It then compares the computed challenge with the challenge sent by the host. If the challenges
match, the device computes and writes a new Ci and Si. The device utilizes the success or failure information of the
authentication process and updates the Authentication Attempts Counter accordingly.
Key index:
b0000_00nn : Secret Seed G0-G3
b0001_00nn : Session Encryption Key S0-S3
Data :
Q : Host random number, 8 bytes
CH : Host challenge, 8 bytes
AtmeL
AT88SC0104CA/0204CA/0404CA/0808CA [Datasheet]
Atmel-8664I-CryptoMem-Low-Density-Full-Specification-Datasheet_072015
54
Table 10-13. Verify Crypto
Verify Crypto
Data Sent
CLA
INS : Command
P1
P2
P3
Q1
Q8
CH1
CH8
**
$B8
000e 00nn
**
$10
d7--- ---d0
d63--- ---d56
d7--- ---d0
d63--- ---d56
The device increments the associated attempts counter each time prior to verifying the challenge, to prevent attacks. If the
authentication succeeds, the device memorizes this success, clears the attempts counter and returns $90 $00. If the
authentication fails, the device simply returns $69 $00. If the maximum number of trials has been exceeded, the device will
return $69 $00 instead of the INS code, after receiving the header, to indicate the command is unauthorized.
Atmel
AT88SC0104CA/0204CA/0404CA/0808CA [Datasheet]
Atmel-8664I-CryptoMem-Low-Density-Full-Specification-Datasheet_072015
55
10.10 Verify Password: $BA
10.10.1 Functional
Figure 10-7. Verify Password Command Functional Description
Host
Device
Command
Password Index
PW1
3 password bytes
PW2
PW3
Read password indices: $10 to $17 for passwords 0, 1, 2, and 7.
Write password indices: $00 to $07 for passwords 0, 1, 2, and 7.
Secure code index: $07 (equivalent to Write Password 7).
Four password index bits "r" and "ppp" indicate the password to compare:
r = 0: Write password,
r = 1: Read password,
p2p1p0: Password set number
Table 10-14. Verify Password Command Structure
Command Structure
Data Sent
CLA
INS : Command
P1
P2
P3
PW1
PW2
PW3
**
$BA
000r 0p2p1p0
**
$30
d7--- ---d0
d15--- ---d8
d23--- ---d16
If the maximum number of trials has been exceeded, the device will return $69 $00 instead of the INS code, after receiving the
header, to indicate the command is unauthorized. The device increments the associated attempts count before verifying the
password, to prevent attacks. If the password is correct, the device memorizes this success, clears the attempts count and
returns $90 $00. If the password is wrong, the device simply returns $69 $00 after incrementing the attempts count. The
Write 7 password is also known as the secure code and must be properly presented before access to the Configuration zone
is granted when personalizing the device.
AtmeL
AT88SC0104CA/0204CA/0404CA/0808CA [Datasheet]
Atmel-8664I-CryptoMem-Low-Density-Full-Specification-Datasheet_072015
56
11. Initialization Example
The first step in initializing CryptoMemory is to determine what data is to be stored in the device and what the security settings
need to be to protect this data. Once defined, determine the proper settings for CryptoMemory registers and select values for
passwords. To initialize the CryptoMemory device, the following sequence is recommended to take place in a secure location
to protect sensitive data and passwords that may be loaded into the device.
11.1 Write Data to User Zones
In the default configuration from Atmel, all user zones have free access rights. Writing initial data into the user zones should be
done before setting security configurations. Use the set user zone command and Write User Zone command to write initial
data into the user zones. The Read User Zone command may be used to verify the data written.
11.2 Unlock the Configuration Memory
Before any data can be written to the Configuration zone, it must be unlocked by presenting the correct security code (Write 7
Password). Use the Verify Password command with the proper secure code supplied by Atmel to unlock the Configuration
zone. Use the Read Config Zone command to read back the security code at address $E9 for verification that the
Configuration zone has been unlocked.
