MASW-004103-1365 Datasheet by MACOM Technology Solutions

httgs://www.macnm.comlsuggon www macum cum

Silicon SP4T Surface Mount HMIC PIN Diode Switch

50 MHZ - 20 GHz

Rev. V6

MASW-004103-1365

1

MACOM Technology Solutions Inc. (MACOM) and its affiliates reserve the right to make changes to the product(s) or information contained herein without notice.

Visit www.macom.com for additional data sheets and product information.

For further information and support please visit:

https://www.macom.com/support

DC-0008163

1

Features

 Operates 50 MHz to 20 GHz

 Usable up to 26 GHz

 Low Insertion Loss

 High Isolation

 Low Parasitic Capacitance and Inductance

 RoHS Compliant Surmount Package

 Rugged, Fully Monolithic

 Glass Encapsulated Construction

 Up to +38 dBm CW Power Handling @ +25°C

 Silicon Nitride Passivation

 Polymer Scratch Protection

 Solderable

Description

The MASW-004103-1365 is a SP4T, surmount,

broadband, monolithic switch using four sets of

series and shunt connected PIN diodes. This device

is designed for use in broadband, low to moderate

signal, high performance, switch applications up to

20 GHz. It is a surface mountable switch configured

for optimized performance and offers a distinct

advantage over MMIC, beamlead and chip and wire

hybrid designs. Because the PIN diodes of the

MASW-004103-1365 are integrated into the chip

and kept within close proximity, the parasitics

typically associated with other designs that use

individual components are kept to a minimum.

To minimize the parasitics and achieve high

performance the MASW-004103-1365 is fabricated

using MACOMs’ patented HMIC™ (Heterolithic

Microwave Integrated Circuit) process. This process

allows the silicon pedestals, which form the series

and shunt diodes or vias, to be imbeded in low loss,

low dispersion glass. The combination of low loss

glass and using tight spacing between elements

results in an HMIC device with low loss and high

isolation through low millimeter wave frequencies.

The topside is fully encapsulated with silicon nitride

and also has an additional layer of polymer for

scratch and impact protection. The protective

coating guards against damage to the junction and

the anode airbridges during handling and assembly.

On the backside of the chip gold metalized pads

have been added to produce a solderable surmount

device.

Pin Configuration

Pin Function

J1 RFC

J2 RF1

J3 RF2

J4 RF3

J5 RF4

J1

J2 J5

J3 J4

Functional Schematic

Ordering Information

Part # Package

MASW-004103-13650G 50 piece gel pack

MASW-004103-13655P 500 piece reel

MASW-004103-13650P 3000 piece reel

MASW-004103-001SMB Sample Test Board

MACOMW www macum com

Silicon SP4T Surface Mount HMIC PIN Diode Switch

50 MHZ - 20 GHz

Rev. V6

MASW-004103-1365

2

MACOM Technology Solutions Inc. (MACOM) and its affiliates reserve the right to make changes to the product(s) or information contained herein without notice.

Visit www.macom.com for additional data sheets and product information.

For further information and support please visit:

https://www.macom.com/support

DC-0008163

2

Parameter Conditions Units Min. Typ. Max.

Insertion Loss

6 GHz

13 GHz

20 GHz

dB —

0.5

0.8

1.2

0.6

1.0

1.5

Isolation

6 GHz

13 GHz

20 GHz

dB

48

38

29

51

39

32

—

Input Return Loss

6 GHz

13 GHz

20 GHz

dB

17

13

12

21

17

16

—

Output to Output Isolation

6 GHz

13 GHz

20 GHz

dB —

53.5

41.5

31.5

—

Input 0.1 dB Compression Point 2 GHz dBm — 36 —

IIP3

0.5 GHz, 5 MHz Spacing, 20 dBm

1 GHz, 10 MHz Spacing, 20 dBm

2 GHz, 10 MHz Spacing, 20 dBm

dBm —

60

63

64

—

Switching Speed1 — ns — 20 —

Voltage Rating2 — V — — 80

Electrical Specifications: TA = 25°C, PIN = 0 dBm, Z0 = 50 Ω, 20 mA, -10 V

1. Typical Switching Speed measured from 10% to 90 % of detected RF signal driven by TTL compatible drivers.

2. Maximum reverse leakage current in either the shunt or series PIN diodes shall be 0.5 µA maximum @ -80 volts.

Parameter Absolute Maximum

RF CW Incident Power

2 GHz

20 GHz

38 dBm

33 dBm

Applied Reverse Voltage |-80 V|

Junction Temperature +175°C

Operating Temperature -65°C to +125°C

Storage Temperature -65°C to +150°C

Absolute Maximum Ratings3,4,5

3. Exceeding any one or combination of these limits may cause

permanent damage to this device.

