B41041, B43041 Series Datasheet by TDK Electronics Inc.
View All Related Products | Download PDF Datasheet
TDK
Single-ended Aluminum electrolytic capacitors
Series/Type: B41041
The following products presented in this data sheet are being withdrawn.
Ordering Code Substitute Product Date of
Withdrawal Deadline Last
Orders Last Shipments
B43041* B43851 2013-02-22 2013-09-30 2014-03-31
B41041* B41851 2013-02-22 2013-09-30 2014-03-31
For further information please contact your nearest EPCOS sales office, which will also support
you in selecting a suitable substitute. The addresses of our worldwide sales network are
presented at www.epcos.com/sales.
KASTDK
Single-ended capacitors B41041, B43041
Low impedance – 105 °C
308/08
Please read Cautions and warnings and
Important notes at the end of this document.
Specifications and characteristics in brief
Rated voltage VR6.3 … 450 V DC
Operating tempera-
ture range
–40 °C … +105 °C
Rated capacitance CR
(20 °C, 120 Hz)
0.1 … 15000 µF
Capacitance tolerance ±20% M
Load life
(105 °C, VR, IAC,R)
2000 h Requirements:
∆C/C ≤ ±20% of initial value
tan δ≤ 2 times initial specified limit
Ileak ≤ initial specified limit
Leakage current Ileak
(20 °C, after 5 minutes)
Dissipation factor
tan δ
(20 °C, 120 Hz)
For capacitance higher than 1000 µF add 0.02 for every increase of 1000 µF
VR (V DC) 6.3 10 16 25 35 50 63 ... 100 160 ... 250 315 ... 450
tan δ0.24 0.20 0.16 0.14 0.12 0.10 0.09 0.15 0.20
Low temperature
stability (impedance
ratio) (120 Hz)
VR (V DC) 6.3 ... 10 16 25 ... 100 160 ... 250 315 ... 450
75486
Shelf life After storage for 1000 h at 105 °C, the capacitors shall meet the require-
ment of load life test after reforming process. After test: VR to be applied for
30 minutes, 24 to 48 hours before measurement.
Frequency multiplier
for rated ripple current
Frequency
VR C
R50 Hz 120 Hz 1 kHz 10 kHz 100 kHz
6.3 ... 100 V 0.1 ... 6.8 µF– 0.4 0.7 0.8 1.0
10 ... 68 µF– 0.5 0.8 0.9 1.0
100 ... 200 µF– 0.7 0.9 0.9 1.0
330 ...
1000 µF
– 0.8 0.9 1.0 1.0
2200 ...
15000 µF
– 0.9 1.0 1.0 1.0
160 ... 450 V 0.47 ... 330 0.8 1 1.3 1.4 1.6
Temperature multi-
plier for rated ripple
current
+70 °C+85 °C +105 °C
6.3 ... 100 V 2.0 1.7 1.0
160 ... 400 V 1.8 1.4 1.0
Ileak 0.03 µA CR
µF
------- VR
V
-------
⋅
⎝⎠
⎛⎞
or 3 µA, whichever is greater⋅≤
Z40 °C–()
Z +20 °C()
---------------------------
AEC-C_B41041_B43041.book Seite 3 Dienstag, 5. August 2008 4:02 16
@TDK
Single-ended capacitors B41041, B43041
Low impedance – 105 °C
408/08
Please read Cautions and warnings and
Important notes at the end of this document.
Dimensional drawing
Safety vent for diameter ≥ 8 mm.
Case dimensions
d × l
mm
dmax × Imax
mm
a
mm
b
mm
5× 11 5.5 × 12.5 2.0 ±0.5 0.5 ±0.1
6.3 × 11 6.8 × 12.5 2.5 ±0.5 0.5 ±0.1
8× 11.5 8.5 × 13.0 3.5 ±0.5 0.6 ±0.1
10 × 12.5 11 × 14.0 5.0 ±0.5 0.6 ±0.1
10 × 16 11 × 17.5 5.0 ±0.5 0.6 ±0.1
10 × 20 11 × 21.5 5.0 ±0.5 0.6 ±0.1
12.5 × 20 13.5 × 22.0 5.0 ±0.5 0.6 ±0.1
12.5 × 25 13.5 × 27.0 5.0 ±0.5 0.6 ±0.1
16 × 25 17 × 27.0 7.5 ±0.5 0.8 ±0.1
16 × 31.5 17 × 33.5 7.5 ±0.5 0.8 ±0.1
16 × 35.5 17 × 37.5 7.5 ±0.5 0.8 ±0.1
18 × 35.5 19 × 37.5 7.5 ±0.5 0.8 ±0.1
18 × 40 19 × 42.0 7.5 ±0.5 0.8 ±0.1
KAL1080-C-E
a
d
marking
15 min. 5 min.
-
+
øb
Minus pole Safety vent
l
AEC-C_B41041_B43041.book Seite 4 Dienstag, 5. August 2008 4:02 16
KASTDK
Single-ended capacitors B41041, B43041
Low impedance – 105 °C
508/08
Please read Cautions and warnings and
Important notes at the end of this document.
Overview of available types B41041
VR (V DC) 6.3 10 16 25
Case dimensions d × l (mm)
CR (µF)
4.7 5× 11
6.8 5× 11
10 5 × 11 5 × 11
15 5 × 11 5 × 11
22 5 × 11 5 × 11 5 × 11
33 5 × 11 5 × 11 5 × 11 5 × 11
47 5 × 11 5 × 11 5 × 11 5 × 11
68 5 × 11 5 × 11 6.3 × 11 6.3 × 11
100 5 × 11 5 × 11 6.3 × 11 6.3 × 11
150 6.3 × 11 6.3 × 11 8 × 11.5 8 × 11.5
220 6.3 × 11 6.3 × 11 8 × 11.5 8 × 11.5
330 6.3 × 11 8 × 11.5 8 × 11.5 10 × 12.5
470 8 × 11.5 8 × 11.5 10 × 12.5 10 × 16
680 10 × 12.5 10 × 12.5 10 × 16 12.5 × 20
1000 10 × 12.5 10 × 16 10 × 20 12.5 × 20
1500 10 × 20 10 × 20 12.5 × 20 16 × 25
2200 12.5 × 20 12.5 × 20 12.5 × 25 16 × 25
3300 12.5 × 20 12.5 × 25 16 × 25 16 × 31.5
4700 16 × 25 16 × 25 16 × 31.5 18 × 35.5
6800 16 × 25 16 × 31.5 18 × 35.5
10000 16 × 31.5 18 × 35.5
15000 18 × 35.5
AEC-C_B41041_B43041.book Seite 5 Dienstag, 5. August 2008 4:02 16
{EASTDK
Single-ended capacitors B41041, B43041
Low impedance – 105 °C
608/08
Please read Cautions and warnings and
Important notes at the end of this document.