11.3 Write Data to the Configuration Memory
Writing this data is accomplished by performing the Write Config Zone command at the appropriate address location. The
Read Config Zone command may be used to verify the data written. As soon as values are written to the registers, keys, and
passwords, they become effective in determining the security of the user zones.
11.4 Set Security Fuses
Once all data is written and verified into user zones and the Configuration zone the security fuses should be set before the
device is released from the secure location used for device initialization. There are three fuses, FAB, CMA, and PER that must
be set. These three fuses must be set in the order listed (FAB, then CMA, then PER). The Write Fuse command is used to set
each of the three fuses individually. The Read Fuse command may be used to check the status of all three fuses. Once all
fuses have been set the Read Fuse command should return a value of zero for the second nibble of the fuse byte.
The AT88SC0104CA is used for this example. A small pattern is written into the first two user zones. Security for each of these
two user zones and the associated register values are shown in the table below. Simple values for passwords are used.
Table 11-1. Zone Configuration Example
User Zone
Data
Security Requirements
Access Register
Password/Key Register
0
Zone 0
None
$FF
$FF
1
Zone 1
Read/Write Password (Set 1)
$7F
$F9
2
Zone 2
Read/Write Authentication (Set 2)
$DF
$BF
3
Zone 3
Read/Write Password (Set 1),
Read/Write Authentication (Set 1)
with Encryption Required
$57
$B9
Atmel
AT88SC0104CA/0204CA/0404CA/0808CA [Datasheet]
Atmel-8664I-CryptoMem-Low-Density-Full-Specification-Datasheet_072015
57
The following shows the TPDU commands sent to the CryptoMemory device for the purpose of initializing the device. The flow
is consistent with the steps described above; comments have been added as indicated with an asterisk (*).
*Atmel AT88SC0104CA Initialization Example
*WRITE DATA TO USER ZONES
*Set User Zone 0
00 B4 03 00 00
*Write data = Zone 0 Data
00 B0 00 00 0B 5A 6F 6E 65 20 30 20 44 61 74 61
*Set User Zone 1
00 B4 03 01 00
*Write data = Zone 1 Data
00 B0 00 00 0B 5A 6F 6E 65 20 31 20 44 61 74 61
*Set User Zone 2
B4 03 02 00
*Write data = Zone 2 Data
B0 00 00 0B 5A 6F 6E 65 20 32 20 44 61 74 61
*Set User Zone 3
B4 03 03 00
*Write data = Zone 3 Data
B0 00 00 0B 5A 6F 6E 65 20 33 20 44 61 74 61
*UNLOCK CONFIGURATION ZONE
00 BA 07 00 03 DD 42 97
*WRITE CODES IN CONFIGURATION ZONE
*Write Card Mfg Code = P001
00 B4 00 0B 04 50 30 30 31
*Write Identification Number = 00000000012345
00 B4 00 19 07 00 00 00 00 01 23 45
*Write Issuer Code = STATION 035
00 B4 00 40 10 53 54 41 54 49 4F 4E 20 30 33 35 00 00 00 00 00
*WRITE REGISTERS IN CONFIGURATION ZONE
*Write Registers AR1/PR1 = 7F F9
00 B4 00 22 02 7F F9 DF BF 57 B9
*WRITE KEYS IN CONFIGURATION MEMORY
*Write Ci for set 2 = 22222222222222
B4 00 71 07 22 22 22 22 22 22 22
*Write Gc for set 2 = 5B4F9AE4B5098BE7
B4 00 A0 08 5B 4F 9A E4 B5 09 8B E7
*WRITE PASSWORDS IN CONFIGURATION MEMORY
*WRITE PASSWORDS IN CONFIGURATION ZONE
*Write Passwords, read 7 = 10 00 01, write 7 = 11 00 11
00 B4 00 B9 07 11 00 11 FF 10 00 01