4. MACOM does not recommend sustained operation near these

survivability limits.

5. Combined maximum operating conditions for RF power, DC

bias, & temperature: 33 dBm CW, 20 mA per diode, +85ºC.

Handling Procedures

Please observe the following precautions to avoid

damage:

Static Sensitivity

These electronic devices are sensitive to

electrostatic discharge (ESD) and can be damaged

by static electricity. Proper ESD control techniques

should be used when handling these Class 1A HBM

devices.

MACOMW ‘‘‘‘‘‘ (1,!" www macum com

Silicon SP4T Surface Mount HMIC PIN Diode Switch

50 MHZ - 20 GHz

Rev. V6

MASW-004103-1365

3

MACOM Technology Solutions Inc. (MACOM) and its affiliates reserve the right to make changes to the product(s) or information contained herein without notice.

Visit www.macom.com for additional data sheets and product information.

For further information and support please visit:

https://www.macom.com/support

DC-0008163

3

-2.0

-1.5

-1.0

-0.5

0.0

0 5 10 15 20 25

J1 TO J2

J1 TO J3

J1 TO J4

J1 TO J5

Insertion Loss (dB)

Frequency (GHz)

-100

-80

-60

-40

-20

0

0 5 10 15 20 25

J1 TO J2

J1 TO J3

J1 TO J4

J1 TO J5

Isolation (dB)

Frequency (GHz)

-40

-30

-20

-10

0

0 5 10 15 20 25

J1 TO J2

J1 TO J3

J1 TO J4

J1 TO J5

Input Return Loss (dB)

Frequency (GHz)

-40

-30

-20

-10

0

0 5 10 15 20 25

J1 TO J2

J1 TO J3

J1 TO J4

J1 TO J5

Output Return Loss (dB)

Frequency (GHz)

-80

-60

-40

-20

0

0 5 10 15 20 25

J2 TO J3

J4 TO J5

Output to Output Isolation (dB)

Frequency (GHz)

0

2

4

6

8

10

12

0.0 0.2 0.4 0.6 0.8 1.0 1.2 1.4 1.6

Input Power (W)

Insertion Loss (dB)

2 GHz, 6.4 W

10 GHz, 3.1 W

20 GHz, 2 W

Typical Performance Curves: 20 mA, -10 V (On-Wafer Probed)

Input Return Loss

Insertion Loss

Output to Output Isolation Maximum Input Power,

Baseplate Temperature fixed @ 25°C

Isolation

Output Return Loss

MACOMW s 5 .71 ucoM E5 32 m m J—_ Inn; “-2 I m 1 _ 4» 7 = m m ,: :5 W .72 20ml : SZ X2 = nuswwm M—Kl— —{>0—l|' ‘_ —’ 2m 2m M_O m m R) my" war" m 41H" " * innF in; A W

Silicon SP4T Surface Mount HMIC PIN Diode Switch

50 MHZ - 20 GHz

Rev. V6

MASW-004103-1365

4

MACOM Technology Solutions Inc. (MACOM) and its affiliates reserve the right to make changes to the product(s) or information contained herein without notice.

Visit www.macom.com for additional data sheets and product information.

For further information and support please visit:

https://www.macom.com/support

DC-0008163

4

Condition of RF Output Control Level (DC Currents and Voltages)

B2 B3 B4 B5 J1-J2 J1-J3 J1-J4 J1-J5

-15 V at -20 mA6 +6 V at +20 mA +6 V at +20 mA +6 V at +20 mA Low Loss Isolation Isolation Isolation

+6 V at +20 mA -15 V at -20 mA6 +6 V at +20 mA +6 V at +20 mA Isolation Low Loss Isolation Isolation

+6 V at +20 mA +6 V at +20 mA -15 V at -20 mA6 +6 V at +20 mA Isolation Isolation Low Loss Isolation

+6 V at +20 mA +6 V at +20 mA +6 V at +20 mA -15 V at -20 mA6 Isolation Isolation Isolation Low Loss

Bias Control

Optimal operation of the MASW-004103-1365 is achieved by simultaneous application of negative DC voltage

and current to the low loss switching arm and positive DC voltage and current to the remaining switching arms

as shown in the applications circuit below. DC return is achieved via R2 on the RFC path. In the low loss state,

the series diode must be forward biased with current and the shunt diode reverse biased with voltage. In the

isolated arm, the shunt diode is forward biased with current and the series diode is reverse biased with voltage.