Overview of available types B41004
VR (V DC) 35 50 63 100
Case dimensions d × l (mm)
CR (µF)
0.10 5 × 11
0.22 5 × 11
0.33 5 × 11
0.47 5 × 11 5 × 11
0.68 5 × 11 5 × 11
1.0 5 × 11 5 × 11
1.5 5 × 11 5 × 11
2.2 5 × 11 5 × 11
3.3 5 × 11 5 × 11
4.7 5 × 11 5 × 11 5 × 11 5 × 11
6.8 5 × 11 5 × 11 5 × 11 6.3 × 11
10 5 × 11 5 × 11 5 × 11 6.3 × 11
15 5 × 11 5 × 11 6.3 × 11 8 × 11.5
22 5 × 11 5 × 11 6.3 × 11 8 × 11.5
33 5 × 11 6.3 × 11 6.3 × 11 10 × 12.5
47 6.3 × 11 6.3 × 11 8 × 11.5 10 × 16
68 8 × 11.5 8 × 11.5 10 × 12.5 10 × 20
100 8 × 11.5 8 × 11.5 10 × 12.5 12.5 × 20
150 10 × 12.5 10 × 12.5 10 × 16 12.5 × 25
220 10 × 12.5 10 × 16 10 × 20 16 × 25
330 10 × 16 10 × 20 12.5 × 20 16 × 25
470 10 × 20 12.5 × 20 12.5 × 25 16 × 31.5
680 12.5 × 25 16 × 25 16 × 31.5
1000 12.5 × 25 16 × 25 16 × 31.5
1500 16 × 25 16 × 35.5
2200 16 × 31.5 18 × 35.5
3300 18 × 35.5
AEC-C_B41041_B43041.book Seite 6 Dienstag, 5. August 2008 4:02 16
{EASTDK
Single-ended capacitors B41041, B43041
Low impedance – 105 °C
708/08
Please read Cautions and warnings and
Important notes at the end of this document.
Overview of available types B43041
VR (V DC) 160 200 250
Case dimensions d × l (mm)
CR (µF)
2.2 6.3 × 11
3.3 6.3 × 11 8 × 11.5
4.7 6.3 × 11 8 × 11.5 8 × 11.5
6.8 8 × 11.5 8 × 11.5 10 × 12.5
10 8 × 11.5 10 × 12.5 10 × 16
15 10 × 12.5 10 × 16 10 × 20
22 10 × 16 10 × 20 12.5 × 20
33 10 × 20 12.5 × 20 12.5 × 20
47 12.5 × 20 12.5 × 25 12.5 × 25
68 12.5 × 25 12.5 × 25 16 × 25
82 12.5 × 25 16 × 25 16 × 25
100 16 × 25 16 × 25 16 × 31.5
150 16 × 31.5 16 × 31.5 18 × 31.5
220 18 × 31.5 18 × 31.5 18 × 35.5
330 18 × 35.5 18 × 40
AEC-C_B41041_B43041.book Seite 7 Dienstag, 5. August 2008 4:02 16
KASTDK
Single-ended capacitors B41041, B43041
Low impedance – 105 °C
808/08
Please read Cautions and warnings and
Important notes at the end of this document.
Overview of available types B43041
VR (V DC) 350 400 450
Case dimensions d × l (mm)
CR (µF)
0.47 6.3 × 11
0.68 6.3 × 11
1.0 6.3 × 11 8 × 11.5
1.5 6.3 × 11 8 × 11.5 8 × 11.5
2.2 8 × 11.5 8 × 11.5 8 × 11.5
3.3 8 × 11.5 8 × 11.5 10 × 12.5
4.7 10 × 12.5 10 × 12.5 10 × 16
6.8 10 × 12.5 10 × 16 10 × 20
10 10 × 16 10 × 20 12.5 × 20
15 10 × 20 12.5 × 20 12.5 × 25
22 12.5 × 20 12.5 × 25 12.5 × 25
33 12.5 × 25 16 × 25 16 × 25
47 16 × 25 16 × 25 16 × 31.5
68 16 × 31.5 16 × 31.5 18 × 31.5
82 18 × 31.5 18 × 31.5 18 × 35.5
100 18 × 35.5 18 × 35.5 18 × 40
150 18 × 40 18 × 40 18 × 45
AEC-C_B41041_B43041.book Seite 8 Dienstag, 5. August 2008 4:02 16
@TDK
Single-ended capacitors B41041, B43041
Low impedance – 105 °C
908/08
Please read Cautions and warnings and
Important notes at the end of this document.