*READ ENTIRE CONFIGURATION ZONE TO VERIFY
00 B6 00 00 F0
AtmeL
AT88SC0104CA/0204CA/0404CA/0808CA [Datasheet]
Atmel-8664I-CryptoMem-Low-Density-Full-Specification-Datasheet_072015
58
*Device Response:
3B B2 11 00 10 80 00 01 10 10 FF 50 30 30 31 FF
8C AD A8 10 0A AB FF FF FB 00 00 00 00 01 23 45
FF FF 7F F9 FF FF FF FF FF FF FF FF FF FF FF FF
FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
53 54 41 54 49 4F 4E 20 30 33 35 00 00 00 00 00
FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
FF FF FF FF FF FF FF FF FF 11 00 11 FF 10 00 01
FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
*SET SECURITY FUSES
*Set FAB Fuse
00 B4 01 06 00
*Set CMA Fuse
00 B4 01 04 00
*Set PER Fuse
00 B4 01 00 00
*Read Fuse Byte = X0
00 B6 01 00 01
*Device Response:
00
90 00
Atmel
AT88SC0104CA/0204CA/0404CA/0808CA [Datasheet]
Atmel-8664I-CryptoMem-Low-Density-Full-Specification-Datasheet_072015
59
12. Absolute Maximum Ratings*
Operating temperature .................... 40°C to +85°C
Storage temperature ................... 65°C to + 150°C
Voltage on any pin
with respect to ground ............... 0.7 to VCC +0.7V
Maximum operating voltage ................................ 6V
DC output current ............................................ 5mA
*NOTICE: Stresses beyond those listed under “Absolute
Maximum Ratings” may cause permanent damage to
the device. This is a stress rating only and functional
operation of the device at these or any other condition
beyond those indicated in the operational sections of
this specification is not implied. Exposure to absolute
maximum rating conditions for extended periods of
time may affect device reliability.
12.1 DC and AC Characteristics
Table 12-1. DC Characteristics
Symbol
Parameter
Test Condition
Min
Typ
Max
Units
VCC
Supply Voltage
2.7
3.6
V
ICC
Supply Current (VCC = 3.3V)
Async Read at 3.57MHz
5
mA
ICC
Supply Current (VCC = 3.3V)
Async Write at 3.57MHz
5
mA
ICC
Supply Current (VCC = 3.3V)
Synch Read at 1MHz
5
mA
ICC
Supply Current (VCC = 3.3V)
Synch Write at 1MHz
5
mA
ISB
Standby Current (VCC = 3.3V)
VIN = VCC or GND
100
A
VIL
SDA/IO Input Low Voltage
0
VCC x 0.2
V
VIL
CLK Input Low Voltage
0
VCC x 0.2
V
VIL
RST Input Low Voltage
0
VCC x 0.2
V
VIH(3)
SDA/IO Input High Voltage
VCC x 0.7
5.5
V
VIH(3)
SCL/CLK Input High Voltage
VCC x 0.7
5.5
V
VIH(3)
RST Input High Voltage
VCC x 0.7
5.5
V
IIL
SDA/IO Input Low Current
0 < VIL < VCC x 0.15
15
A
IIL
SCL/CLK Input Low Current
0 < VIL < VCC x 0.15
15
A
IIL
RST Input Low Current
0 < VIL < VCC x 0.15
50
A
IIH
SDA/IO Input High Current
VCC x 0.7 < VIH < VCC
20
A
IIH
SCL/CLK Input High Current
VCC x 0.7 < VIH < VCC
100
A
IIH
RST Input High Voltage
VCC x 0.7 < VIH < VCC
150
A
VOH
SDA/IO Output High Voltage
20K  external pull-up
VCC x 0.7
VCC
V
VOL
SDA/IO Output Low Voltage
IOL = 1mA
0
VCC x 0.15
V
IOH
SDA/IO Output High Current
VOH
20
A
IOL
SDA/IO Output High Current
VOL
10
A
Notes: 1. Applicable over recommended operating voltage range from VCC = 2.7V to 3.6V.
2. TAC = -40°C to +85°C (unless otherwise noted).
3. To prevent latch up conditions from occurring during power up of the AT88SCXXXXCA, VCC must be turned on
before applying VIH. For powering down, VIH must be removed before turning VCC off.