Driver Connections

Application Circuit7,8,9,10,11

7. Assume VF ~ 1 V @ 20 mA

8. R1 = 5 V / 0.02 A = 250 Ω; R2 = 9 V / 0.02 A = 450 Ω

9. PR1 = 0.02 A x 0.02 A x 250 = 0.1 W

10. PR2 = 0.02 A x 0.02 A x 450 = 0.18 W

11. Inductors shown in the above schematic are RF bias chokes. The operating bandwidth of a broad-band PIN diode switch is often

dependent on the bias components, particularly the RF bias chokes. It is suggested that the response at the frequencies of interest be

measured with all the bias components in place prior to installing of MASW-004103-1365.

Example:

J1 to J2→ Low Loss

R1 = 250 Ω

R2 = 450 Ω

B2 = -15 V

B3, B4, B5 = 6 V

6. The voltage applied to the off arm is allowed to vary provided a constant current is applied through the shunt diode on the off arm.

MACOMW Top View Side View Bottom View 125 2245 M 2m nu 2m 2m) an 277 «:3 ﬂ m E ﬁ/ sml 2nn nuz mm 29a IEZ nnz nnz H‘ m ': mu m www macum cum httgs:l/www.macnm.comlsuggon

Silicon SP4T Surface Mount HMIC PIN Diode Switch

50 MHZ - 20 GHz

Rev. V6

MASW-004103-1365

5

MACOM Technology Solutions Inc. (MACOM) and its affiliates reserve the right to make changes to the product(s) or information contained herein without notice.

Visit www.macom.com for additional data sheets and product information.

For further information and support please visit:

https://www.macom.com/support

DC-0008163

5

DIM Inches mm

Min. Max. Min. Max.

Width 0.06220 0.06417 1.580 1.630

Length 0.08740 0.08937 2.220 2.270

Thickness 0.00394 0.00591 0.100 0.150

Outline Drawing and Footprint (All dimensions in µm)12,13,14,15

12. Bottom view shows the back metal foot print and mounting pads.

13. All dimension are +/-0.5 µm.

14. Ground radius is 200 µm and centered on the I/O Pad.

15. The center pad shown on the chip bottom view must be connected to RF and DC ground.

DC & RF GND

Dimensions

MACOMW 170 230 170 J1 $1 320 F355' J2 17° 15 170 230 170 H 170 230 170 H 1528 170 170 170 170 I /' |«—.|‘—+—+—>|«—-|«—~|‘—>l<—’ 170="" 230="" 170="" 418="" 1703="" 230="" 170="" 307="" j3="" 320="" 320="" 2172="" www="" macum="" cum="" httgs://www.macnm.mmlsuggon="">

Silicon SP4T Surface Mount HMIC PIN Diode Switch

50 MHZ - 20 GHz

Rev. V6

MASW-004103-1365

6

MACOM Technology Solutions Inc. (MACOM) and its affiliates reserve the right to make changes to the product(s) or information contained herein without notice.

Visit www.macom.com for additional data sheets and product information.

For further information and support please visit:

https://www.macom.com/support

DC-0008163

6

Sample Board

Samples test boards are available upon request.

Handling Procedures

Attachment to a circuit board is made simple through the use of standard surface mount technology. Mounting

pads are conveniently located on the bottom of the chip and are removed from the active junction locations

making it well suited for solder attachment. Connections may be made onto hard or soft substrates via the use of

80Au/20Sn, or RoHS compliant solders. Typical re-flow profiles for provided in Application Note M538 , “Surface

Mounting Instructions“ and can viewed @ www.macom.com.

For applications where the average power is ≤1 W, a thermally conductive silver epoxy may also be used. Cure

per manufacturers recommended time and temperature. Typically 1 hour at 150°C.

When soldering these devices to a hard substrate, a solder re-flow method is preferred. A vacuum pick up tool

with a soft tip is recommended while placing the chip . When soldering to soft substrates, such as Duroid, a soft

solder is recommended at the circuit board to chip mounting pad interface to minimize stress due to any TCE

mismatches that may exist. Position the die so that its mounting pads are aligned with the circuit board land pads.

Solder reflow should not be performed by causing heat to flow through the top surface of the die to the back.

Since the HMIC glass is transparent, the edges of the mounting pads can be visually inspected through the die

after attachment is completed.

PCB Land Pattern (All dimensions in µm)

DC & RF GND

MACOMW idVJ. HEIHHVO

Silicon SP4T Surface Mount HMIC PIN Diode Switch

50 MHZ - 20 GHz

Rev. V6

MASW-004103-1365

7

MACOM Technology Solutions Inc. (MACOM) and its affiliates reserve the right to make changes to the product(s) or information contained herein without notice.