*** = Version
000 = for standard leads, bulk
001 = for kinked leads, bulk
002 = for cut leads, bulk
016 = for taped leads, Ammo pack, lead spacing a = 2.0 mm
007 = for taped leads, Ammo pack, lead spacing a = 2.5 mm
006 = for taped leads, Ammo pack, lead spacing a = 3.5 mm
008 = for taped leads, Ammo pack, lead spacing a = 5.0 mm
Technical data and ordering codes B41041
VR
V DC
CR
120 Hz
20 °C
µF
Case
dimensions
d × l
mm
Z
100 kHz
20 °C
Ω
IAC,R
100 kHz
105 °C
mA
Ordering code
(composition see
below)
6.3 33 5 × 11 2.5 105 B41041A2336M***
47 5 × 11 1.5 120 B41041A2476M***
68 5 × 11 1.3 125 B41041A2686M***
100 5 × 11 1.2 130 B41041A2107M***
150 6.3 × 11 1.0 150 B41041A2157M***
220 6.3 × 11 0.87 180 B41041A2227M***
330 6.3 × 11 0.58 220 B41041A2337M***
470 8 × 11.5 0.39 315 B41041A2477M***
680 10 × 12.5 0.35 370 B41041A2687M***
1000 10 × 12.5 0.23 500 B41041A2108M***
1500 10 × 20 0.18 630 B41041A2158M***
2200 12.5 × 20 0.095 1000 B41041A2228M***
3300 12.5 × 20 0.090 1050 B41041A2338M***
4700 16 × 25 0.061 1670 B41041A2478M***
6800 16 × 25 0.056 1740 B41041A2688M***
10000 16 × 31.5 0.045 2110 B41041A2109M***
15000 18 × 35.5 0.036 2580 B41041A2159M***
10 22 5 × 11 2.5 92 B41041A3226M***
33 5 × 11 1.9 105 B41041A3336M***
47 5 × 11 1.5 120 B41041A3476M***
68 5 × 11 1.4 125 B41041A3686M***
100 5 × 11 1.2 130 B41041A3107M***
150 6.3 × 11 0.8 160 B41041A3157M***
220 6.3 × 11 0.58 220 B41041A3227M***
330 8 × 11.5 0.47 265 B41041A3337M***
470 8 × 11.5 0.39 315 B41041A3477M***
680 10 × 12.5 0.30 400 B41041A3687M***
1000 10 × 16 0.18 615 B41041A3108M***
1500 10 × 20 0.15 810 B41041A3158M***
2200 12.5 × 20 0.09 1050 B41041A3228M***
3300 12.5 × 25 0.068 1300 B41041A3338M***
4700 16 × 25 0.056 1740 B41041A3478M***
6800 16 × 31.5 0.045 2110 B41041A3688M***
10000 18 × 35.5 0.036 2580 B41041A3109M***
AEC-C_B41041_B43041.book Seite 9 Dienstag, 5. August 2008 4:02 16
@TDK
Single-ended capacitors B41041, B43041
Low impedance – 105 °C
10 08/08
Please read Cautions and warnings and
Important notes at the end of this document.
*** = Version
000 = for standard leads, bulk
001 = for kinked leads, bulk
002 = for cut leads, bulk
016 = for taped leads, Ammo pack, lead spacing a = 2.0 mm
007 = for taped leads, Ammo pack, lead spacing a = 2.5 mm
006 = for taped leads, Ammo pack, lead spacing a = 3.5 mm
008 = for taped leads, Ammo pack, lead spacing a = 5.0 mm
Technical data and ordering codes B41041
VR
V DC
CR
120 Hz
20 °C
µF
Case
dimensions
d × l
mm
Z
100 kHz
20 °C
Ω
IAC,R
100 kHz
105 °C
mA
Ordering code
(composition see
below)
16 10 5 × 11 2.5 92 B41041A4106M***
15 5 × 11 2.2 98 B41041A4156M***
22 5 × 11 1.9 105 B41041A4226M***
33 5 × 11 1.5 120 B41041A4336M***
47 5 × 11 1.2 130 B41041A4476M***
68 6.3 × 11 1 150 B41041A4686M***
100 6.3 × 11 0.58 220 B41041A4107M***
150 8 × 11.5 0.5 240 B41041A4157M***
220 8 × 11.5 0.47 290 B41041A4227M***
330 8 × 11.5 0.39 315 B41041A4337M***
470 10 × 12.5 0.23 500 B41041A4477M***
680 10 × 16 0.17 610 B41041A4687M***
1000 10 × 20 0.12 825 B41041A4108M***
1500 12.5 × 20 0.1 1000 B41041A4158M***
2200 12.5 × 25 0.068 1300 B41041A4228M***
3300 16 × 25 0.056 1740 B41041A4338M***
4700 16 × 31.5 0.045 2110 B41041A4478M***
6800 18 × 35.5 0.036 2580 B41041A4688M***
25 4.7 5 × 11 3 85 B41041A5475M***
6.8 5 × 11 2.7 88 B41041A5685M***
10 5 × 11 2.5 92 B41041A5106M***
15 5 × 11 2.2 98 B41041A5156M***
22 5 × 11 1.9 105 B41041A5226M***
33 5 × 11 1.5 120 B41041A5336M***
47 5 × 11 1.2 130 B41041A5476M***
68 6.3 × 11 0.8 150 B41041A5686M***
100 6.3 × 11 0.58 220 B41041A5107M***
150 8 × 11.5 0.5 260 B41041A5157M***
220 8 × 11.5 0.39 315 B41041A5227M***
330 10 × 12.5 0.23 500 B41041A5337M***
470 10 × 16 0.18 615 B41041A5477M***
680 12.5 × 20 0.14 830 B41041A5687M***
1000 12.5 × 20 0.09 1050 B41041A5108M***
1500 16 × 25 0.08 1200 B41041A5158M***
2200 16 × 25 0.056 1740 B41041A5228M***
3300 16 × 31.5 0.045 2110 B41041A5338M***
4700 18 × 35.5 0.036 2580 B41041A5478M***
AEC-C_B41041_B43041.book Seite 10 Dienstag, 5. August 2008 4:02 16
@TDK
Single-ended capacitors B41041, B43041
Low impedance – 105 °C
11 08/08
Please read Cautions and warnings and
Important notes at the end of this document.