<7 |¢—=""> # J —~ ”W ///////W AAAAA
AT88SC0104CA/0204CA/0404CA/0808CA [Datasheet]
Atmel-8664I-CryptoMem-Low-Density-Full-Specification-Datasheet_072015
60
Table 12-2. AC Characteristics
Symbol
Parameter
Min
Max
Units
fCLK
Async Clock Frequency
1
4
MHz
fCLK
Synch Clock Frequency
0
1
MHz
Clock Duty cycle
40
60
%
tR
Rise Time: SDA/IO, RST
1
s
tF
Fall Time: SDA/IO, RST
1
s
tR
Rise Time: SCL/CLK
9% x period
s
tF
Fall Time: SCL/CLK
9% x period
s
tAA
Clock Low to Data Out Valid
250
ns
tHD.STA
Start Hold Time
200
ns
tSU.STA
Start Set-up Time
200
ns
tHD.DAT
Data In Hold Time
10
ns
tSU.DAT
Data In Set-up Time
100
ns
tSU.STO
Stop Set-up Time
200
ns
tDH
Data Out Hold Time
20
ns
tWR
Write Cycle Time
5
ms
Notes: 1. Applicable over recommended operating range from VCC = 2.7V to 3.6V.
2. TAC = -40°C to +85°C, CL = 30pF (unless otherwise noted).
12.2 Timing Diagrams for Synchronous Communications
Figure 12-1. Bus Timing
SCL: Serial Clock, SDA: Serial Data I/O
SCL
SDA IN
SDA OUT
tF
tHIGH
tLOW tLOW
tR
tAA tDH tBUF
tSU.STO
tSU.DAT
tHD.DAT
tHD.STA
tSU.STA
"fl Hf WW
AT88SC0104CA/0204CA/0404CA/0808CA [Datasheet]
Atmel-8664I-CryptoMem-Low-Density-Full-Specification-Datasheet_072015
61
Figure 12-2. Write Cycle Timing
SCL: Serial Clock, SDA: Serial Data I/O
Note: The write cycle time tWR is the time from a valid stop condition of a write sequence to the end of the internal
clear/write cycle
Figure 12-3. Data Validity
tWR
(1)
STOP
CONDITION
START
CONDITION
WORDn
ACK
8th BIT
SCL
SDA
AtmeL
AT88SC0104CA/0204CA/0404CA/0808CA [Datasheet]
Atmel-8664I-CryptoMem-Low-Density-Full-Specification-Datasheet_072015
62
Figure 12-4. Start and Stop Definition
Figure 12-5. Output Acknowledge
SCL
DATA IN
DATA OUT
EGDELWONKCATRATS
9
8
1
Atmel
AT88SC0104CA/0204CA/0404CA/0808CA [Datasheet]
Atmel-8664I-CryptoMem-Low-Density-Full-Specification-Datasheet_072015
63
13. POR and Tamper Conditions
The CryptoMemory device family incorporates several tamper detection circuits to prohibit operation outside the limits of
reliable circuit operation.
13.1 Power On Reset (POR) Delay
Anytime the device is reset either on initial power up or by a tamper detection circuit, there is a time delay from when normal
conditions are restored to when the device may be operated. During this reset sequence all security flags within the device are
reset to their initial values.
13.2 Tamper Detection
CryptoMemory contains tamper detection sensors to detect operation outside of specified limits. These sensors monitor the
internal supply voltage and clock frequency. An additional sensor detects high intensity light attacks. The die is disabled and
will not function when tampering is detected.