Visit www.macom.com for additional data sheets and product information.

For further information and support please visit:

https://www.macom.com/support

DC-0008163

7

Carrier Tape Dimensions

Chip Orientation in Tape

0.157 ±0.004

4.000 ±0.100

2.000 ±0.050

0.079 ±0.002

0.157 ±0.004

4.000 ±0.100

Ф 0.059 ±0.004 0.069 ±0.004

1.750 ±0.100

0.315

0.093 ±0.002

2.360 ±0.050 0.012 ±0.001

0.300 ±0.030

3.500 ±0.050

Ф 0.035 thru typ.

Ф 0.890

5° max. typ.

0.012 ±0.002

0.300 ±0.050

Pocket Depth

0.066 ±0.002

1.800 ±0.050

0.138 ±0.002

+0.012

-0.004

8.000 +0.30

-0.10

thru typ.

Ф 1.500 ±0.100

MACOMW W1 &W2 measured at hub W. W; /—’L I‘— www macum cum

Silicon SP4T Surface Mount HMIC PIN Diode Switch

50 MHZ - 20 GHz

Rev. V6

MASW-004103-1365

8

MACOM Technology Solutions Inc. (MACOM) and its affiliates reserve the right to make changes to the product(s) or information contained herein without notice.

Visit www.macom.com for additional data sheets and product information.

For further information and support please visit:

https://www.macom.com/support

DC-0008163

8

Dim. inches mm

Min. Max. Min. Max.

A 6.980 7.019 177.3 178.3

B 0.059 0.098 1.5 2.5

C 0.504 0.520 12.8 13.2

D 0.795 0.815 20.2 20.7

N 2.146 2.185 54.5 55.5

W1 0.331 0.337 8.4 8.55

W2 —- 0.567 —- 14.4

Reel Information

MACOM www macum com Img Ilwww macnm com/suggnn

Silicon SP4T Surface Mount HMIC PIN Diode Switch

50 MHZ - 20 GHz

Rev. V6

MASW-004103-1365

9

MACOM Technology Solutions Inc. (MACOM) and its affiliates reserve the right to make changes to the product(s) or information contained herein without notice.

Visit www.macom.com for additional data sheets and product information.

For further information and support please visit:

https://www.macom.com/support

DC-0008163

9

Information in this document is provided in connection with MACOM Technology Solutions Inc ("MACOM")

products. These materials are provided by MACOM as a service to its customers and may be used for

informational purposes only. Except as provided in MACOM's Terms and Conditions of Sale for such products or

in any separate agreement related to this document, MACOM assumes no liability whatsoever. MACOM

assumes no responsibility for errors or omissions in these materials. MACOM may make changes to

specifications and product descriptions at any time, without notice. MACOM makes no commitment to update

the information and shall have no responsibility whatsoever for conflicts or incompatibilities arising from future

changes to its specifications and product descriptions. No license, express or implied, by estoppels or otherwise,

to any intellectual property rights is granted by this document.

THESE MATERIALS ARE PROVIDED "AS IS" WITHOUT WARRANTY OF ANY KIND, EITHER EXPRESS OR

IMPLIED, RELATING TO SALE AND/OR USE OF MACOM PRODUCTS INCLUDING LIABILITY OR

WARRANTIES RELATING TO FITNESS FOR A PARTICULAR PURPOSE, CONSEQUENTIAL OR

INCIDENTAL DAMAGES, MERCHANTABILITY, OR INFRINGEMENT OF ANY PATENT, COPYRIGHT OR

OTHER INTELLECTUAL PROPERTY RIGHT. MACOM FURTHER DOES NOT WARRANT THE ACCURACY

OR COMPLETENESS OF THE INFORMATION, TEXT, GRAPHICS OR OTHER ITEMS CONTAINED WITHIN

THESE MATERIALS. MACOM SHALL NOT BE LIABLE FOR ANY SPECIAL, INDIRECT, INCIDENTAL, OR

CONSEQUENTIAL DAMAGES, INCLUDING WITHOUT LIMITATION, LOST REVENUES OR LOST PROFITS,

WHICH MAY RESULT FROM THE USE OF THESE MATERIALS.

MACOM products are not intended for use in medical, lifesaving or life sustaining applications. MACOM

customers using or selling MACOM products for use in such applications do so at their own risk and agree to

fully indemnify MACOM for any damages resulting from such improper use or sale.

MASW-004103-1365 Datasheet by MACOM Technology Solutions

Products related to this Datasheet