*** = Version
000 = for standard leads, bulk
001 = for kinked leads, bulk
002 = for cut leads, bulk
016 = for taped leads, Ammo pack, lead spacing a = 2.0 mm
007 = for taped leads, Ammo pack, lead spacing a = 2.5 mm
006 = for taped leads, Ammo pack, lead spacing a = 3.5 mm
008 = for taped leads, Ammo pack, lead spacing a = 5.0 mm
Technical data and ordering codes B41041
VR
V DC
CR
120 Hz
20 °C
µF
Case
dimensions
d × l
mm
Z
100 kHz
20 °C
Ω
IAC,R
100 kHz
105 °C
mA
Ordering code
(composition see
below)
35 4.7 5 × 11 2.5 92 B41041A7475M***
6.8 5 × 11 2.2 98 B41041A7685M***
10 5 × 11 1.9 105 B41041A7106M***
15 5 × 11 1.7 110 B41041A7156M***
22 5 × 11 1.5 120 B41041A7226M***
33 5 × 11 1.5 130 B41041A7336M***
47 6.3 × 11 0.72 220 B41041A7476M***
68 8 × 11.5 0.5 240 B41041A7686M***
100 8 × 11.5 0.39 315 B41041A7107M***
150 10 × 12.5 0.3 370 B41041A7157M***
220 10 × 12.5 0.23 500 B41041A7227M***
330 10 × 16 0.18 615 B41041A7337M***
470 10 × 20 0.12 825 B41041A7477M***
680 12.5 × 25 0.1 1000 B41041A7687M***
1000 12.5 × 25 0.068 1300 B41041A7108M***
1500 16 × 25 0.06 1500 B41041A7158M***
2200 16 × 31.5 0.045 2110 B41041A7228M***
3300 18 × 35.5 0.036 2580 B41041A7338M***
50 0.1 5 × 11 18 10 B41041A6104M***
0.22 5 × 11 13 15 B41041A6224M***
0.33 5 × 11 10 18 B41041A6334M***
0.47 5 × 11 7 23 B41041A6474M***
0.68 5 × 11 6 25 B41041A6684M***
15× 11 4.9 35 B41041A6105M***
1.5 5 × 11 4.6 40 B41041A6155M***
2.2 5 × 11 4.2 53 B41041A6225M***
3.3 5 × 11 3.9 65 B41041A6335M***
4.7 5 × 11 3.6 82 B41041A6475M***
6.8 5 × 11 3.2 90 B41041A6685M***
10 5 × 11 2.7 100 B41041A6106M***
15 5 × 11 2.2 110 B41041A6156M***
22 5 × 11 1.9 125 B41041A6226M***
33 6.3 × 11 1.1 195 B41041A6336M***
47 6.3 × 11 0.9 245 B41041A6476M***
68 8 × 11.5 0.7 310 B41041A6686M***
AEC-C_B41041_B43041.book Seite 11 Dienstag, 5. August 2008 4:02 16
@TDK
Single-ended capacitors B41041, B43041
Low impedance – 105 °C
12 08/08
Please read Cautions and warnings and
Important notes at the end of this document.
*** = Version
000 = for standard leads, bulk
001 = for kinked leads, bulk
002 = for cut leads, bulk
016 = for taped leads, Ammo pack, lead spacing a = 2.0 mm
007 = for taped leads, Ammo pack, lead spacing a = 2.5 mm
006 = for taped leads, Ammo pack, lead spacing a = 3.5 mm
008 = for taped leads, Ammo pack, lead spacing a = 5.0 mm
Technical data and ordering codes B41041
VR
V DC
CR
120 Hz
20 °C
µF
Case
dimensions
d × l
mm
Z
100 kHz
20 °C
Ω
IAC,R
100 kHz
105 °C
mA
Ordering code
(composition see
below)
50 100 8 × 11.5 0.5 385 B41041A6107M***
150 10 × 12.5 0.45 450 B41041A6157M***
220 10 × 16 0.27 505 B41041A6227M***
330 10 × 20 0.18 675 B41041A6337M***
470 12.5 × 20 0.12 895 B41041A6477M***
680 16 × 25 0.1 1100 B41041A6687M***
1000 16 × 25 0.076 1495 B41041A6108M***
1500 16 × 35.5 0.068 1800 B41041A6158M***
2200 18 × 35.5 0.05 2190 B41041A6228M***
63 4.7 5 × 11 5.8 74 B41041A8475M***
6.8 5 × 11 4.5 80 B41041A8685M***
10 5 × 11 3.6 95 B41041A8106M***
15 6.3 × 11 2.8 110 B41041A8156M***
22 6.3 × 11 2.1 130 B41041A8226M***
33 6.3 × 11 1.7 160 B41041A8336M***
47 8 × 11.5 1.2 305 B41041A8476M***
68 10 × 12.5 0.9 350 B41041A8686M***
100 10 × 12.5 0.65 395 B41041A8107M***
150 10 × 16 0.46 460 B41041A8157M***
220 10 × 20 0.32 505 B41041A8227M***
330 12.5 × 20 0.22 660 B41041A8337M***
470 12.5 × 25 0.16 850 B41041A8477M***
680 16 × 31.5 0.12 1000 B41041A8687M***
1000 16 × 31.5 0.098 1430 B41041A8108M***
100 0.47 5 × 11 13 30 B41041A9474M***
0.68 5 × 11 12 35 B41041A9684M***
15× 11 11 45 B41041A9105M***
1.5 5 × 11 10 50 B41041A9155M***
2.2 5 × 11 9.2 60 B41041A9225M***
3.3 5 × 11 7.2 67 B41041A9335M***
4.7 5 × 11 6.3 75 B41041A9475M***
6.8 6.3 × 11 4.5 88 B41041A9685M***
10 6.3 × 11 3.3 110 B41041A9106M***
15 8 × 11.5 2.8 130 B41041A9156M***
22 8 × 11.5 1.4 165 B41041A9226M***
AEC-C_B41041_B43041.book Seite 12 Dienstag, 5. August 2008 4:02 16
@TDK
Single-ended capacitors B41041, B43041
Low impedance – 105 °C
13 08/08
Please read Cautions and warnings and
Important notes at the end of this document.