AT88SC0104CA/0204CA/0404CA/0808CA [Datasheet]
Atmel-8664I-CryptoMem-Low-Density-Full-Specification-Datasheet_072015
64
14. Ordering Information
Atmel Ordering Code
Package
Delivery Information
Voltage
Range
Operating Range
Form
Quantity
AT88SCxxxxCA-MJ
M2 J Module - ISO
Tape and Reel
2.7V to 5.5V
Commercial
Temperature
(0°C to 70°C)
AT88SCxxxxCA-MP
M2 P Module - ISO
AT88SCxxxxCA-MJTG
M2 J Module - TWI
AT88SCxxxxCA-MPTG
M2 P Module - TWI
AT88SCxxxxCA-PU
8P3
Bulk (Tubes)
50 per Tube
Green Compliant
(Exceeds RoHS)
Industrial Temperature
(-40°C to 85°C)
AT88SCxxxxCA-SH
8S1
Bulk (Tubes)
100 per Tube
AT88SCxxxxCA-SH-T
Tape and Reel
4,000 per Reel
AT88SCxxxxCA-TH
8X
Bulk (Tubes)
100 per Tube
Industrial Temperature
(-40°C to 85°C)
AT88SCxxxxCA-TH-T
Tape and Reel
5,000 per Reel
AT88SCxxxxCA-Y6H-T
8MA2
Tape and Reel
5,000 per Reel
AT88SCxxxxCA-WI
7 mil Wafer
Notes: 1. Ordering Codes are valid for all devices covered by this datasheet. (See P.1 for a complete list).
Package Type(1) (2)
Description
M2 J Module : ISO or TWI
M2 ISO 7816 Smart Card Module
M2 P Module : ISO or TWI
M2 ISO 7816 Smart Card Module with Atmel® Logo
8P3
8-lead, 0.300” wide, Plastic Dual Inline (PDIP)
8S1
8-lead, 0.150” wide, Plastic Gull Wing Small Outline (JEDEC SOIC)
8X
8-lead, 4.4mm body, Plastic Thin Shrink Small Outline (TSSOP)
8MA2
8-lead, 2.0x3.0mm, 0.50mm pitch, Ultra Thin Mini-Map, Dual No Lead (DFN), (MLP 2x3)
Note: 1. Formal drawings may be obtained from an Atmel sales office.
2. Both the J and P module packages are used for either ISO (T=0 / 2-wire mode) or TWI (2-wire mode only).
AtmeL Atmel
AT88SC0104CA/0204CA/0404CA/0808CA [Datasheet]
Atmel-8664I-CryptoMem-Low-Density-Full-Specification-Datasheet_072015
65
15. Package Marking Information
15.1 AT88SC0104CA
DRAWING NO. REV.
TITLE
Catalog Number Truncation
AT88SC0104CA Truncation Code ######: 0104CA ##: 11 #: 1
U YYWW
0104CA
AT88SC
8-lead PDIP
H YMXX @
0104CA
AT88SC
8-lead SOIC
8-lead TSSOP
AAAAAAA
800110
YWWH
8-lead UDFN
81
H10
YXX
2.0 x 3.0 mm Body
Note 2: Package drawings are not to scale
Note 1: designates pin 1
Top side only marking this package
Package Mark Contact:
DL-CSO-Assy_eng@atmel.com 88SC0104CASM A
3/6/12
88SC0104CASM, AT88SC0104CA Package Marking Information
Date Codes
Y = Year M = Month YY = Year WW = Work Week of Assembly
2: 2012 6: 2016 A = January 12: 2014 16: 2016 02: Week 2
3: 2013 7: 2017 B = February 13: 2013 17: 2017 04: Week 4
4: 2014 8: 2018 ... 14: 2014 18: 2018 ...
5: 2015 9: 2019 L = December 15: 2015 19: 2019 52: Week 52
Country of Assembly Lot Number Grade/Lead Finish Material
@ = Country of Assembly AAA...A = Atmel Wafer Lot Number U: Industrial/Matte Tin
Marked on bottom side for PDI P Marked on Bottom side for H: Industrial/NiPdAu
only unless in injector mold PDIP only
Trace Code Atmel Truncation
XX = Trace Code (Atmel Lot Numbers to Correspond to Code) AT: Atmel
Example: AA, AB.... YZ, ZZ
AT88SC0104CA: Package Marking Information
AtmeL AtmeL
AT88SC0104CA/0204CA/0404CA/0808CA [Datasheet]
Atmel-8664I-CryptoMem-Low-Density-Full-Specification-Datasheet_072015
66
15.2 AT88SC0204CA
DRAWING NO. REV.
TITLE
Catalog Number Truncation
AT88SC0204CA Truncation Code ######: 0204CA ##: 22 #: 2
U YYWW
0204CA
AT88SC
8-lead PDIP
H YMXX @
0204CA
AT88SC
8-lead SOIC
8-lead TSSOP
AAAAAAA
800220
YWWH
8-lead UDFN
82
H20
YXX
2.0 x 3.0 mm Body
Note 2: Package drawings are not to scale
Note 1: designates pin 1
Top side only marking this package
88SC0204CASM A
3/6/12
88SC0204CASM, AT88SC0204CA Package Marking Information
Date Codes
Y = Year M = Month YY = Year WW = Work Week of Assembly
2: 2012 6: 2016 A = January 12: 2014 16: 2016 02: Week 2
3: 2013 7: 2017 B = February 13: 2013 17: 2017 04: Week 4
4: 2014 8: 2018 ... 14: 2014 18: 2018 ...
5: 2015 9: 2019 L = December 15: 2015 19: 2019 52: Week 52
Country of Assembly Lot Number Grade/Lead Finish Material
@ = Country of Assembly AAA...A = Atmel Wafer Lot Number U: Industrial/Matte Tin
Marked on bottom side for PDI P Marked on Bottom side for H: Industrial/NiPdAu
only unless in injector mold PDIP only
Trace Code Atmel Truncation
XX = Trace Code (Atmel Lot Numbers to Correspond to Code) AT: Atmel
Example: AA, AB.... YZ, ZZ
AT88SC0204CA: Package Marking Information
Package Mark Contact:
DL-CSO-Assy_eng@atmel.com
AtmeL Atmel
AT88SC0104CA/0204CA/0404CA/0808CA [Datasheet]
Atmel-8664I-CryptoMem-Low-Density-Full-Specification-Datasheet_072015
67
15.3 AT88SC0404CA
DRAWING NO. REV.
TITLE
Catalog Number Truncation
AT88SC0404CA Truncation Code ######: 0404CA ##: 44 #: 4
U YYWW
0404CA
AT88SC
8-lead PDIP
H YMXX @
0404CA
AT88SC
8-lead SOIC
8-lead TSSOP
AAAAAAA
800440
YWWH
8-lead UDFN
84
H40
YXX
2.0 x 3.0 mm Body
Note 2: Package drawings are not to scale
Note 1: designates pin 1
Top side only marking this package
Package Mark Contact:
DL-CSO-Assy_eng@atmel.com 88SC0404CASM A
3/6/12
88SC0404CASM, AT88SC0404CA Package Marking Information
Date Codes
Y = Year M = Month YY = Year WW = Work Week of Assembly
2: 2012 6: 2016 A = January 12: 2014 16: 2016 02: Week 2
3: 2013 7: 2017 B = February 13: 2013 17: 2017 04: Week 4
4: 2014 8: 2018 ... 14: 2014 18: 2018 ...
5: 2015 9: 2019 L = December 15: 2015 19: 2019 52: Week 52
Country of Assembly Lot Number Grade/Lead Finish Material
@ = Country of Assembly AAA...A = Atmel Wafer Lot Number U: Industrial/Matte Tin
Marked on bottom side for PDI P Marked on Bottom side for H: Industrial/NiPdAu
only unless in injector mold PDIP only
Trace Code Atmel Truncation
XX = Trace Code (Atmel Lot Numbers to Correspond to Code) AT: Atmel
Example: AA, AB.... YZ, ZZ
AT88SC0404CA: Package Marking Information
Atmel AtmeL
AT88SC0104CA/0204CA/0404CA/0808CA [Datasheet]
Atmel-8664I-CryptoMem-Low-Density-Full-Specification-Datasheet_072015
68
15.4 AT88SC0808CA
DRAWING NO. REV.