*** = Version
000 = for standard leads, bulk
001 = for kinked leads, bulk
002 = for cut leads, bulk
016 = for taped leads, Ammo pack, lead spacing a = 2.0 mm
007 = for taped leads, Ammo pack, lead spacing a = 2.5 mm
006 = for taped leads, Ammo pack, lead spacing a = 3.5 mm
008 = for taped leads, Ammo pack, lead spacing a = 5.0 mm
Technical data and ordering codes B41041
VR
V DC
CR
120 Hz
20 °C
µF
Case
dimensions
d × l
mm
Z
100 kHz
20 °C
Ω
IAC,R
100 kHz
105 °C
mA
Ordering code
(composition see
below)
100 33 10 × 12.5 0.94 305 B41041A9336M***
47 10 × 16 0.68 320 B41041A9476M***
68 10 × 20 0.4 410 B41041A9686M***
100 12.5 × 20 0.28 585 B41041A9107M***
150 12.5 × 25 0.22 670 B41041A9157M***
220 16 × 25 0.16 1120 B41041A9227M***
330 16 × 25 0.13 1290 B41041A9337M***
470 16 × 31.5 0.11 1350 B41041A9477M***
AEC-C_B41041_B43041.book Seite 13 Dienstag, 5. August 2008 4:02 16
@TDK
Single-ended capacitors B41041, B43041
Low impedance – 105 °C
14 08/08
Please read Cautions and warnings and
Important notes at the end of this document.
*** = Version
000 = for standard leads, bulk
001 = for kinked leads, bulk
002 = for cut leads, bulk
016 = for taped leads, Ammo pack, lead spacing a = 2.0 mm
007 = for taped leads, Ammo pack, lead spacing a = 2.5 mm
006 = for taped leads, Ammo pack, lead spacing a = 3.5 mm
008 = for taped leads, Ammo pack, lead spacing a = 5.0 mm
Technical data and ordering codes B43041
VR
V DC
CR
120 Hz
20 °C
µF
Case
dimensions
d × l
mm
IAC,R
100 kHz
105 °C
mA
Ordering code
(composition see
below)
160 4.7 6.3 × 11 34 B43041A1475M***
6.8 8 × 11.5 46 B43041A1685M***
10 8 × 11.5 56 B43041A1106M***
15 10 × 12.5 80 B43041A1156M***
22 10 × 16 110 B43041A1226M***
33 10 × 20 150 B43041A1336M***
47 12.5 × 20 200 B43041A1476M***
68 12.5 × 25 270 B43041A1686M***
82 12.5 × 25 295 B43041A1826M***
100 16 × 25 370 B43041A1107M***
150 16 × 31.5 508 B43041A1157M***
220 18 × 31.5 650 B43041A1227M***
330 18 × 35.5 850 B43041A1337M***
200 3.3 6.3 × 11 30 B43041A2335M***
4.7 8 × 11.5 43 B43041A2475M***
6.8 8 × 11.5 57 B43041A2685M***
10 10 × 12.5 81 B43041A2106M***
15 10 × 16 112 B43041A2156M***
22 10 × 20 145 B43041A2226M***
33 12.5 × 20 182 B43041A2336M***
47 12.5 × 25 240 B43041A2476M***
68 12.5 × 25 350 B43041A2686M***
82 16 × 25 400 B43041A2826M***
100 16 × 25 460 B43041A2107M***
150 16 × 31.5 620 B43041A2157M***
220 18 × 31.5 810 B43041A2227M***
330 18 × 40 1010 B43041A2337M***
250 2.2 6.3 × 11 27 B43041F2225M***
3.3 8 × 11.5 32 B43041F2335M***
4.7 8 × 11.5 46 B43041F2475M***
6.8 10 × 12.5 64 B43041F2685M***
10 10 × 16 88 B43041F2106M***
15 10 × 20 120 B43041F2156M***
22 12.5 × 20 160 B43041F2226M***
33 12.5 × 20 190 B43041F2336M***
AEC-C_B41041_B43041.book Seite 14 Dienstag, 5. August 2008 4:02 16
@TDK
Single-ended capacitors B41041, B43041
Low impedance – 105 °C
15 08/08
Please read Cautions and warnings and
Important notes at the end of this document.
*** = Version
000 = for standard leads, bulk
001 = for kinked leads, bulk
002 = for cut leads, bulk
016 = for taped leads, Ammo pack, lead spacing a = 2.0 mm
007 = for taped leads, Ammo pack, lead spacing a = 2.5 mm
006 = for taped leads, Ammo pack, lead spacing a = 3.5 mm
008 = for taped leads, Ammo pack, lead spacing a = 5.0 mm
Technical data and ordering codes B43041
VR
V DC
CR
120 Hz
20 °C
µF
Case
dimensions
d × l
mm
IAC,R
100 kHz
105 °C
mA
Ordering code
(composition see
below)
250 47 12.5 × 25 270 B43041F2476M***
68 16 × 25 350 B43041F2686M***
82 16 × 25 400 B43041F2826M***
100 16 × 31.5 460 B43041F2107M***
150 18 × 31.5 620 B43041F2157M***
220 18 × 35.5 830 B43041F2227M***
350 1.5 6.3 × 11 19 B43041A4155M***
2.2 8 × 11.5 30 B43041A4225M***
3.3 8 × 11.5 34 B43041A4335M***
4.7 10 × 12.5 50 B43041A4475M***
6.8 10 × 12.5 70 B43041A4685M***
10 10 × 16 92 B43041A4106M***
15 10 × 20 130 B43041A4156M***
22 12.5 × 20 165 B43041A4226M***
33 12.5 × 25 220 B43041A4336M***
47 16 × 25 290 B43041A4476M***
68 16 × 31.5 380 B43041A4686M***
82 18 × 31.5 480 B43041A4826M***
100 18 × 35.5 520 B43041A4107M***
150 18 × 40 650 B43041A4157M***
400 1 6.3 × 11 19 B43041A9105M***
1.5 8 × 11.5 26 B43041A9155M***
2.2 8 × 11.5 32 B43041A9225M***
3.3 8 × 11.5 40 B43041A9335M***
4.7 10 × 12.5 56 B43041A9475M***
6.8 10 × 16 77 B43041A9685M***
10 10 × 20 104 B43041A9106M***
15 12.5 × 20 143 B43041A9156M***
22 12.5 × 25 210 B43041A9226M***
33 16 × 25 280 B43041A9336M***
47 16 × 25 370 B43041A9476M***
68 16 × 31.5 480 B43041A9686M***
82 18 × 31.5 500 B43041A9826M***
100 18 × 35.5 580 B43041A9107M***
150 18 × 40 770 B43041A9157M***
AEC-C_B41041_B43041.book Seite 15 Dienstag, 5. August 2008 4:02 16
@TDK
Single-ended capacitors B41041, B43041
Low impedance – 105 °C
16 08/08
Please read Cautions and warnings and
Important notes at the end of this document.
*** = Version
000 = for standard leads, bulk
001 = for kinked leads, bulk
002 = for cut leads, bulk
016 = for taped leads, Ammo pack, lead spacing a = 2.0 mm
007 = for taped leads, Ammo pack, lead spacing a = 2.5 mm
006 = for taped leads, Ammo pack, lead spacing a = 3.5 mm
008 = for taped leads, Ammo pack, lead spacing a = 5.0 mm
Technical data and ordering codes B43041
VR
V DC
CR
120 Hz
20 °C
µF
Case
dimensions
d × l
mm
IAC,R
100 kHz
105 °C
mA
Ordering code
(composition see
below)
450 0.47 6.3 × 11 13 B43041A5474M***
0.68 6.3 × 11 16 B43041A5684M***
1.0 8 × 11.5 23 B43041A5105M***
1.5 8 × 11.5 28 B43041A5155M***
2.2 8 × 11.5 34 B43041A5225M***
3.3 10 × 12.5 49 B43041A5335M***
4.7 10 × 16 65 B43041A5475M***
6.8 10 × 20 90 B43041A5685M***
10 12.5 × 20 125 B43041A5106M***
15 12.5 × 25 170 B43041A5156M***
22 12.5 × 25 210 B43041A5226M***
33 16 × 25 280 B43041A5336M***
47 16 × 31.5 380 B43041A5476M***
68 18 × 31.5 480 B43041A5686M***
82 18 × 35.5 550 B43041A5826M***
100 18 × 40 650 B43041A5107M***
150 18 × 45 800 B43041A5157M***
AEC-C_B41041_B43041.book Seite 16 Dienstag, 5. August 2008 4:02 16
@TDK
Single-ended capacitors B41041, B43041
Taping, packing and lead configurations
17 08/08
Please read Cautions and warnings and
Important notes at the end of this document.
Taping, packing and lead configurations of single-ended capacitors
Single-ended capacitors are available taped in Ammo pack from diameter 4 to 10 mm as follows:
Lead spacing 2.0 mm (∅ d = 4 ... 5 mm)
Last 3 digits of ordering code: 016
Dimensions in mm
∅ dF H W W
0W1W2PP
0P1l1t∆hD
0
4 ... 5 2.0 18.5 18.0 7.0 9.0 3.0 12.7 12.7 5.10 1.0 0.7 1 4.0
–0.2 ±0.75 ±0.5 min. ±0.5 max. ±1.0 ±0.3 ±0.7 max. ±0.2 ±1.0 ±0.2
Adhesive tape
Base tape F
B
H
ød
P
W
t
KAL1138-D-E
1 max.
View B
P
0
0
H
P
1
D
0
W
0
W
2
W
1
1
l
h∆h∆
Single-ended capacitors B41041, B43041
Taping, packing and lead configurations
AEC-C_B41041_B43041.book Seite 17 Dienstag, 5. August 2008 4:02 16
{EASTDK
Single-ended capacitors B41041, B43041
Taping, packing and lead configurations
18 08/08
Please read Cautions and warnings and
Important notes at the end of this document.
Lead spacing 2.5 mm (∅ d = 4 ... 6.3 mm)
Last 3 digits of ordering code: 007
Lead spacing 3.5 mm (∅ d = 8 mm)
Last 3 digits of ordering code: 006
Dimensions in mm
∅ dFHH
0WW
0W1W2PP
0P1l1t∆hD
0
4 ... 6.3 2.5 18.5 16.0 18.0 7.0 9.0 3.0 12.7 12.7 5.10 1.0 0.7 0 4.0
To le ra nc e – 0 . 2 ±0.75 ±0.5 ±0.5 min. ±0.5 max. ±1.0 ±0.3 ±0.7 max. ±0.2 ±1.0 ±0.2
Dimensions in mm
∅ dFHWW
0W1W2PP
0P1l1t∆hD
0
8 3.5 18.5 18.0 10 9.0 3.0 12.7 12.7 5.10 1.0 0.7 1 4.0
Tol er an ce ±0.5 ±0.75 ±0.5 min. ±0.5 max. ±1.0 ±0.3 ±0.7 max. ±0.2 max. ±0.2
Adhesive tape
Base tape F
B
H
ød
P
W
t
KAL1074-3-E
1 max.
View B
P
0
0
H
P
1
D
0
W
0
W
2
W
1
1
l
h∆h∆
Adhesive tape
Base tape F
B
H
ød
P
W
t
KAL1138-D-E
1 max.
View B
P
0
0
H
P
1
D
0
W
0
W
2
W
1
1
l
h∆h∆
AEC-C_B41041_B43041.book Seite 18 Dienstag, 5. August 2008 4:02 16
{EASTDK
Single-ended capacitors B41041, B43041
Taping, packing and lead configurations
19 08/08
Please read Cautions and warnings and
Important notes at the end of this document.
Lead spacing 5.0 mm (∅ d = 4 ... 8 mm)
Last 3 digits of ordering code: 008
Lead spacing 5.0 mm (∅ d = 10 mm)
Last 3 digits of ordering code: 008
Taping is available up to dimensions d × l = 10 × 20 mm. For ∅ 12.5, 16 and 18 mm taping is not
available.