TITLE
U YYWW
0808CA
AT88SC
8-lead PDIP
H YMXX @
0808CA
AT88SC
8-lead SOIC
8-lead TSSOP
AAAAAAA
800860
YWWH
8-lead UDFN
88
H60
YXX
2.0 x 3.0 mm Body
Note 2: Package drawings are not to scale
Note 1: designates pin 1
Top side only marking this package
Package Drawing Contact:
packagedrawings@atmel.com 88SC0808CASM B
11/10/14
88SC0808CASM, AT88SC0808CA Package Marking
Information
Date Codes
Y = Year M = Month YY = Year WW = Work Week of Assembly
4: 2014 8: 2018 A = January 14: 2014 18: 2018 02: Week 2
5: 2015 9: 2019 B = February 15: 2015 19: 2019 04: Week 4
6: 2016 0: 2020 ... 16: 2016 20: 2020 ...
7: 2017 1: 2021 L = December 17: 2017 21: 2021 52: Week 52
Country of Assembly Lot Number Grade/Lead Finish Material
@ = Country of Assembly AAA...A = Atmel Wafer Lot Number U: Industrial/Matte Tin
Marked on bottom side for PDI P Marked on Bottom side for H: Industrial/NiPdAu
only unless in injector mold PDIP only
Trace Code Atmel Truncation
XX = Trace Code (Atmel Lot Numbers to Correspond to Code) AT: Atmel
Example: AA, AB.... YZ, ZZ
AT88SC0808CA: Package Marking Information
Atmel
AT88SC0104CA/0204CA/0404CA/0808CA [Datasheet]
Atmel-8664I-CryptoMem-Low-Density-Full-Specification-Datasheet_072015
69
Appendix A. Errata
A.1 Send Checksum Command in TWI Mode
When a Write User Zone command is sent in authentication mode or encryption mode the data is saved in a buffer until a
cryptographic checksum is received. The host must send the checksum it has computed immediately after the Write User
Zone command. If the checksum is valid, CryptoMemory writes the data; if the checksum is incorrect the data is discarded and
the cryptographic engine is reset.
If there is any activity on the TWI bus between the Write User Zone command and the send checksum command the
EEPROM write may be aborted and the data in the user zone will be unchanged.
AtmeL
AT88SC0104CA/0204CA/0404CA/0808CA [Datasheet]
Atmel-8664I-CryptoMem-Low-Density-Full-Specification-Datasheet_072015
70
Appendix B. Revision History
Doc. Rev.
Date
Comments
8664I
07/2015
Added the AT88SCxxxxCA-TH-T tape and reel options.
8664H
03/2015
Added JEDEC SOIC tape and reel package options.
8664G
11/2014
Updated package marking information.
8664F
02/2014
Added package marking information and updated Atmel logos and disclaimer page.
8664E
12/2011
Updated template and added ordering information.
8664D
06/2011
Table 8-1, Atmel CryptoMemory Synchronous Command Set.
Correct value in “Verify Password, ADDR 1, from $0X to $1X.
8664C
01/2010
Converted to MS Word.
8664B
08/2009
Updated document.
8664A
05/2009
Initial document release.
AtmeE ‘ Enabling Unlimited Possibiiities’ “um-Ia
Atmel Corporation 1600 Technology Drive, San Jose, CA 95110 USA T: (+1)(408) 441.0311 F: (+1)(408) 436.4200 www.atmel.com
© 2015 Atmel Corporation. / Rev.:Atmel-8664I-CryptoMem-Low-Density-Full-Specification-Datasheet_072015.
Atmel®, Atmel logo and combinations thereof, Enabling Unlimited Possibilities®, CryptoMemory®, and others are registered trademarks or trademarks of Atmel
Corporation in U.S. and other countries. Other terms and product names may be trademarks of others.
DISCLAIMER: The information in this document is provided in connection with Atmel products. No license, express or implied, by estoppel or otherwise, to any intellectual property right is
granted by this document or in connection with the sale of Atmel products. EXCEPT AS SET FORTH IN THE ATMEL TERMS AND CONDITIONS OF SALES LOCATED ON THE ATMEL
WEBSITE, ATMEL ASSUMES NO LIABILITY WHATSOEVER AND DISCLAIMS ANY EXPRESS, IMPLIED OR STATUTORY WARRANTY RELATING TO ITS PRODUCTS INCLUDING, BUT
NOT LIMITED TO, THE IMPLIED WARRANTY OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE, OR NON-INFRINGEMENT. IN NO EVENT SHALL ATMEL BE LIABLE
FOR ANY DIRECT, INDIRECT, CONSEQUENTIAL, PUNITIVE, SPECIAL OR INCIDENTAL DAMAGES (INCLUDING, WITHOUT LIMITATION, DAMAGES FOR LOSS AND PROFITS,
BUSINESS INTERRUPTION, OR LOSS OF INFORMATION) ARISING OUT OF THE USE OR INABILITY TO USE THIS DOCUMENT, EVEN IF ATMEL HAS BEEN ADVISED OF THE
POSSIBILITY OF SUCH DAMAGES. Atmel makes no representations or warranties with respect to the accuracy or completeness of the contents of this document and reserves the right to
make changes to specifications and products descriptions at any time without notice. Atmel does not make any commitment to update the information contained herein. Unless specifically
provided otherwise, Atmel products are not suitable for, and shall not be used in, automotive applications. Atmel products are not intended, authorized, or warranted for use as components in
applications intended to support or sustain life.
SAFETY-CRITICAL, MILITARY, AND AUTOMOTIVE APPLICATIONS DISCLAIMER: Atmel products are not designed for and will not be used in connection with any applications where the
failure of such products would reasonably be expected to result in significant personal injury or death (“Safety-Critical Applications”) without an Atmel officer's specific written consent. Safety-
Critical Applications include, without limitation, life support devices and systems, equipment or systems for the operation of nuclear facilities and weapons systems. Atmel products are not
designed nor intended for use in military or aerospace applications or environments unless specifically designated by Atmel as military-grade. Atmel products are not designed nor intended for
use in automotive applications unless specifically designated by Atmel as automotive-grade.

Products related to this Datasheet

IC EEPROM 4K I2C 4MHZ 8SOIC
IC EEPROM 2K I2C 4MHZ 8SOIC
IC EEPROM 2K I2C 4MHZ 8SOIC
IC EEPROM 4K I2C 4MHZ 8TSSOP
IC EEPROM 2K I2C 4MHZ 8SOIC
IC EEPROM 1K I2C 4MHZ 8SOIC
IC EEPROM 1K I2C 4MHZ 8SOIC
IC EEPROM 2K I2C 4MHZ 8SOIC
IC EEPROM 1K I2C 4MHZ 8TSSOP
IC EEPROM 8K I2C 4MHZ 8SOIC
IC EEPROM 4K I2C 4MHZ 8SOIC
IC EEPROM 8K I2C 4MHZ 8SOIC
IC EEPROM 1K I2C 4MHZ 8DIP
IC EEPROM 2K I2C 4MHZ 8DIP
IC EEPROM 4K I2C 4MHZ 8DIP
IC EEPROM 4K I2C 4MHZ 8SOIC
IC EEPROM 8K I2C 4MHZ 8DIP
IC EEPROM 1K I2C 4MHZ M2 J
IC EEPROM 1K I2C 4MHZ M2 P
IC EEPROM 8K I2C 4MHZ M2 J
IC EEPROM 2K I2C 4MHZ M2 J
IC EEPROM 2K I2C 4MHZ M2 P
IC EEPROM 2K I2C 4MHZ 8TSSOP
IC EEPROM 8K I2C 4MHZ M2 P
IC EEPROM 4K I2C 4MHZ M2 P
IC EEPROM 4K I2C 4MHZ M2 J
IC EEPROM 4K I2C 4MHZ 8MINI MAP
IC EEPROM 4K I2C 4MHZ 8TSSOP
IC EEPROM 1K I2C 4MHZ 8TSSOP
IC EEPROM 2K I2C 4MHZ 8MINI MAP