Dimensions in mm
∅ dFHH
0WW
0W1W2PP
0P1L1t∆hD
0
4 ... 6.3 5.0 18.5 16 18.0 7.0 9.0 3.0 12.7 12.7 3.85 1.0 0.6 2.0 4.0
8 5.0 18.5 16 18.0 10 9.0 3.0 12.7 12.7 3.85 1.0 0.6 2.0 4.0
10 5.0 18.5 – 18.0 12.5 9.0 3.0 12.7 12.7 3.85 1.0 0.6 2.0 4.0
Tolerance +0.6
–0.2
±0.75 ±0.5 +1.0
–0.5
+1.0
–0
±0.5 max. ±0.5 ±0.3 ±0.7 max. +0.3
–0.2
max. ±0.2
Adhesive tape
Base tape F
B
H
ød
P
W
KAL1075-B-E
t
1 max.
View B
0
P
P1
D0
H
0
1
W
W
2
W
0
1
l
h∆h∆
Adhesive tape
Base tape F
B
H
ød
P
W
KAL1076-J-E
t
1 max.
View B
P
0
P
1
D
0
W
0
W
2
W
1
1
l
h∆h∆
AEC-C_B41041_B43041.book Seite 19 Dienstag, 5. August 2008 4:02 16
@TDK
Single-ended capacitors B41041, B43041
Taping, packing and lead configurations
20 08/08
Please read Cautions and warnings and
Important notes at the end of this document.
Kinked or cut leads
Single-ended capacitors are available with kinked or cut leads. Other lead configurations also avail-
able on request.
Kinked leads
Last 3 digits of ordering code: 001
Case size d × l (mm) a (mm) Case size d × l (mm) a (mm)
4 × 7 1.5 12.5 × 16 5.0
5 × 7 2.0 12.5 × 20 5.0
5 × 11 2.0 12.5 × 25 5.0
6.3 × 7 2.5 12.5 × 31.5 5.0
6.3 × 11 2.5 12.5 × 35.5 5.0
6.3 × 15 2.5 12.5 × 40 5.0
8 × 7 3.5 16 × 20 7.5
8 × 11.5 3.5 16 × 25 7.5
8 × 15 3.5 16 × 31.5 7.5
8 × 20 3.5 16 × 35.5 7.5
10 × 12.5 5.0 16 × 40 7.5
10 × 16 5.0 18 × 20 7.5
10 × 20 5.0 18 × 25 7.5
10 × 25 5.0 18 × 31.5 7.5
10 × 31.5 5.0 18 × 35.5 7.5
18 × 40 7.5
ød
3.2±0.1
KAL1137-5
1.2±0.1
2.1±0.1
l
4.5±0.5
ød
KAL1084-A
a
l
AEC-C_B41041_B43041.book Seite 20 Dienstag, 5. August 2008 4:02 16
@TDK
Single-ended capacitors B41041, B43041
Taping, packing and lead configurations
21 08/08
Please read Cautions and warnings and
Important notes at the end of this document.
Cut leads
Last 3 digits of ordering code: 002
Case size d × l (mm) a (mm) Case size d × l (mm) a (mm)
4 × 7 1.5 12.5 × 16 5.0
5 × 7 2.0 12.5 × 20 5.0
5 × 11 2.0 12.5 × 25 5.0
6.3 × 7 2.5 12.5 × 31.5 5.0
6.3 × 11 2.5 12.5 × 35.5 5.0
6.3 × 15 2.5 12.5 × 40 5.0
8 × 7 3.5 16 × 20 7.5
8 × 11.5 3.5 16 × 25 7.5
8 × 15 3.5 16 × 31.5 7.5
8 × 20 5.0 16 × 35.5 7.5
10 × 12.5 5.0 16 × 40 7.5
10 × 16 5.0 18 × 20 7.5
10 × 20 5.0 18 × 25 7.5
10 × 25 5.0 18 × 31.5 7.5
10 × 31.5 5.0 18 × 35.5 7.5
18 × 40 7.5
ød
KAL1086-R
a
4.5±0.5
l
AEC-C_B41041_B43041.book Seite 21 Dienstag, 5. August 2008 4:02 16
@TDK
22 08/08
Please read Cautions and warnings and
Important notes at the end of this document.
General
Also see “Important notes” on page 24.
1 Aluminum electrolytic capacitors have a bi-polar structure. This is marked on the body of the
capacitor. A capacitor must not be mounted with reversed polarity. The application of an AC
or reverse voltage may cause a short circuit or damage the capacitor. Bi-polar capacitors
must not be used in AC applications, where the polarity may be reversed in the circuits or is
unknown.
2 The DC voltage applied to the capacitor terminal must not exceed its rated operating voltage,
as this will result in a rapid increase of the leakage current and may damage the capacitor. It
is recommended to operate the capacitor at 70–80% of its rated voltage to optimize its serv-
ice life.
3 The ripple current applied to the capacitor must be within the permitted range. An excessive
ripple current leads to impaired electrical properties and may damage the capacitor. Note that
the sum of the peak values of the ripple voltage and the DC operating voltage must not ex-
ceed the rated DC voltage.
4 Capacitors must be used within their permitted range of operating temperature. Operation at
room temperature optimizes their service life.
5 Capacitors with case diameter ≥8 mm are equipped with a safety vent. In capacitors fitted
with a lead or soldering lug, the safety vent is usually located at the base of the case. It needs
sufficient space around it to operate optimally. The following dimensions are recommended:
for case diameter d = 8 to 16 mm, more than 2 mm; for d =18 to 35 mm, more than 3 mm;
and for d = 42 mm or more, more than 5 mm.
6 Capacitors should not be mounted with the safety vent face down on the board. Do not locate
any wire or copper trace near the safety vent. Do not reverse the voltage, as this may result
in excess pressure and the leakage of electrolyte.
7 Gas is released through the safety vent when the pressure inside the capacitor is too high. A
gaseous liquid around the safety vent does not indicate a leakage of electrolyte.
8 The capacitor should be stored under conditions of normal temperature and in a non-acid,
non-alkali environment of normal humidity. Exposure to high temperatures, for example un-
der direct sunlight, will reduce its operating life. If the capacitor is stored in an environment
containing acids or alkalis, the solderability of the leads may be affected.
9 The leakage current of an aluminum electrolytic capacitor may increase after a long period
of storage. After such storage, the capacitor must be aged by applying the rated operating
voltage for 6–8 hours before use.
10 Manual soldering:
a Soldering must be performed within the specified conditions.
Bit temperature: 350 °C; application time of soldering iron: 3 seconds.
b Ensure that the soldering iron does not touch any part of the capacitor body.
Cautions and warnings
AEC-C_B41041_B43041.book Seite 22 Dienstag, 5. August 2008 4:02 16
@TDK
Cautions and warnings
23 08/08
Please read Cautions and warnings and
Important notes at the end of this document.
11 Do not apply excessive force to the leads and terminals. Do not move the capacitor after sol-
dering it onto the PC board and do not carry the PC board by gripping the capacitor. Observe
the following rules to prevent undue stress to the capacitor:
a Do not tilt or bend the capacitor after soldering.
b Ensure that the terminal spacing matches the corresponding hole spacing on the PC
board.
12 The aluminum case is not insulated from the cathode. Do not place a conductor under the
aluminum capacitors on the PC board as this may cause a short circuit. The case and top of
capacitors used in switched mode power supplies have a high-voltage-resistant heat shrink
sleeve to ensure safe usage.
13 The leads of capacitors with a case diameter exceeding 14 mm cannot be used for fixing.
AEC-C_B41041_B43041.book Seite 23 Dienstag, 5. August 2008 4:02 16
@TDK
Important notes
24 08/08
Important notes
The following applies to all products named in this publication:
1. Some parts of this publication contain statements about the suitability of our products for
certain areas of application. These statements are based on our knowledge of typical
requirements that are often placed on our products in the areas of application concerned. We
nevertheless expressly point out that such statements cannot be regarded as binding
statements about the suitability of our products for a particular customer application. As
a rule, EPCOS is either unfamiliar with individual customer applications or less familiar with them
than the customers themselves. For these reasons, it is always ultimately incumbent on the
customer to check and decide whether an EPCOS product with the properties described in the
product specification is suitable for use in a particular customer application.
2. We also point out that in individual cases, a malfunction of electronic components or failure
before the end of their usual service life cannot be completely ruled out in the current state
of the art, even if they are operated as specified. In customer applications requiring a very
high level of operational safety and especially in customer applications in which the malfunction
or failure of an electronic component could endanger human life or health (e.g. in accident
prevention or life-saving systems), it must therefore be ensured by means of suitable design of
the customer application or other action taken by the customer (e.g. installation of protective
circuitry or redundancy) that no injury or damage is sustained by third parties in the event of
malfunction or failure of an electronic component.
3. The warnings, cautions and product-specific notes must be observed.
4. In order to satisfy certain technical requirements, some of the products described in this
publication may contain substances subject to restrictions in certain jurisdictions (e.g.
because they are classed as hazardous). Useful information on this will be found in our
Material Data Sheets on the Internet (www.epcos.com/material). Should you have any more
detailed questions, please contact our sales offices.
5. We constantly strive to improve our products. Consequently, the products described in this
publication may change from time to time. The same is true of the corresponding product
specifications. Please check therefore to what extent product descriptions and specifications
contained in this publication are still applicable before or when you place an order.
We also reserve the right to discontinue production and delivery of products. Consequently,
we cannot guarantee that all products named in this publication will always be available. The
aforementioned does not apply in case of individual agreements deviating from the foregoing for
customer-specific products.
6. Unless otherwise agreed in individual contracts, all orders are subject to the current version
of the “General Terms of Delivery for Products and Services in the Electrical Industry”
published by the German Electrical and Electronics Industry Association (ZVEI).
7. The trade names EPCOS, BAOKE, Alu-X, CeraDiode, CSSP, CTVS, DSSP, MiniBlue, MKK,
MLSC, MotorCap, PCC, PhaseCap, PhaseMod, SIFERRIT, SIFI, SIKOREL, SilverCap,
SIMDAD, SIMID, SineFormer, SIOV, SIP5D, SIP5K, ThermoFuse, WindCap are trademarks
registered or pending in Europe and in other countries. Further information will be found on
the Internet at www.epcos.com/trademarks.
AEC-C_B41041_B43041.book Seite 24 Dienstag, 5. August 2008 4:02 16
Products related to this Datasheet
CAP ALUM 100UF 20% 6.3V RADIAL
CAP ALUM 1000UF 20% 6.3V RADIAL
CAP ALUM 10000UF 20% 6.3V RADIAL
CAP ALUM 150UF 20% 6.3V RADIAL
CAP ALUM 1500UF 20% 6.3V RADIAL
CAP ALUM 220UF 20% 6.3V RADIAL
CAP ALUM 2200UF 20% 6.3V RADIAL
CAP ALUM 33UF 20% 6.3V RADIAL
CAP ALUM 330UF 20% 6.3V RADIAL
CAP ALUM 3300UF 20% 6.3V RADIAL
CAP ALUM 47UF 20% 6.3V RADIAL
CAP ALUM 470UF 20% 6.3V RADIAL
CAP ALUM 4700UF 20% 6.3V RADIAL
CAP ALUM 68UF 20% 6.3V RADIAL
CAP ALUM 680UF 20% 6.3V RADIAL
CAP ALUM 6800UF 20% 6.3V RADIAL
CAP ALUM 100UF 20% 10V RADIAL
CAP ALUM 1000UF 20% 10V RADIAL
CAP ALUM 10000UF 20% 10V RADIAL
CAP ALUM 150UF 20% 10V RADIAL
CAP ALUM 1500UF 20% 10V RADIAL
CAP ALUM 22UF 20% 10V RADIAL
CAP ALUM 220UF 20% 10V RADIAL
CAP ALUM 2200UF 20% 10V RADIAL
CAP ALUM 33UF 20% 10V RADIAL
CAP ALUM 330UF 20% 10V RADIAL
CAP ALUM 3300UF 20% 10V RADIAL
CAP ALUM 47UF 20% 10V RADIAL
CAP ALUM 470UF 20% 10V RADIAL
CAP ALUM 4700UF 20% 10V RADIAL